Decode marelli 59f help

[kevfield]

Hi could anyone help? i seem to be struguling with IAW 59F ecu trying to decode it, i have read post on it on this forum but cant seem to get it to read, i have kwp+ and galletto but cant seem to get anywhere with it,with kwp i get kick but it dosnt seem to read ecu with galletto i get nowt would someone try and point me the right way please

Thanks kev

[melcool]

the number of HW on your ecu???

[kevfield]

is HW303 thanks for reply friend ;) i have kick now with galletto but still not read ecu

[kevfield]

I have managed to connect and extract software and hardware info with kwp+ software and looks like it will let me write to it but with 59f software still not connect to it any idea,s ? i read somewhere maybe 1k ris on k line anyone?? please

thanks kev

[steva33]

i CAN`T WRITE DUMP IN ECU,I TRY WITH GALETTO 1260 BUT NO SUCESS,PLEASE HELP

[rsibiza]

IAW59F needs boot mode,how to enter in boot in attach

To write new file into IAW59F this needs to be vergine,and as i have explained many times in this forum,this is possible as i know only with an special tool from Celeste (eletronica celeste ) in italia.

Sorry but pdf is also in italian.

Regards

[rsibiza]

I have managed to connect and extract software and hardware info with kwp+ software and looks like it will let me write to it but with 59f software still not connect to it any idea,s ? i read somewhere maybe 1k ris on k line anyone?? please

thanks kev


1K pullup resistor is for VAG not for IAW59F

[rsibiza]

Galetto

KWP2000

Cannot write IAW59F

[kevfield]

Ok i think i have read ecu now can someone check if file is ok and make immo off please

Thanks kev

[kevfield]

Last file is wrong now i read in boot mode :P at long last can someone now help me immo off :)

[landrovertdi]

with galletto read and write the same file
use driver "clona e decode iaw a4f / 59f st10f786 boot mode"
immo off

[kevfield]

So the file i have just read , i rewite it back and bits will have changed by galletto software?

[landrovertdi]

yes , driver galletto change bit in the file

[kevfield]

Ahhh i see now thank you so much for your help i think i have got there

[landrovertdi]

use file 320kb and bootmode

[kevfield]

yes i try to do that but galletto soft says changing speed error and then hangs but if i read again file from ecu has changed, i am not sure if new file in ecu is ok, do you have ori and immo off so i can compair

[landrovertdi]

read galletto 59f m3 hw303

[kevfield]

is this your ori dump?

[landrovertdi]

yes is my ori dump , write in your ecu whith driver " clona e decode "

[kevfield]

ok then is im*o off ? do i have to cut im*o wire or remove im*o box?

Thanks kev

[kevfield]

Anyone??

Thanks kev

[rsibiza]

ok then is im*o off ? do i have to cut im*o wire or remove im*o box?

Thanks kev

In case that you really have done this way immo off,or was able to write this ecu with kwp or galetto please post if it works....could be interestening,to know this....

if immo is off,you dont need cut anything,let all as it is,maybee you need just take out lamp of key in dash because it s possible keylamp stays on.

Regards.

[landrovertdi]

if the car does not have the body computer remove immo box

[landrovertdi]

if the car as body computer is impossible immo off with galletto o kwp , only official instrument immo off in italy euro 350,00 for immo off and 650,00 for passage soft m3 m5 ecc.

[kevfield]

I have write back to ecu with galletto in boot mode but think that is only virgin, not got car here so cant test yet,I used (clona e decode) in galletto software, but the software seem to hang when i write back to ecu but it did seem to write, when i read back in boot mode both files read differnt bit,s, all thanks to landrovertdi :)) star man

[landrovertdi]

59F for immo off I bought a specific interface.
And fantastic mlavoro and 50 seconds and finished.
For this work the cock clone is not the best.
However, if I even want to try this procedure.

[landrovertdi]

sorry , olways forget attachment

[kevfield]

how did you get this file is size 512 bytes you use differnt tool for this ???

[kevfield]

I see you must have ABRITES Commander for Fiat ??? for immo off

[landrovertdi]

which file 521kb ?
my interface no abrites
my interface italian product is very good

[kevfield]

OK can someone check see if these to files are ok i read these both in boot mode one ori and one write back with galletto

[kevfield]

i tested on car i did not work any idea,s??

[Heniugg]

Welcome
Ask for permission to download this theme information to the ECU IAW59F
Thank you very much.
Henryk

[spd_tolis]

if the car as body computer is impossible immo off with galletto o kwp , only official instrument immo off in italy euro 350,00 for immo off and 650,00 for passage soft m3 m5 ecc.


hi there,
you seem to have good knoledge!!!
do you have a link to this italian instument for 350\650 euro?
please pm it to me , if there is a problem putting it in a post....
thanks
:idea:

[1000tc]

Salutes communicate you that in Sicilia polite and good person on the IAW and other sells on eBay under the name of tuttoecu it hopes he has a strong desire to do good to attach you the link

SERIALE 59F MARELLI SCODIFICA E CAMBIO SW SENZA BOOT su eBay.it Motore, Tuning, Auto ricambi e accessori (http://cgi.ebay.it/SERIALE-59F-MARELLI-SCODIFICA-E-CAMBIO-SW-SENZA-BOOT-/170465295142?pt=Ricambi_automobili&hash=item27b085fb26)