Cummins seeded ecm

[HGV_DIAG]

hi guys. need a little help. I have a new ECM which is brand new. Its so new it has no base software in it.

I can connect to ECM but says its seeded.


How do i program this so i can recal this engine? i cant seem to find out how to do this in insite.

Thanks

[dafdiagnos]

which ecm model & which engine is it for m8?

[hercamp]

I think .....from insite and incal could be ....but I ve never try ......if its not possible with it ...I think u can get caltermIII .and try to ripp from other ecm.!!!!!!

if I am wrong some other member give u in right way.

[HGV_DIAG]

its CM850 ISBe4 from a DAF55. i have insite and incal but cannot find where the base cal is.

Thanks for your advice

[mondao]

its CM850 ISBe4 from a DAF55. i have insite and incal but cannot find where the base cal is.

Thanks for your advice


1-connect with the vehicle cummins insite
2-open the calibration menu
3-locate the calibration, find engine data (cpl, rpm, hp)
4.Registration number of the ecm
5-this works well (with engine serial number would be easier)
just try to help

[HGV_DIAG]

ok. ive been playing with this again today and have just taken a couple of screen dumps.

Ive tried 2 recent Incal discs but get the same error.

Any ideas now?

[dafdiagnos]

if ordered through daf it should have had basic parameters installed. if not i think it will need calterm or davie programming

[HGV_DIAG]

yeah thats what i thought. looks like ive got a fully blank 1 with no bootloader/base cal.

I have part of davie software with runtime / application installed but have no floppy or usb drive licence key to finish the install with dealership code on. :( i also dont have calterm yet.

[hercamp]

if ordered through daf it should have had basic parameters installed. if not i think it will need calterm or davie programming

I ve seen cummins calterm .........but u say davie????what is this stw???? :musicus:

[mondao]

ok. ive been playing with this again today and have just taken a couple of screen dumps.

Ive tried 2 recent Incal discs but get the same error.

Any ideas now?

maybe you sent a calibration which does not correspond
a closer look at engine data
disconnect (ABS)
disconnect (transmision ELECTRONIC)? maybe
data link only with the ecm
send it back, maybe you need (password authorization)
I hope to work

[rudamie]

hi guys. need a little help. I have a new ECM which is brand new. Its so new it has no base software in it.

I can connect to ECM but says its seeded.


How do i program this so i can recal this engine? i cant seem to find out how to do this in insite.

Thanks


Repair Instructions

INSITE™ 7.x ReCon? ECM Procedure:
CAUTION
To calibrate this ECM , use the following steps:


Hook up battery power
Turn keyswitch ON for 10 seconds
Turn keyswitch OFF
Launch INSITE™ 7.x
Connect
Click “OK” to ROM boot message
Select “Calibration Selection”
Choose the appropriate calibration code and transfer to ECM
Turn keyswitch ON when INSITE™ 7.x prompts

Good Luck
Dont forget to hit the thank buttom.:wink:

[MoonMagick]

Help! I'm not too clever when it comes to figuring out these automotive d/l's (I'm doing this for my BF) but I've done many others. I have Cummins 7.2 Insite but can't seem to get it to work. I would be happy to send anyone what I have and maybe someone could see what I'm doing wrong. Otherwise, my PC ID is C6DB6715...I think there is a space between the "7" and "15" but not so sure. What I come up with seems to keep being invalid.:stupido:
Thank you for any help you can offer!

[mondao]

Help! I'm not too clever when it comes to figuring out these automotive d/l's (I'm doing this for my BF) but I've done many others. I have Cummins 7.2 Insite but can't seem to get it to work. I would be happy to send anyone what I have and maybe someone could see what I'm doing wrong. Otherwise, my PC ID is C6DB6715...I think there is a space between the "7" and "15" but not so sure. What I come up with seems to keep being invalid.:stupido:
Thank you for any help you can offer!

Maybe THIS A LITTLE HELP
http://www.digital-kaos.co.uk/forums/f2/you-please-read-before-posting-1129/

[HGV_DIAG]

Thanks guys managed to sort it in the end. i reinstalled inshite on another pc and it worked a treat. I think it was summot to do with the filters, seemed to block all the cals for that engine. Anyhow all ok now :)

Cheers to all that helped anyhow

[dimitar22]

ok. ive been playing with this again today and have just taken a couple of screen dumps.

Ive tried 2 recent Incal discs but get the same error.

Any ideas now?


I have the same problem with N14 engine it is 500hp i want to reduce it, but have the same error.