DRS 6 and DDEC V files

[amishmafia00]

These don't get voltage, they get grounded


Does anyone know what the digital Input voltages are...we are guessing 12 volt on a 12 volt truck due to the switches on the cruise control etc. If we used one of the input to switch to an "alternate HP calibration", i.e. #1 or #2, are there any other ramifications we need to look at?

Thanks in advance.

[Thecell]

These don't get voltage, they get grounded

Perfect..Is it an isolated ground on the ecm, or can we use truck ground?

Thanks,

Bob

[amishmafia00]

it should go to the ecm/battery ground. looks like wire 953. if you go into your dddl into help, DDEC II III Iv troubleshooting, scroll almost all the way to the bottom, click on vehicle wiring schematics, click on vehicle interface harness. there are 9 pages of wiring. the link for the next page will be at the bottom of current page. sheet 5-9 shows what your looking for

[ddmech]

Bob,be sure and not put 12 volts to any inputs on the ecm.Disaster will happen friend.

[Thecell]

Bob,be sure and not put 12 volts to any inputs on the ecm.Disaster will happen friend.

Thanks for the input....so we don't :stoned::stoned::stoned: have that look on our faces after a "smoke" test.


Looking for a calibration:

06R0924978

Thanks in advance.

Bob

[Thecell]

it should go to the ecm/battery ground. looks like wire 953. if you go into your dddl into help, DDEC II III Iv troubleshooting, scroll almost all the way to the bottom, click on vehicle wiring schematics, click on vehicle interface harness. there are 9 pages of wiring. the link for the next page will be at the bottom of current page. sheet 5-9 shows what your looking for

Found it on the wiring diagram...thanks...we were just concerned that like some of the new cummins ISX ecm's that they are isolated grounds now.

[ddmech]

Any ground will work as long as it has good connection.Good luck.

[jackalfa]

Please, again I need help with calibrations for 3 trucks with DDEC V 6067MV6E 12.7L engines:

06R0948064 (original cal 445HP 1450lb-ft)
06R0946278 (original cal 455HP 1550lb-ft)
06R0856184 (original cal 430HP 1550lb-ft)

If it possible that you can help me with more torque to the maximus these engines would stand, it would be great. (maybe 1750 lb-ft). Thanks a lot and best regards.

jabkissmya, one question please: how I can find out the rating or values (HP & Torque) in the calibrations that you kindly have posted?
This because in DRS I can see the serials numbers but I don't know how to find a cross reference or can't find out the values until I calibrate them in a ECM and finally see these values when finished the calibration, sorry for maybe be so dumb...
Thanks...

[Emgo]

jabkissmya, one question please: how I can find out the rating or values (HP & Torque) in the calibrations that you kindly have posted?
This because in DRS I can see the serials numbers but I don't know how to find a cross reference or can't find out the values until I calibrate them in a ECM and finally see these values when finished the calibration, sorry for maybe be so dumb...
Thanks...

jackalfa,
I can help with the above problem. Open DRS and under tools choose create calibration, then pick out which number or numbers you to create a calibration for. You will then be asked where you want to save the calibration. These calibrations can be opened with DCT, so you don't have to load them into an ECM. I learned this on DK but I can't find the original post. The thanks go to that poster. On my computer DRS opens much faster if my USB Link is connected.

jabkissmya has provided a 630HP 1800 ft-lb calibration for an off road DDEC V. It should sill be on DK. But on road and off road DDEC V engines are very different at least on the ones I have seen. The off road engine has a DDEC IV head (which means DDEC IV style injectors) and front cover. If you can't find the calibration I can put it on mediafire.

Emgo

[Lickety Split]

jackalfa,
I can help with the above problem. Open DRS and under tools choose create calibration, then pick out which number or numbers you to create a calibration for. You will then be asked where you want to save the calibration. These calibrations can be opened with DCT, so you don't have to load them into an ECM. I learned this on DK but I can't find the original post. The thanks go to that poster. On my computer DRS opens much faster if my USB Link is connected.

jabkissmya has provided a 630HP 1800 ft-lb calibration for an off road DDEC V. It should sill be on DK. But on road and off road DDEC V engines are very different at least on the ones I have seen. The off road engine has a DDEC IV head (which means DDEC IV style injectors) and front cover. If you can't find the calibration I can put it on mediafire.

Emgo

Emgo,I wonder if jabkissmya's cal would work on a ddec IV (considering the IV style head/inj) I can provide a yahoo address if that's easier for you. Thanks,Mike.

[Emgo]

Emgo,I wonder if jabkissmya's cal would work on a ddec IV (considering the IV style head/inj) I can provide a yahoo address if that's easier for you. Thanks,Mike.

I don't think you could put a V Cal in IV ECM. DDEC V Cals have much more information in the program. I'm including links to the off road DDEC V 630 HP Cal 06R0955240. The other Cal is a 575 HP DDEC IV. As mentioned many times in related threads, these Cals probably won't make the HP without the corresponding cam, injectors, turbo and correct tuning. These Cals were provided by jabkissmya be respectful and thank him if you haven't already.

Maybe I'm wrong about the injectors being different between on and off road DDEV The off road injector #r414703007 and my on road #r414703003 the description is the same except the tip for the off road is S60 1250 flow and for on road it just 880 flow.

http://www.mediafire.com/?dnvzizgtptoi0ne
http://www.mediafire.com/?9hdyycc1fack2zr

Emgo

[Lickety Split]

I don't think you could put a V Cal in IV ECM. DDEC V Cals have much more information in the program. I'm including links to the off road DDEC V 630 HP Cal 06R0955240. The other Cal is a 575 HP DDEC IV. As mentioned many times in related threads, these Cals probably won't make the HP without the corresponding cam, injectors, turbo and correct tuning. These Cals were provided by jabkissmya be respectful and thank him if you haven't already.

Maybe I'm wrong about the injectors being different between on and off road DDEV The off road injector #r414703007 and my on road #r414703003 the description is the same except the tip for the off road is S60 1250 flow and for on road it just 880 flow.

06R0606366M575HPDDECIV.CAL (http://www.mediafire.com/?dnvzizgtptoi0ne)
06R0955240M.CAL (http://www.mediafire.com/?9hdyycc1fack2zr)

Emgo

Thanks Emgo,i am gonna grab these just to take a peek...maybe cant use the whole cal,but i might be able to use the fueling tables...right now i am running a 550hp cal at 1850ftlbs from one of our friends here on DK.
Thanks again
Mike

[makura]

Hi need cal for ddec 4 engine number 0R0523746

[jackalfa]

Hi members, I hope someone can help me with this:
there are about 5 or 6 trucks with DDEC V 6067MV6E engines, I'm trying to calibrate them with the right parameters to obtain the closest accuracy in fuel consumption: Actual Fuel Consumed vs. Electronic Fuel Consumed.
Some drivers or operators complaints, that the actual fuel consumed in tanks is not the same that the trip report reads in DDDL.
I understand that the ECM "calculates" the fuel consumption but I hope that someone can guide me how to obtain the closest real values in actual fuel consumption in the ECM trip reports.
thanks in advance. regards.

[Javidiesel]

Hi, every time I copy and paste the files to my DDRS 6.16 they desapear. I copy the files downloaded from DDC main frame from may lap top at work and paste to may DDRS at home and they works ok. Can you help me to find out what Im doing wrrong. Thank you

[Lickety Split]

Hi, every time I copy and paste the files to my DDRS 6.16 they desapear. I copy the files downloaded from DDC main frame from may lap top at work and paste to may DDRS at home and they works ok. Can you help me to find out what Im doing wrrong. Thank you

Check the file type before you save them...i.e. are they ".cal,.met,etc"
When the program looks for a file,it is looking for a certain type and only those will show. Also,make sure you are saving them in the right place...you can always change the search to all types and even tell it to look in another folder.

Sure would like to get some files for mine off of the DDC Mainframe.

Hope that helps,let us know.

Mike

[Javidiesel]

Thanks very much, I'll try it and see what happen.

[diesel88]

Dear jabkissmya (http://www.digital-kaos.co.uk/forums/members/98632-jabkissmya/)
help me cal file for
06R0694877

Thanks (http://www.digital-kaos.co.uk/forums/members/98632-jabkissmya/)

[melgarejo.salomon]

Dear jabkissmya,
I need your help with this calibrations:

06R0276076 SERIE DDEC III
06R0438381 SERIE DDEC IV

Thanks in advance and best regards.

[Javidiesel]

:party:
Hi need cal for ddec 4 engine number 0R0523746

Here is cal 06R0523746
Just copy and paste in to c/detroit diesel/DDEC Reprogram System. Good luck...

[Javidiesel]

Dear jabkissmya (http://www.digital-kaos.co.uk/forums/members/98632-jabkissmya/)
help me cal file for
06R0694877

Thanks

See post #270

[diesel88]

See post #270
My friend!

I dont find the ESN 06R0694877 in list

[QT1]

Anybody have files (calibrations) for DDC MTU, sn: 535200378; 535200381; 5352003081? Thanks for sharing

[Javidiesel]

[QUOTE=diesel88;1321687]My friend!

I dont find the ESN 06R0694877 in list[/QUOTE

???... I see the cal 06R0694877 in my system...
Try this. Connect to an ECM, open the DDRS, with it open copy the attached file in post #270 then paste in to c/detroit diesel/DDEC Reprogram System (DDRS must be open during this prosess) now go to Reprogram ECM and select from list of cals, it should be there.:listen:

[jackalfa]

Please Javidiesel, can you help me with these calibrations, DDEC V 6067MV6E 12.7L engines:

06R0948064 (original cal 445HP 1450lb-ft)
06R0946278 (original cal 455HP 1550lb-ft)
06R0856184 (original cal 430HP 1550lb-ft)

If it possible that you can help me with more torque to the maximus these engines would stand, it would be great. (maybe 1650 or 1750 lb-ft). Thanks a lot and best regards.

Thanks...

[makura]

Hi
Need help with file for engine number 06R0400556,i am having a lot of problems with this engine,either when it get worm it stops splitting the gears and remains either in low range or high all depending on where the leaver is at the time of the fault occuring.then it will start exploding like the engine will break in half.i have tried to use a few calibrations and cant seem to get it right.
I hope some one can help with the original file,this truck has smart shift.

[Javidiesel]

Please Javidiesel, can you help me with these calibrations, DDEC V 6067MV6E 12.7L engines:

06R0948064 (original cal 445HP 1450lb-ft)
06R0946278 (original cal 455HP 1550lb-ft)
06R0856184 (original cal 430HP 1550lb-ft)

If it possible that you can help me with more torque to the maximus these engines would stand, it would be great. (maybe 1650 or 1750 lb-ft). Thanks a lot and best regards.

Thanks...

Here you have cals... i just add your three cals to my system, enjoy :proud:

[gagne]

i need calibration for ddec 3 version 5.30 thanks

[Thecell]

Javadiesel,
Thanks for the serial numbers...the more the merrier !

[jackalfa]

Thanks a lot Javidiesel. best regards.

[mega357]

help me cal file for 06R0696434. Thanks

[Javidiesel]

Lickety Split (http://www.digital-kaos.co.uk/forums/members/190206-lickety-split/):

Here is your original cal for 06R0382621 without Low nox. Open it with DDCT, enjoy

[Lickety Split]

Lickety Split (http://www.digital-kaos.co.uk/forums/members/190206-lickety-split/):

Here is your original cal for 06R0382621 without Low nox. Open it with DDCT, enjoy

Thank You Sir...You are great help...Thank you.

[makura]

Still no luck with my file for engine number 06R0400556.

[topitopi]

cool job down here thanks for everything

[amishmafia00]

I need these ddec II cals

06rO14716O
06rO14716O

thank you

[mega357]

help me cal file for 06R0696434. Thanks

[Javidiesel]

help me cal file for 06R0696434. Thanks


Here DDEC Calibration requested by you and anterior posters. Enjoy:wavey:

Makura: 06RO400556

Amishmafia00: 06R0147160

Mega357: 06R0696434

[Lickety Split]

Javidiesel...do you know if it is possible to get these cals from DDC with new HP and Torque settings? or only the original settings...

Now that i have my ORIGINAL cal with the Pre Low Nox settings,(Thank You) I would like to try to get her set up for 550 or maybe even 600hp @ 1850ftlbs.
I'm at 550 now,but it's with a Low Nox cal...just wonderin'

Thanks again,you are a lifesaver...i had been looking for the pre LN cal for years.

P.S. I will compare the original cal,(the one you sent) with the one that the detroit shop put in when they rebuilt the engine to see if i can figure out what all was changed...my be of some help for anyone who cannot get a Pre Low Nox cal.

[Emgo]

Javidiesel,
when you have time I would like to get the files for the two following serial numbers.

06R0521890
06R0907034

Thanks for all the work you are doing for DK members.

Emgo

[Texas149]

I have a a ddec 4 360/430 hp serial 06r0494610 model 6067mk60. I need to bring it up to a 470 or so. This model can be turned up right?

[Javidiesel]

Javidiesel,
when you have time I would like to get the files for the two following serial numbers.

06R0521890
06R0907034

Thanks for all the work you are doing for DK members.

Emgo


Here your cals, enjoy

By chance, are you familiar with servicemaxx ? I have installed the software but I can't generate password with kg. When I insert the software ID (8FDA-6DCA) in the key generator it do nothing, I'm running it in Windows XP. Please Help. thanks:goodnight:

[Emgo]

Here your cals, enjoy

By chance, are you familiar with servicemaxx ? I have installed the software but I can't generate password with kg. When I insert the software ID (8FDA-6DCA) in the key generator it do nothing, I'm running it in Windows XP. Please Help. thanks:goodnight:

I'm sorry I don't use Servicemax, I wish I could help, you have been very helpful to me. If you haven't posted your question in the Servicemaxx thread already you may get some help there. Thanks again for the files.

Emgo

[alexcoste]

Calibration tool
upload failed calibration
the WAS file not found
(0xCDDC001D)

help with this calibration. please.
thanks

[makura]

Here DDEC Calibration requested by you and anterior posters. Enjoy:wavey:

Makura: 06RO400556

Amishmafia00: 06R0147160

Mega357: 06R0696434

Thanks mate,but this type of cal format will not work with ddrs,right only cal tool.

[mega357]

Thanks mate,but this type of cal format will not work with ddrs,right only cal tool.
You are right! And where it is possible to take for ddrs?

[diesel88]

help me the cal file for 5352001158
Thanks

[mang5087]

hello, please i need cal for 06R0995567
thanks in advance

[doloman]

Hi all. I need cal file for 06R0414549.
Thanks in advance.

[jackalfa]

Javidiesel, thanks for the great help you are providing to all members in DK.
Please did you know if it possible in 6067MV6E 12.7 engines to have more torque than 1550 lb/ft?
Did you have a calibration for 6067MV6E with 1650 lb/ft torque that you can share?
thanks in advance, regards

[SpbPirat]

Javidiesel (http://www.digital-kaos.co.uk/forums/members/276574-javidiesel/) ,please HELP ME NEED cal file for 06R0578874
Thanks

[khadang]

hi all,
please help me file calibration esn : 5262000373

this engine run only 6 injection b(right). im test injection ok not have signal control from ddec slave.
harware of ddec slave is ok and diagnostic no code.

any one can help me.
thank much advance.

