Change VIN to M3 E46 Cluster.

[Cucu680]

Hello from Spain. I Have a 330ci. I changed the cluster by a M3, but it appeared the point in BC, because the VIN doesn't match that of my car.
Using the "M35080 Odometer Milleage Programmer Wipe/Reset kit ", can I change the VIN??

The gauge M3 oil temp doesn't work, and also has the m54 engine oil temp sensor.. If I edit the FSW_PSW with NCS EXpert of KMB, can I solve this??.

Can somebody help me? Thanks and sorry for my English..

[tachonow]

Hello from Spain. I Have a 330ci. I changed the cluster by a M3, but it appeared the point in BC, because the VIN doesn't match that of my car.
Using the "M35080 Odometer Milleage Programmer Wipe/Reset kit ", can I change the VIN??

The gauge M3 oil temp doesn't work, and also has the m54 engine oil temp sensor.. If I edit the FSW_PSW with NCS EXpert of KMB, can I solve this??.

Can somebody help me? Thanks and sorry for my English..
Use Pa-soft. Can do this by obd.

[Cucu680]

But only its works with cluster new uncoded? not??

this 2003 cluster bosch.

Thanks

[BATLER]

bmw 1.40 scanner is a very good tool for this!!!

[Cucu680]

bmw 1.40 scanner is a very good tool for this!!!


Thanks ;-)

[BATLER]

we are here to help each other.
regards

[pepi]

For pasoft 1.40 I dont know ,but version 1.36 cant do that 100%.I had the same problem yesterday .I did it by editing dump.

[lupu_sandu]

xprogM can edit vin in bosch dashboard on E46

[avtonega]

Read eprom in cluster, and post dump, If you haven`t OBD tool

[milanoffracing]

BMW E46 M3 have M35080 chip inside and with Pa Soft you can't change anything.

[Cucu680]

BMW E46 M3 have M35080 chip inside and with Pa Soft you can't change anything.

Because?? just buy the pasoft :-(

[Speedosoft]

Pa-soft can only help you if your dash was made by Motormeter (equipped with B58 or so called 93S66 eeproms) and not by Bosch (M35080 eeprom). The only way as already mentioned above is to read and write the eeprom directly.

[afitijuana]

post you file or lok under line 200

Regards.

[tachonow]

BMW E46 M3 have M35080 chip inside and with Pa Soft you can't change anything.
With 1.36 Ive changed VIN on E39 dash with 35080.

[milanoffracing]

With 1.36 Ive changed VIN on E39 dash with 35080.

Yes in Land of Jokes maybe ,try to change on M3 dashboard. :playingball:

[Cucu680]

thank you all. I leave you the contents of the eprom read the "bmwscanner 1.4". Could you help me and change the "VIN"? the old and wrong is JV47598 and the new right is JT64175.
The x200 line are only FF FF FF FF FF ... Could you help me?
Thanks

[Cucu680]

4A 54 64 17 50 its ok???

now could write the new file .bin with "bmw scanner in the cluster eprom"??

[PremierD]

4A 54 64 17 50 its ok???

now could write the new file .bin with "bmw scanner in the cluster eprom"??

Just write this to eeprom mate .. the same way you got the file out....(Don't know how you did it) so can't advise you on the scanner..........

[milanoffracing]

4A 54 64 17 50 its ok???

now could write the new file .bin with "bmw scanner in the cluster eprom"??


If you have M35080 in dash with bmw scanner you can't do anything try and you can see.For this one you need another programmer.:playingball:

[swingman26]

Hello, you can change your vin in bmwe46 dash with m35080 with xpro-m. Give me your dump and your vin by pm and i modify for you.

[PremierD]

Hello, you can change your vin in bmwe46 dash with m35080 with xpro-m. Give me your dump and your vin by pm and i modify for you.

Yes mate you probably can .. but it's already done and posted ........

[Cucu680]

Just write this to eeprom mate .. the same way you got the file out....(Don't know how you did it) so can't advise you on the scanner..........

thanks, but bmw scanner says: fail internal eprom checksum, conding incorrect or incomplete" ??

[PremierD]

thanks, but bmw scanner says: fail internal eprom checksum, conding incorrect or incomplete" ??

Mate are you using A scanner ... or eeprom programmer ...?

[Cucu680]

im using bmw scanner 1.40 :-(

[PremierD]

im using bmw scanner 1.40 :-(

Then mate ..you have been told by someone who knows ... it will not work ...you need to remove the eeprom and program it with the Dump I sent ...or edit the same way sorry ............

[Cucu680]

for example, does this programmer works?? BMW M35080 Odometer Mileage Programmer Wipe/Reset kit: eBay Motors (item 270585549566 end time Jun-27-10 06:16:07 PDT) (http://cgi.ebay.com/ebaymotors/BMW-M35080-Odometer-Mileage-Programmer-Wipe-Reset-kit-_W0QQcmdZViewItemQQhashZitem3f0027d2feQQitemZ27058 5549566QQptZMotorsQ5fAutomotiveQ5fTools)

[foxbox]

Hello.

Same proplem.

Some one change tacho my friends car.
330ci -01-

How i can program correct vin that tacho? Tacho is 320 capriolet -01-

I have INPA, BMW SCANNER 1.40 and chinese universal dash programmer tacho pro v2008.

Sorry my bad english... :bandit:

[martiboy]

Hello.

Same proplem.

Some one change tacho my friends car.
330ci -01-

How i can program correct vin that tacho? Tacho is 320 capriolet -01-

I have INPA, BMW SCANNER 1.40 and chinese universal dash programmer tacho pro v2008.

Sorry my bad english... :bandit:

Take a copy of your dump with the tacho pro and post here.

[foxbox]

Take a copy of your dump with the tacho pro and post here.


Open that cluster and read 35080 chip with tacho pro?
And transfer that my computer and post here? :D

Can i read dump with bmw scanner?

Thanks :congrats:

[T72]

Open that cluster and read 35080 chip with tacho pro?
And transfer that my computer and post here? :D

Can i read dump with bmw scanner?

Thanks :congrats:
pasoft has his unique format, so must do coppy in .bin

[martiboy]

Open that cluster and read 35080 chip with tacho pro?
And transfer that my computer and post here? :D

Can i read dump with bmw scanner?

Thanks :congrats:

Yes take a reading from the m35080 with your tacho pro and post your dump here with the vin that you want it changed to

[foxbox]

pasoft has his unique format, so must do coppy in .bin


Can i make this vin change at BMW scanner 1.40 at cluster where is 35080 chip?

If how i do it? How take dump? And how save it back odometer when dump is change at right vin?

Some people here says that it can not do at bmw scanner 1.40? :hmmmm2:

Please help me! :wavey:

[martiboy]

Can i make this vin change at BMW scanner 1.40 at cluster where is 35080 chip?

If how i do it? How take dump? And how save it back odometer when dump is change at right vin?

Some people here says that it can not do at bmw scanner 1.40? :hmmmm2:

Please help me! :wavey:

You have 2 kinds of equipment that you can use. I dont know about the bmw scanner but i have already said to use your tacho pro. The tacho pro manual has how to read the m35080 eeprom in it. Have a read then if you are unsure then ask again

[foxbox]

You have 2 kinds of equipment that you can use. I dont know about the bmw scanner but i have already said to use your tacho pro. The tacho pro manual has how to read the m35080 eeprom in it. Have a read then if you are unsure then ask again

Ok. Thanks i try read cluster chip at tacho pro...

But if some one know how do it at BMW scanner 1.40 please tell me :bandit: