Astra H crash data

[kevfield]

Astra H 1.7 dti 2005

TEMIC 13 188 857
9S12DG128E

Tryed with op-com but will not do it
seem,s to have to many fault,s so must do it the hard way :(

Can anyone help to remove crashdata Please

Thanks kev

[Meat-Head]

had this before, had to replace both tensioners first, if you look on the opcom forum tells you how to do it, or pay ?45 for crasheraser off ebay user beat-the-garage

[kevfield]

Ahhh i see thanks for that, i did try to clear crash with Tachosoft and less codes come back here,s what i ended up with,
B1000 - Replace Electronic Control Unit (ECU)
(39) - Present

B0084 - Invalid Data From Right EFS (Electronical Front Impact Sensor)
(71) - Present

B1000 - Electronic Control Unit Not Reusable
(56) - Present

B001B - Passenger Lap Pretensioner Circuit Open
(04) - Present

B001A - Driver Lap Pretensioner Circuit Open
(04) - Present

U2050 - Invalid Data from SOD (Seat Occupied Detection)
(73) - Present

U2050 - SOD Circuit Low Voltage (Seat Occupied Detection)
(02) - Present

Thanks kev

[juozas10]

Astra H 1.7 dti 2005

TEMIC 13 188 857
9S12DG128E

Tryed with op-com but will not do it
seem,s to have to many fault,s so must do it the hard way :(

Can anyone help to remove crashdata Please

Thanks kev

Hi.
Try...your dump cleared 100%.
Password is in your PM.
Best regards.:wink:

[z786]

dont wanna hijack the thread mate but had a 59 plate astra h yesterday, apparantly crash data has been cleared but it had loads of dtcs any one got the PROPER procedure to do it using OP-COM

these wer th codes i got

OP-COM - CAN Communication Window> 2009|Astra-H|Body|SDM (Airbag)

Read Info...
Identifier: 0x0204
VIN: W0L0AHL*********
System name: MRSZ-Temic
Part Number:13288174
Software version number: A3300RG3 V 3.4.0
Hardware key number: ??????????
Variant programming : 0x41532020202054525356394815415045
Alpha code: CA
Manufacturing date: 20090815

Total number of fault codes: 16
B1000 - Electronic Control Unit Not Reusable
(56) - Present
B0051 - Airbag Deployed
(00) - Present
B0053 - Deployment Commanded With Troublecodes in Squib Circuits Present
(00) - Present
B1325 - System Voltage Low Voltage
(03) - Not present
B0016 - Driver Curtain Airbag Squib Circuit Low Resistance
(0E) - Not present
B0019 - Passenger Airbag Squib Circuit (Stage1) Open
(04) - Not present
B0021 - Passenger Side Airbag Squib Circuit Low Resistance
(0E) - Not present
B0012 - Driver Airbag Squib Circuit (Stage1) Open
(04) - Not present
B0023 - Passenger Curtain Airbag Squib Circuit Low Resistance
(0E) - Not present
B0014 - Driver Side Airbag Squib Circuit Low Resistance
(0E) - Not present
U2116 - CAN-Bus No Communication with IPC (Instrument)
(00) - Not present
U2139 - CAN-Bus No Communication with CIM (Steering Column Module)
(00) - Not present
U2141 - CAN-Bus No Communication with REC (Rear Electrical Centre)
(00) - Not present
B1001 - Left Hand Drive/Right Hand Drive Configuration Error
(3A) - Not present
B0019 - Passenger Airbag Squib Circuit (Stage1) Low Resistance
(0E) - Not present
B1000 - Trouble Code Memory Full
(4C) - Intermittent

[Meat-Head]

donny one got the PROPER procedure to do it using OP-COM
t


1) http://www.digital-kaos.co.uk/forums/f114/opel-ecu-reset-110153/#post549416

2) if too lazy http://opcomforum.yolasite.com/resources/Opcom%20Clear%20SDM%20Deployment%20Data.pdf

[z786]

iv already tried that, no luck, has any1 actually tried it and it worked????

[lupu_sandu]

Yes. I clear crash data with op-com for over 7 cars.
Works perfectly.
PS: Use op-com 090714_EN

[carclima]

1) http://www.digital-kaos.co.uk/forums/f114/opel-ecu-reset-110153/#post549416

2) if too lazy http://opcomforum.yolasite.com/resources/Opcom%20Clear%20SDM%20Deployment%20Data.pdf


2) tested 3 times work fine always..

[z786]

wen i start activation, is it supposed 2 give me a message?
these worry me abit
B1000 - Electronic Control Unit Not Reusable
(56) - Present
B0051 - Airbag Deployed
(00) - Present

also im abit confused, can any1 hee tell me wat parts i need 2 activate by looking at the dtcs???

thanx

[f1racingmad]

i dont to make this sound as dont know what you am doing but i helped a mate repair a astra h few years ago on a 55 plate we had a simlar problem and we got fed up of changing parts make you have changed everything thats needs changing also i was told by vauxhall but the airbag control module is only good for two deployments after that it scrap it might be worth checking just in case its been deployed before.

[s5zax]

wen i start activation, is it supposed 2 give me a message?
these worry me abit
B1000 - Electronic Control Unit Not Reusable
(56) - Present
B0051 - Airbag Deployed
(00) - Present

also im abit confused, can any1 hee tell me wat parts i need 2 activate by looking at the dtcs???

thanx
There are some SDM units that crash data cannot be erazed with OPCOM or TECH 2 clear deployment record function. Last week i had an YQ ident unit. With OPCOM i had the same problem with you. After activation B1000 and B0051 cannot be cleared, so i tried with tech 2. Tech 2 showed crash data cannot be erazed - no more valid usage period. So the only option is via onboard programmer.

[emes125]

Hello,

I need pass for this dump, or better - if some of you have dump for Astra H MY 2008

[juozas10]

Hello,

I need pass for this dump, or better - if some of you have dump for Astra H MY 2008

Hi.
Please post your the original crash dump,you need fix the original dump then it will works.

Best regards.