[jackalfa]

Hi members I have a Freighliner 6067MK60 DDEC IV with a 470HP 1550lf-ft v32.08 calibration in the ECM, I hope some can help me with a cal with more torque than this one.

thanks in advance...

[ddmech]

The most I have seen on a factory cal for a 470 is 1550.Pm me jack and I will fix you up with something special for christmas buddy.

[fatboy63]

can anyone help with a calibration file for

06R0595366
model #6067BK60
rating group(6N4M#)=7246
Rating family(6N4D#)=7024
Application family(6N4C#)=125
EPA certification=1157
ECM serial number=Vl603WH5
ECM software level=32.08
Shared version=99
Rating version=110

using ddec reprogramming system thanks

[khadang]

hi all,
please help me file calibration esn : 5262000373 ( file .cal calibration tool )
i verry need it.

this engine run only 6 injection b(right). im test injection ok not have signal control from ddec slave.
harware of ddec slave is ok and diagnostic no code.

any one can help me.
thank much advance.

[amishmafia00]

you are running a 12 cylinder engine with 2 ecms?


hi all,
please help me file calibration esn : 5262000373

this engine run only 6 injection b(right). im test injection ok not have signal control from ddec slave.
harware of ddec slave is ok and diagnostic no code.

any one can help me.
thank much advance.

[khadang]

you are running a 12 cylinder engine with 2 ecms?

right, i try replace file calibration of s60 to ddec(slave) and run on s60 engine ok.
on s4000 engine master have pulse injection, slave no have.
no fault code, and hardware ok.

[amishmafia00]

are you looking for the file for the s4000 or are you trying to figure out why the ecm isn't working?

i

[khadang]

are you looking for the file for the s4000 or are you trying to figure out why the ecm isn't working?

i

yes this im looking.

[amishmafia00]

yes this im looking.

if you have the ecm from the other bank you could put that calibration in and change it to slave

[ricz]

Can any one help me with this calibration o6ro----946260/.

Thanks

[jackalfa]

Please,
I need help with these calibrations, DDEC V 6067MV6E 12.7L engines:

06R0960225
06R0945334
06R0946278

Calibration 06R0946278 was posted already by javidiesel (thanks again) but with 1450 lb-ft torque :bawling: , please can you help me out with 455HP and 1550lb-ft torque in all 3 calibrations? :embarassed:

Thanks in advance and the best in this New Year, regards...

[khadang]

anyone have some file for detroit diesel s2000 & s4000, please.
thank so much. im verry need them (5262000373 )

[amishmafia00]

anyone have some file for detroit diesel s2000 & s4000, please.
thank so much. im verry need them (5262000373 )

do you have one ecm with the right program in it? Do you have dct? if you have both use dct to upload program from ecm and send it to me I will change it for slave and the you can put it in your second ecm

[khadang]

i have 2 ecm.
1: ddec IV 06R0949590 sofware level is 29.5 s60
2: ddec IV 5262000373 sofware level is 31.7 12v4000
i want use ddec 2 for 1.
i converter file calibarion 29.5 to 31.7, download it with ddct and run in s60.
but the engine run not good and show error : injector respone time.
i think that cause sofware level.
im try erase blank all data this ecu to download file calibration 29.5 to ecm .but ddct can not download it.
i try whith ddrs ( i only have file download for s60). ddrs show error : wrong ecm hardware, get type "V" or "H".
i have 4 problem:
1 : how to get ecm return original . i have backup file calibration on ddct.
2 : the error injector respone time cause what? ecm sofware level or i should " injector calibraion" correct injector type for thic ecm.
3 : where i can get file calibration for esn : 5262000373.i can buy it. give me information about file V or H.
4 : have a difference of 2 ECM hardware or not?
and if i want change ecm, what should I do?

thank so much.

[khadang]

im looking ddrs download file for esn 5262000373.
please....please.....please :dancing2:

[khadang]

hi dk friend.
im need file calibration for
ddec IV 06R0949590
ddec IV 5262000373
any peope have, can shared or sale for me.
thank much advance.

[doloman]

Hi All.
I need help. cal files for 06R0710250. Pls
Thanks in advance

[ddmech]

the 2000 and 4000 have different injectors and solonoids.This is why you are getting response time codes.

[khadang]

the 2000 and 4000 have different injectors and solonoids.This is why you are getting response time codes.
thank now this ecm blank, im can't reprogram it, and cant't test jnjector calibration to fix problem.

[khadang]

hi all!
please share me file reprogram for ddec IV S4000!
thank advance.

[p455w0rd]

Hi everyone i just download all the files of the calibration they aper the DEC III IV but on the V it just show one calibration what can i do to have all the calibration DEC V thanks in advance

[amishmafia00]

hi all!
please share me file reprogram for ddec IV S4000!
thank advance.

patience grasshopper

[ddmech]

Master has spoken!LOL!

[ddtech]

hi guys im looking for a flash file for 06RE111078

THANKS

[ntgroup]

Thks anymore shared, who have DRS 6 share for anymore...Happy New Year 2012

[Elvic]

Can't start regeneration of PDF neither on the go nor during parking. Could anybody give a piece of advice about how to switch off this system? Now ECU has an active error and it continually stops the engine :(

[ddmech]

Make sure you clutch release switch an parking brake switch are working and the ecm and dddl are reading them.

[jackalfa]

Hi jabkissmya & Javidiesel,

we really miss you great help to this tread, please when you have time friends, please take a look at the requests. :)

best regards...

[ntgroup]

Please,
I need help with these calibrations, DDEC V 06R0765514 12.7L Version 3.0engines:
I verry need....Thank Advence

[diesel88]

hi
mang5087 06R0995567
doloman 06R0414549
SpbPirat 06R0578874
fatboy 06R0595366
ricz o6ro946260
jackalfa 06R0960225
06R0945334
06R0946278
khadang 06R0949590
5262000373
ddtech 06RE111078

[Emgo]

When someone gets a chance I need the cal and unit files to use with DRS for the two following serial numbers.

06R0521890
06R0907034

I got the cal file from Javidesel for DCT but I need the files to use with DRS. I'm in no hurry.

Thanks,

Emgo

[torqueman]

Hi,
Can sombody please upload calibration for ddecIV non egr with 470-500 hp.6067PK.
Be very thankful to him.

[detroit747]

here ya go.

this one is 500hp for a ddec IV non egr from australia

[ddtech]

can i please get cal file for 06R0419327 thanks

[ntgroup]

Master, when you have time I would like to get the files for the three following serial numbers.

06R0768517
06R746369
06R0724492

thanks in advance

[whalla]

does anyone have calibration for ddec3 11.1L series60

[khadang]

thank you so much diesel88.
can help me file calibration for this engine: 5262000436
thank advance.

[alitasdepollo]

Thank you very much for sharing these files comrades! have helped me a lot! greetings!.

[detroit747]

think someone was looking for a 500hp 12.7litre cal not sure if this is ddec IV or III

also its australian with no egr

[geekgt]

Master, can you help me with this engine number?
06R0046628

[elslow]

can someone help me with calibration for 06R0294030
THANK YOU IN ADVANCE

[diagnosss]

can you help me with this serial numbers

06r0723951
06r0408167

[amishmafia00]

Does a calibration exist for ddecV NonEgr industrial?

[hercamp]

yes , its like the one that post a m8 before with aust programing, non egr non vgt turbo , just u need turn on industrial settings ,u can use that one .

[harobaua]

Hi all, I thank anyone who owns this calibration for detroit IV.

Engine Series: Series 60 (12.7 L)
Engine Serial Number: 06R0821465
Engine Model: 6067MK62

If possible, 450 HP to 500 HP.
Original comes up to 430hp. A 2110 RPM.
Thanks, :proud:

[raphael]

hi folks, can somebody to post the calibration for ddecv serial engine 06R0886441 THANKS!!!!!!

[jackalfa]

Hi all, I thank anyone who owns this calibration for detroit IV.

Engine Series: Series 60 (12.7 L)
Engine Serial Number: 06R0821465
Engine Model: 6067MK62

If possible, 450 HP to 500 HP.
Original comes up to 430hp. A 2110 RPM.
Thanks, :proud:

So the 6067MK62 means (62) No EGR, correct?

Please, I need one like this one too:
6067MK62
v32.01
original: 430HP 1450lb-ft

I need it with more torque maybe 1550 lb-ft or 1650 lb-ft

Thanks

[jackalfa]

What could happen if I made a calibration using split and joint taken the info Rating0 with more HP and Torque from another 12.7L, but instead MK use PK or BK 12.7L?

Thanks in advance.

[Attach]

help me with the following "calibrations" please:

Unite#06RE120350
MODEL#6067BK60

Thanks in advanced.

Cherrs..

[harobaua]

So the 6067MK62 means (62) No EGR, correct?
Yes

Please, I need one like this one too:
6067MK62
v32.01
original: 430HP 1450lb-ft

I need it with more torque maybe 1550 lb-ft or 1650 lb-ft
I too need with more Torque 1650LB

Thanks

Thanks ... !!!

[whalla]

help needed . i neeeeeeeeed calibraion for 11.1 ddce2 ecm for high torque and horsepower ecm serial 6067wu60

[chewin]

Hi, I need file for unit 06r0608994

thanks

[jackalfa]

Please, somebody can help me with a calibration for a 6067MK62 v32.01 with 1550 lb-ft or 1650 lb-ft?
(if it's in Cal Tools form, no problem as long is a software v32)
thanks

[carlos mata]

please 06R0430488 calibration

[autotuning]

Hi
i was told i had posted this in the wrong section so her it is again.

Hi all
can anyone please help me with the files for the following ecm please,

The engine serial I have is 06R0968125
ENGINE MODEL 6067HK62
This is a 14.0L 500bhp 2110 rpm

Thanks in advance.

[crazy60]

Please, somebody can help me with a calibration for a 6067MK62 v32.01 with 1550 lb-ft or 1650 lb-ft?
(if it's in Cal Tools form, no problem as long is a software v32)
thanks
you can take any cal version and convert it to match your ecm software, take a 39.6 cal and on convert cal tell it to convert and select your met file, I have taken a 14 liter ddec 4 cal 32.6 and converted it to 5.30 to run in high rpm 3 software, dont need a new cal just modify yours, or send it to me and I'll jack it up. Search for pw_f under name, and change it to 1.1, thats 10% more fuel, now search air_temp_of, you get air_temp_offset_boi, set all above 10dg cel to 31.75, that sets timing to max. those 2 simple changes will make your day

[fenomenoide04]

Hi, I have an engine ddec III with ecm software version 4 when I diagnose with DDDL this have 2 codes:

code 53: nonvolatil memory data incorrect

This code show twice time.

Somebody tell me how to correct this trouble??

thnks for advanced.

[Emgo]

Hi, I have an engine ddec III with ecm software version 4 when I diagnose with DDDL this have 2 codes:

code 53: nonvolatil memory data incorrect

This code show twice time.

Somebody tell me how to correct this trouble??

thnks for advanced.
I just did some work for you, take a look at this thread
http://www.digital-kaos.co.uk/forums/f152/ddec-iii-iv-repair-tips-198149/index2.html

Emgo

[crazy60]

nonvolatile memory means ecm on the way out, probably will no longer hold mileage, speed etc. may want to get one ready, I see a lot of requests for cals for particular units, just curious reason, wanting something modified, fresh box? if need modified for something shoot it to me and tell me exactly what you want out of it can probably do. don't sweat the version guys, just convert the cal to the level you need, i have taken level 32, 34 and 39 and went backwards to level 9 for a ddec 3, just open your cal, tell it convert and pick the met file for the level you need. realy its that easy!:cheers:

[Emgo]

If I have a Cal from a 2 stroke DDEC II ECM is possible to put in a DDEC II ECM from a series 60? Is possible to put that same 2 stroke Cal in a DDEC III or IV ECM?

Thanks,
Emgo

[crazy60]

I think yes you can, had 2 ecms, 49 and 50, what 2 stroke are you working on, 6 or 8V?

[Emgo]

I think yes you can, had 2 ecms, 49 and 50, what 2 stroke are you working on, 6 or 8V?

It's a 6V92 and the guy wants a spare ECM programmed and ready to install. There's only one DDEC II Metafile here on DK and I was curious if it's possible to put a Cal from a 2 stroke DDEC II in a Series 60 DDEC II ECM or maybe even a DDEC III or IV ECM. If it's possible to use a III or IV ECM I know a harness adapter kit would be required.

Emgo

[juanch]

:giveup:I need a ecm programmed to work with electronic transmicion I can do with the DDRs? thanks

[amishmafia00]

autoshift? can be done with dct

[joesmith8888]

Hi, I have an engine ddec III with ecm software version 4 when I diagnose with DDDL this have 2 codes:

code 53: nonvolatil memory data incorrect

This code show twice time.

Somebody tell me how to correct this trouble??

thnks for advanced.



I've had this code pop on before on ddec3 ecm. I found if I reflashed the ecm to software level 9 fixed the problem for a while.

[ddmech]

You can try a reflash and that might do it.
If not and the truck runs good without issues I
would be too concernerd.Some say that the ecm
is going out but from experience I have seen this
many times and run for years.If the codes is the only
issue I would lose any sleep over it.

[Thecell]

Cheers m8s,

Looking for:

06R0621236

Thanks All, especially CRAZY60 for your insight on these systems.

Cheers,

TC

[Thecell]

Never Mind...figured out how to download the calibration directly from the ECM. Worked perfectly!

Thanks anyhow.

[alexmamun]

hi everyone i need file for
06R0813137 calibration file please
thankx

[hackmexicano]

you may need to upgrade to a newer version of drs depending on which one you have, so i have included drs 6.16

just extract folder to c:\detroit diesel and copy/merge/overwright files as needed.

when you run drs it will tell you it is being upgraded and shut back down, this is just giving you the new server updates to install new ecm versions. Click program, if truck does not have a matching serial to whats on you list, it will let you select from a list what you want to program and you should see all serials you listed plus 06R1999999. this is the turbo actuator program for use with dddl 6.44 and higher. save all accumulated data before programming. as it might loose all accumulated data during reprogram.

THANKS!!!:thrasher:

[alexmamun]

hi anyone can help me out please i need file for
06R0813137 calibration file or flush file
thankx

[sssigor]

please calibrate
Engine Series 60
Engine Serial # 06R0605891
VIN 1FUJAHCG61LH77562
thanks in advance

[crazy60]

to all on cal requests, if you have dct you should be able to upload it from the ecm. if you dont you really need to get it! best tool yet, for bench reprogram you need J-42766 for ddec3 and 4. dont have the 5 handy

[cholmes729]

to all on cal requests, if you have dct you should be able to upload it from the ecm. if you dont you really need to get it! best tool yet, for bench reprogram you need J-42766 for ddec3 and 4. dont have the handych


Im working on making a bench programmer harness, its not hard, I will post up the part numbers.

[nudelpaso]

hello, I hope I can help gauge a DDEC IV engine, but I codes were not as active and away, believe that if I try another calibration work. agradecere response

[mcdeal]

hello any one have the programs to reprogram a detroit ecm.and please tell me what one i will need thanks i need help on this one thanks to all

[Thecell]

HELP, Looking for calibration for:

06R0790910

DDEC V ECM version 3.01

On site right now and can't do a change.

Don't seem to have the right MET file...

Thoughts?

Thanks m8s.

[saican]

Hi,
Please help me i need calibration file for 06R0960715 I need to remove password from the ECM am using DDCT.
Thanks

[ntgroup]

hj all friends

i need file flash 06R0526247, 06R0773171
Thks

[Gear head]

Ive installed this but it turns right off as soon as you try to run program windows xp sp3

[torqueman]

Can somebody please help me with ecm calibration file for 06R0871680 with software level 3.01, model 6067HV6E.

Thanxxxxxxxx in advance.

[bigfredz]

Thanks for the download. i cannot open program says ot lisenced or missing key can you help Thank YOU!!!

[anih3n]

Works very fine on Win7 Home Premium X64!!!!

Thanks for share!!!!

DK rules!

[anih3n]

This are the cracks for DRS!
http://dl.dropbox.com/u/86304029/DDRScracks.rar

[crazy60]

for password use text editor, once you place it on your screen you can drag and drop the password into it and change to what you want, default is always 0000

[trehlebov]

This are the cracks for DRS!
http://dl.dropbox.com/u/86304029/DDRScracks.rar

How to use this crack?

[SpbPirat]

for the collection, i download today......

[Emgo]

Here's a Calibration from a DDEC II 8V92TA 450 HP RH

[autotuning]

Can Anyone help me with these Cal files please
06R0866041
06R0900867
06R0968125
06R1026294
06R10001284 ? IS this a valid number or has someone made a mistake?

Many Thanks in advance

[alexmamun]

i m looking 06R0581953 calibration dec IV Please help me out

[bigfredz]

This are the cracks for DRS!
http://dl.dropbox.com/u/86304029/DDRScracks.rar
... i saved files how do i run these files. plz help Thanks

[amishmafia00]

Does anyone have series 50g or 60g files for ddrs? I thought I had gotten some here but when I looked i couldn't find any

Thanks

[aaronmtz]

please anybody know how to disable the engine brake or can i have a calibration for 11.1L 330hp whit not engine brake

[ddmech]

I use dct,but I think you can do it with drs friend.

[Poptest]

Please share calibration for:

VIN# IHSRKD2R6NH409267
ENGINE DDEC3-S60.12.7L
ENGINE SN: 06R0053768
ENGINE MODEL: 6067WK60

Thank you....

[carlos mata]

help 06R0377128 please thanks

[trehlebov]

We have Freightliner with Mersrdes-Benz engine 350 hp. I want to calibrate it for get more power. Is it possible?
model MBE 460
sn 46090600743186

[Juanincho]

Hi, someone can help with 06R0467255 6063TK35 (Genset application)

Thanks in advance !

[crazy60]

turn off jakes in the input outputs. cal compare will show easy

[carlosramospoma]

hi
mang5087 06R0995567
doloman 06R0414549
SpbPirat 06R0578874
fatboy 06R0595366
ricz o6ro946260
jackalfa 06R0960225
06R0945334
06R0946278
khadang 06R0949590
5262000373
ddtech 06RE111078
hello friend please can you help with calibration for the DRS for Detroit Series 60 decIV 12 liters O6R1036641 IV engine number one 500HP 1650 lbs Torque

[crazy60]

you have 500 1650 in the cal, need to use rating change with hand held or drs to set to the 500,

[tdftruckin]

HERE IS MY DDEC V CAL, EGR REMOVED.

I AM WORKING ON IMPROVEMENTS, BUT THIS WILL GET YOU GOING. (NEED DDCT TO PROGRAM IT)

[tdftruckin]

hello friend please can you help with calibration for the DRS for Detroit Series 60 decIV 12 liters O6R1036641 IV engine number one 500HP 1650 lbs Torque


HERE IS AN EXCELLENT STOCK CAL. NEED DDCT THOUGH.

[tdftruckin]

please anybody know how to disable the engine brake or can i have a calibration for 11.1L 330hp whit not engine brake

I'M 99% THIS ONE DOES NOT HAVE JAKES. IT IS A 365HP CAL. HOPE THAT'S CLOSE ENOUGH TO HELP :)

[parezoo]

I will get an ECM with egr and dpf removed, but i dont know how to download the calibration (calterm or insite???) so we can then use it on another ecm, if you can tell me how step by step, i will do it and share it here....

[sptecnico82]

I will get an ECM with egr and dpf removed, but i dont know how to download the calibration (calterm or insite???) so we can then use it on another ecm, if you can tell me how step by step, i will do it and share it here....

Calterm and Insite are for cummins. Here only Detroit my friend. But if you want to help, use dct (detroit calibration tool). :driver:

[tdftruckin]

is anyone able to get the stock cal for 06r0728699 ?

[dalsib]

help me please. I very need cal file for
6067MV6E
06R0842097

Thanks

[alexmamun]

hi everyone anyone can help me out with ddec IV non egr calibrations file for this engine series number 06R0715941 PLEASE
THANKX

[SaMirakle]

HERE IS MY DDEC V CAL, EGR REMOVED.

I AM WORKING ON IMPROVEMENTS, BUT THIS WILL GET YOU GOING. (NEED DDCT TO PROGRAM IT)

I downloaded this cal file onto a DDEC V engine yesterday and it was terrible. DO NOT USE AS IS. The power was decreased and it was derated. This cal file is NOT recommended for use as is. It still needs a lot of work.

[tdftruckin]

I downloaded this cal file onto a DDEC V engine yesterday and it was terrible. DO NOT USE AS IS. The power was decreased and it was derated. This cal file is NOT recommended for use as is. It still needs a lot of work.

That Cal is the 515hp turned up 14%, and torque up to 1800 ft-lbs. No EGR. I wan that for over a year, bought the Nexiq because I wanted to tweak more for fuel mileage.

If you really had problems check your I/O. The only way for that cal to cause a de-rate would be you didn't change all the i/o to match. Or if you did and you added The VNT or or EGR Valve Outputs back in to that cal.

Also- If you are not changing the turbo, you have to manually set the position of that VNT.

I have made a few changes, and am going to run this adaptation for awhile, (see attached) Ive gotten good numbers out of it.

Long and the short of it, there is nothing wrong with the cal, the current is a little better, but if think just a cal will make your EGR worries dissapear, well not gonna happen. I have two Owner operators leased to me that I just manually set their VNT, My truck (where the cals come from) has a new Exhaust manifold and normal turbo but i spent an extra $4000 for them.

And a note on the original cal - The guy that took EGR out of my engine to begin with has more happy paying customers than you have posts my friend. He can't ride around in your truck for 2 months to tweak every little item to perfection (thus why I bought the box) I send people to him constantly and recommend his work. I helped out 2 guys leased to me otherwise i'm only working on my truck, I'm not in the diesel dr business, i'm in the trucking business. I've gotten good info and software here and have tryed to give back what I have.

So if you are really having trouble with it ask, before you assume it's no good. I'll be happy to help you get it working properly!

[SaMirakle]

That Cal is the 515hp turned up 14%, and torque up to 1800 ft-lbs. No EGR. I wan that for over a year, bought the Nexiq because I wanted to tweak more for fuel mileage.

If you really had problems check your I/O. The only way for that cal to cause a de-rate would be you didn't change all the i/o to match. Or if you did and you added The VNT or or EGR Valve Outputs back in to that cal.

Also- If you are not changing the turbo, you have to manually set the position of that VNT.

I have made a few changes, and am going to run this adaptation for awhile, (see attached) Ive gotten good numbers out of it.

Long and the short of it, there is nothing wrong with the cal, the current is a little better, but if think just a cal will make your EGR worries dissapear, well not gonna happen. I have two Owner operators leased to me that I just manually set their VNT, My truck (where the cals come from) has a new Exhaust manifold and normal turbo but i spent an extra $4000 for them.

And a note on the original cal - The guy that took EGR out of my engine to begin with has more happy paying customers than you have posts my friend. He can't ride around in your truck for 2 months to tweak every little item to perfection (thus why I bought the box) I send people to him constantly and recommend his work. I helped out 2 guys leased to me otherwise i'm only working on my truck, I'm not in the diesel dr business, i'm in the trucking business. I've gotten good info and software here and have tryed to give back what I have.

So if you are really having trouble with it ask, before you assume it's no good. I'll be happy to help you get it working properly!

Thanks for the response! Yeah, I didn't have time to do any tweaking so basically I just threw the calibration on their and wasn't able to set the truck's I/O settings. It was for a customer that wanted an uprate and I was just testing your cal file out first to see how it performed. I guess it doesn't work that easily on Detroits like the EGR delete works on the ISX's.

Anyway, I appreciate the current file you've just posted and I'll see what I can do with it next time a DDEC V comes around. I may just have to end look into borrowing one for a day from a local truck shop or something.

[jackalfa]

Please someone can share a calibration for a Series 50 engine 6047TK60 with engine brakes on it?

Thanks in advance.

[rebel127]

Do you have a serial# of one with jakes?

[whalla]

hello to all i am looking for a calibration for a ddec3 ecm to run on a ddec2 engine

[donniemnemonic]

Hi m8.

Got a truck that is coming into the shop today that had an automatic transmission replaced by a manual tranny. The problem is that the owner complains of low power output (truck not pulling its weight). I know with cummins engines this can be solved with a recalibration of the engine ecu to exclude auto transmission features in the ecm program and changing to the appropriate gear box transmission ratios. Is this the same with detroits or do I just have to disable the automatic transmission features I/O without the need for recalibration? The engine serial number is 06R0574998 so if some1 could post a suitable calibration for this without the auto-transmission feature I would be most appreciative...

Regards
Donniemnemonic

[ddmech]

Donnie,
No,the detroit is nothing like cummins.It doesnt matter about the setting,they should stiil pull 100%.Make sure the vss is reading inthe ecm.Many times the auto and manual have different config.If not reading in ecm may be throwing a vss derate.

[trehlebov]

Hi m8.

Got a truck that is coming into the shop today that had an automatic transmission replaced by a manual tranny. The problem is that the owner complains of low power output (truck not pulling its weight). I know with cummins engines this can be solved with a recalibration of the engine ecu to exclude auto transmission features in the ecm program and changing to the appropriate gear box transmission ratios. Is this the same with detroits or do I just have to disable the automatic transmission features I/O without the need for recalibration? The engine serial number is 06R0574998 so if some1 could post a suitable calibration for this without the auto-transmission feature I would be most appreciative...

Regards
Donniemnemonic

you need DDRS and change auto-trans to manual in customer parameters

[donniemnemonic]

Hi m8s

Thanks for the help. is that all I need to do? Change the parameter to manual transmission and make sure my VSS signal is present?

Regards
Donniemnemonic

[ddmech]

That is the best places to start with friend.

[amishmafia00]

Use ddrs to change ecm for manual transmission, it's easier. if the vss is not working it will limit rpm. I just did 2 of these. the vss wiring is usually up ontop of the trans tied up and capped off. just get the right vss and plug it in.

[trehlebov]

see wiring shematic in DDDL to conect VSS to ECU. And change in DDRS auto to manual

[skodafelicia]

That Cal is the 515hp turned up 14%, and torque up to 1800 ft-lbs. No EGR. I wan that for over a year, bought the Nexiq because I wanted to tweak more for fuel mileage.

If you really had problems check your I/O. The only way for that cal to cause a de-rate would be you didn't change all the i/o to match. Or if you did and you added The VNT or or EGR Valve Outputs back in to that cal.

Also- If you are not changing the turbo, you have to manually set the position of that VNT.

I have made a few changes, and am going to run this adaptation for awhile, (see attached) Ive gotten good numbers out of it.

Long and the short of it, there is nothing wrong with the cal, the current is a little better, but if think just a cal will make your EGR worries dissapear, well not gonna happen. I have two Owner operators leased to me that I just manually set their VNT, My truck (where the cals come from) has a new Exhaust manifold and normal turbo but i spent an extra $4000 for them.

And a note on the original cal - The guy that took EGR out of my engine to begin with has more happy paying customers than you have posts my friend. He can't ride around in your truck for 2 months to tweak every little item to perfection (thus why I bought the box) I send people to him constantly and recommend his work. I helped out 2 guys leased to me otherwise i'm only working on my truck, I'm not in the diesel dr business, i'm in the trucking business. I've gotten good info and software here and have tryed to give back what I have.

So if you are really having trouble with it ask, before you assume it's no good. I'll be happy to help you get it working properly!

Can you please
Need to adjust the VGT? How much pressure put on what speed?
tnx


and another problem when opening calibration DDEC5 - in attach

[crazy60]

your met file didnt match, when you go to open it will ask for a match, when you look for the match it will tell you the version at the top of the file open box

[tmcbroo]

hey guy newbie and a truck driver here trying to get a calibration for my engine 12.7 6067gk60 ser o6r0217052 it had a ddec 3 computer but it was damaged cannot get cal off it i got a used ddec 4 of another truck same engine model but has no power my calibration was 485/470 cruise and pedal i would like a upgrade to 500 but at this point i need the right calibration for the engine, any help would be great.

[tdftruckin]

Can you please
Need to adjust the VGT? How much pressure put on what speed?
tnx


and another problem when opening calibration DDEC5 - in attach


Setting the VNT requires some mechanical knowledge. Also, it would be easier to just remove the VNT turbo and install a regular non waste gated turbo and be done with it. If you manually set the VNT turbo, you have to adjust it as you increase altitude (mountains).

you need ddec v release 3 metafile, i have attached to this message.

[ddmech]

If you replace vnt with stock turbo you will not have much low rpm boost friend.

[skodafelicia]

Setting the VNT requires some mechanical knowledge. Also, it would be easier to just remove the VNT turbo and install a regular non waste gated turbo and be done with it. If you manually set the VNT turbo, you have to adjust it as you increase altitude (mountains).

To adjust the VGT on DDECV with EGR enough already understood as doing.
Maybe soon I will try to ride with DDDL and record logs - then it is clear that much will turn

you need ddec v release 3 metafile, i have attached to this message.
tnx

[tdftruckin]

If you replace vnt with stock turbo you will not have much low rpm boost friend.

very true, but dial back the table in the smoke limited torque (see the cal I posted) and it will fuel at the low rpms, thus building boost. The stock turbo can be set up for high performance, but then I always lost atlease 1 MPG at road cruising speed due to backpressure it creates. Maybe that's just my engine...

[khadang]

hi dk friend!
can help me file calibrarion engine : 5352003087.
thank so much advance!

[chamberlain31]

i have noticed on several ddec v files that the fudge factors wasn't the normal 1.0 like the non egr detroits. i have seen them anywhere from 18% to 23% over, but they still only get roughly 420hp to the ground. whats the deal with this?? are they just using this to cover a low hp fault??

[shisik]

please help files 06R0970679 & 06R0969866

[parin]

can someone post calibration file for 06r0888517 please thanks

[crazy60]

you have different inj and turbo than the 500 cal, so be careful what you ask as this could get ugly for u on cylinders, what is serial of new box u have?

[donniemnemonic]

Hi m8s

Could someone kindly post ddec v calibration for engine serial number 06R0854991.

Regards
Donniemnemonic

[jackalfa]

Hi members, I hope I'm not in the wrong thread.
Anyone knows why an ecm do not keep the settings in DDEC Data after sending the change to the ecm?
It seems that the ecm do not have activated this settings, but after trying to activate this setting the ecm don't keep the changes. When I turn on and off ignition the ecm don't keep the changes, the ecm don't save reports. thanks.

[tmcbroo]

hey guy newbie and a truck driver here trying to get a calibration for my engine 12.7 6067gk60 ser o6r0217052 it had a ddec 3 computer but it was damaged cannot get cal off it i got a used ddec 4 of another truck same engine model but has no power my calibration was 485/470 cruise and pedal i would like a upgrade to 500 but at this point i need the right calibration for the engine, any help would be great.

[raphael]

hi, some body knows, how to activate the multiplex j1922 in a ecm ddec iv??? the old ecm is burn, but i get a new ecm ddec iv, but i cant activate the multiplex for comunicate whit a VECU VOLVO
the esn is 06R0665931
the vin is 4V4NC9RHX2N319505
thank you in advance

[khadang]

hello all.
please help me file calibration for detroit engine no: 06r0297548
thanks verry much advance!

[Wayne64SS]

Here's a Calibration from a DDEC II 8V92TA 450 HP RH

Hey man do you have the metafiles for this thing? I need this cal but there are no meta files with it so I can't open it.

Thanks,
Wayne

[Emgo]

This should be the correct Metafile for DDEC II


Emgo

[Wayne64SS]

188553

So i've decided that having to copy the cal and unit files every time you open the DDRS 6 program was too cumbersome. I've created a batch file that you can just point your DDRS 6 shortcut at and it will open the program and do the copy automatically. You will have to edit / create directories as necessary for this to work because your computer is probably a little different from mine. What I did was go into C:\Detroit Diesel\ and create a new folder there called DDRS Cals. (c:\Detroit Diesel\DDRS Cals) Then inside that I created 2 more folders, 1 called Cal and the other called Unit. Just unzip all the calibrations you download from here into those folders. You'll notice I've attached a Test1.txt file as well. This file is what the batch program uses to do the copy. Put it in the newly created C:\Detroit Diesel\DDRS Cals\Cal folder and forget about it. The batch won't work without it being there. It's pretty self explanatory though, so I'm sure you guys won't have any trouble!!!

Thanks for everything!

[Wayne64SS]

Can anyone provide me with a registration code for DDCT 4.5 with computer ID: DU22306818 this is probably the wrong thread but i don't know where to ask since the DCT thread is gone.

[mrgrinch]

in need a cal file and meta file for 06r0160193, thank you, any help is appreciated.

[Z71]

In need a cal file and meta file for 06R0878454, with egr please programming error
thank you, any help is appreciated.

[hercamp]

there say ddrs, thats mean 7x vrcion, but thats not the right folder where server download the flash.
is just to others that will try on ddc6 up ..and will find nothing .

a very good bat file , thnx

[Idocode]

Hello dear friends! I have a problem with DRS(((( It opens fine but there's no software available, and when it's try to connect to the server requests the password, I enter 0000 and get the error "Unknown User ID - Please check APPID in Option" P.S. In option ID is:ACF2 Dealer code:0000 and Branch Code:0000
Please tell me what am I doing wrong? I really need to be able to raise DDEC software level((((
Thank you, any help is appreciated.

[bnolann]

you have to have account with detroit server

[Idocode]

you have to have account with detroit server

I'm understood... and please tell me how to get the account, you need to sign a contract with the detroit or how else can? The problem is that I'm from Russia, and here the problem is the dealers from Detroit ..

[Idocode]

Maybe anybody have *.prg files for DDEC IV/V??? Or how downloading firmware from flash eeprom? Anybody do it before? Please help advice? really want to learn, these DDEC, had already studied all the stuffing and learned to repair. To be happy, I need to learn how to programing them.. Thanks in advance to those who respond!))))
Sorry about my english))))

[ddmech]

Use drs and cals posted throughout thi threadfriend.

Just out of curiosity,does anyone know why all the thanks counters are reset to zero?

[Idocode]

I'm use ddct and know how change calibrations but I have some of ECUs which needs to upload software and I have ddrs all version which not legal and havn't access to DD server. Question: how get access to server or where search firmware files for ddrs (not cals)?? Thanks responded...))

[parin]

Hello, any one have 550hp and 1850tq calibration to share for ddec 5 please thanks

[parin]

I called Freighliner Dealer to set up account with DDRS and Server is 2600$ 1 year subscription.

[crazy60]

Hello, any one have 550hp and 1850tq calibration to share for ddec 5 please thanks
No ddec5 with 550 on egr, only 515 with 1650

[anthonycorsi]

Maybe anybody have *.prg files for DDEC IV/V??? Or how downloading firmware from flash eeprom? Anybody do it before? Please help advice? really want to learn, these DDEC, had already studied all the stuffing and learned to repair. To be happy, I need to learn how to programing them.. Thanks in advance to those who respond!))))
Sorry about my english))))

I have a trick to download prg to ECM ddec3/4 set serial ddec5 in drs and then select to install it will try to program ECM and start downloading the prg and later it set and error because is not the correct ECM soft level, next you can use cal tools to modify the cal installed In ecm


Sent from my iPhone using Tapatalk 2

[Wayne64SS]

I"m looking for calibration for serial # 06D0308814 Thanks in advance!!!

[amishmafia00]

I have a trick to download prg to ECM ddec3/4 set serial ddec5 in drs and then select to install it will try to program ECM and start downloading the prg and later it set and error because is not the correct ECM soft level, next you can use cal tools to modify the cal installed In ecm


Sent from my iPhone using Tapatalk 2

You do this then you are able to modify the prg with cal tools?

[parin]

Hey, any one know is there bench calibration cable for ddec 5 and ddec 4-3 if any one know the part number please let me know. Parts department does not know what bench calibration cable is..

[Emgo]

Hey, any one know is there bench calibration cable for ddec 5 and ddec 4-3 if any one know the part number please let me know. Parts department does not know what bench calibration cable is..

I think you'll have to make your own. Read this thread http://www.digital-kaos.co.uk/forums/f166/bench-cables-cat-cummins-detroit-210082/

Emgo

[parin]

No ddec5 with 550 on egr, only 515 with 1650

You sure about this ? customer said that the dealer could do 600hp for him.

[Z71]

Yes DDEC5 with no egr 550 with 1850, 600 with 1850, 700 with 1850 with 3000 rpm et ect ect, the crazy machine lolll

[tdftruckin]

hi, some body knows, how to activate the multiplex j1922 in a ecm ddec iv??? the old ecm is burn, but i get a new ecm ddec iv, but i cant activate the multiplex for comunicate whit a VECU VOLVO
the esn is 06R0665931
the vin is 4V4NC9RHX2N319505
thank you in advance

Use cal tool and compare with this one I just pulled. it's a 99 volvo ddec4 rel32d i have not looked through it but if you compare with the one you are working with you will find the i/o config.195397

[tdftruckin]

You sure about this ? customer said that the dealer could do 600hp for him.

you can do whatever yo want, however you won't find 550 in a stock cal for the US anyway. You will have to edit the actual cal.

[bullrider]

you may need to upgrade to a newer version of drs depending on which one you have, so i have included drs 6.16

just extract folder to c:\detroit diesel and copy/merge/overwright files as needed.

when you run drs it will tell you it is being upgraded and shut back down, this is just giving you the new server updates to install new ecm versions. Click program, if truck does not have a matching serial to whats on you list, it will let you select from a list what you want to program and you should see all serials you listed plus 06R1999999. this is the turbo actuator program for use with dddl 6.44 and higher. save all accumulated data before programming. as it might loose all accumulated data during reprogram.

i installed the program succesfully, but when i run it a message pops up says ( can not find root in directory) what am i doing wrong?

please help.
thank you all.

[bullrider]

please guys i'm still stuck.

[anthonycorsi]

You do this then you are able to modify the prg with cal tools?


Yes, when the ecm is loaded with base program calibration tools could load any calibration file you want, but is the ECM is blank you will receive an error window.


Sent from my iPhone using Tapatalk 2

[anthonycorsi]

No ddec5 with 550 on egr, only 515 with 1650

You can modify the fuel map with calibration tool and set a greater pulsewith to the injector in the rpm you like but you have to know what your are doing because you could get and old Mack calibration instead of get more power is you extract the .cal file a can help you to get more power, it's not enough change rating horsepower setting you have to set a new pulsewith in order to get more torque or horsepower, it's depends in what point of the curve you set a larger pw.

I post a picture to explain better what I want to say195968195969

If you raise at 1200 you get more torque, but if you raise a 1800 or more you get more power, but if you raise more than 3 points you get black smoke because you have to modify turbo settings to get more volume of air inside the combustion chamber and more air cooling to increase air density. Best ways to accomplish this is put the truck in a Dyno and start to modify the injection curve.

If I help you hit thanks ***128521;


Sent from my iPhone using Tapatalk 2

[anthonycorsi]

Yes DDEC5 with no egr 550 with 1850, 600 with 1850, 700 with 1850 with 3000 rpm et ect ect, the crazy machine lolll

I think you want to blow up your engine if you hit 3000rpm, the crankshaft shell can't stand that speed without turning or you can broke a connecting rod because touch acceleration in the piston


Sent from my iPhone using Tapatalk 2

[anthonycorsi]

hi, some body knows, how to activate the multiplex j1922 in a ecm ddec iv??? the old ecm is burn, but i get a new ecm ddec iv, but i cant activate the multiplex for comunicate whit a VECU VOLVO
the esn is 06R0665931
the vin is 4V4NC9RHX2N319505
thank you in advance

J1922 is always active in ddec3 and ddec4 calibration but if you want to check see in calibration tool //shared/io configuration/ serial communication
But I think that the j1922 datalink only work communicate with auto trans and abs, the cluster and other cab interface work with j1587/j1708 if it and old truck or j1939 if it a newer system195974



Sent from my iPhone using Tapatalk 2

[Wayne64SS]

I"m looking for calibration for serial # 06D0308814 Thanks in advance!!!

BUMP. Can anyone get this cal for me? Thank you.

[kwagga]

Do any body have DDCT.HLP files

Is there a way to cal a 16V4000 IV ecm to rev up like a cat 793 truck does if it idles to long .
I raised the idle speed by 100 rpm because we pulled 5 engines due to the cam followers that do not get enough oil. Hours on engines where between 5000-8000 hrs.
To much idle time

[Z71]

Yesterday afternoon after preparing the truck running and the engine running 3000 rpm and this on the supervision of our mecano working a week on Detroit Diesel and he told me that could have up to 3200 without a problem, and have is has made 900 hp with turbo and special calibration and 2-3 small secret thing done by me and even upload a video you will by the end of next week because tomorrow night (Monday) have returned to a small adjustment. DDEC V 515hp no egr with a turbo buildup special for him, and ca or moves the wind and not a few close friends

[hercamp]

good to know all that , but u test engine?? how much tons per min gives the turbo? you engine at 3000 rpm most runn up to 1000hp i guess, post a video,thats will be great.

[amishmafia00]

I want to change prg. prg is not the same as cal

[carlos mata]

please calibration serie 60 06r0394599

[jackalfa]

Carlos, you can re-program the ECM with a cal from the same engine model then with DCT change engine serial number. Use first DDRS then DCT.

[juanjo]

Hello sorry to bother you, I wanted to ask if you know how to re-program a ddec v ecm the ecm by suppressing egr, download a calibration tool for use with lime but not how to do it with this program, thank you very much to help me
have a good day

[bigfredz]

I had a vehicle with same issue. Original trans was a I thinks it's called a rockella or something like that. (Semi auto) auto shifts were controlled by engine ecm. Then a full manual trans was installed. Using ddrs I changed inputs and outputs to no function which for trans shifting gear. And still would get active faults for ess low gear etc... Could the change needed to be done with deyroit cal tool. I had to contact factory to make a new cal and reflash ECM. Plz advise thnx

[tmcbroo]

hey all, here been reading post for weeks going to try some programming, first i'm looking for calibration for
12.7 l
6067gk60
o6r0217052
it was on a ddec 3 computer but i need the calibration for a ddec 4 computer still looking for a good thanks in advance, please helpi have been waiting for months for this cal.....

[carlos mata]

pleace calibration 06R0603517 thanks

[mory lanes]

if I select another DDEC V ECM accept but mark me error at the end of the process and it is noteworthy that not a DDEC V ECM if not a DDEC III do not understand why this happens:
207703207704207705207706207707

[mory lanes]

DDCT try it and I mark the following but not if this well my process is all that I can do all this off:
207708207709

[duhuu]

hello.
I need my friends help file for ddecIII
06RE106166.
Thank you very much

[Underpsi]

Could I get the calibration file for 06R0326108
Thanks

[Z71]

Engine serial number
06R1999999

[jackalfa]

Please I need help with a cal http://www.digital-kaos.co.uk/forums/f166/dct-users-316992/index2.html#post2068836

[jackalfa]

Please, DK members I need your help with a calibration for a 6V92 8067-7B28 engine, serial number 06VF173XXX DDEC II Automotive RH Rotation.
The file can be in calibration tools or DRS format.
Thanks in advance.

[jackalfa]

Sorry members to keep asking, please if someone has a calibration for an engine model 8067-7B28 6V92 DDEC II it would be greatly appreciated.

[ddmech]

Sorry friend,cant do you any good.Those are few and far between for the 92.

[jackalfa]

Thanks ddmech, I appreciate you time friend, it's hard to find it, I'm even looking for a bus in my area to with a similar ECM to copy just the calibration with DCT but no luck. But I someone come across one it would be great... thanks again.

[Emgo]

Sorry members to keep asking, please if someone has a calibration for an engine model 8067-7B28 6V92 DDEC II it would be greatly appreciated.

I have a calibration from a RH 8V92 DDEC II if would help any. Let me know

[amishmafia00]

Hello guys, It's been a while but i'm still here! I need a calibration for a volvo with a DDECIV engine. I am programing an ecm without having the original and need to make sure that the inputs and outputs are right. This unit is supposed to ship out tomorrow so I don't have alot of time
Thanks Everyone!

[raphael]

ddec IV calibration for volvo
I need a calibration for a volvo with a DDECIV engine. do you have one you could send me?
Thank you


hi, i have calibrations, but send me your engine serial number 06R0....... or engine model 6067GK, MK60, MK62?????

[raphael]

if I select another DDEC V ECM accept but mark me error at the end of the process and it is noteworthy that not a DDEC V ECM if not a DDEC III do not understand why this happens:
207703207704207705207706207707
the ecm is damage!!! failure the eeprom, flash code 53 fmi12 right? or is seeded??. you can not program this ecm, need replace the eeprom x28hc256 plcc32

[raphael]

ddec IV calibration for volvo
I need a calibration for a volvo with a DDECIV engine. do you have one you could send me?
Thank you

send me your engne serial number, o engine model

[amishmafia00]

engine model is 6067bk60 but any calibration from a volvo will give me what I need. All I want to do is look at the inputs and outputs to make sure I have them right.

[Underpsi]

Anyone able to help me out with the stock cal file for 06R0326108 thanks