autocom cdp

[Alex79]

In china there is two factory that make CDP and from mine experience three different CDP interfaces :
1. Working OK
2. With bad OKI chip for ford ( sometimes without that chip )
3. The one with orange relays ( that one is worst ) if that don't work from start , don't waste time to repair

And there is others problems like bad soldering and low quality components . It is very hard to bye good quality ( matter of fortune ) !
If you get defective CDP try to return that , sometimes it looks easy to repair but in most cases repairs are not successful !
Pay attention from where are you buying .

[Alex79]

On my clone stands SAB-C167CS-LM chip and working perfect , tested on BMW cars


can you make good quality picture of the main board and relay pbc please?

Don't know how to upload picture , sent me your mail on PM !

[oep]

Alex79 & bestb use ImageShack® - Online Photo and Video Hosting (http://www.imageshack.us/)
then put links here.

Am also interested to see which is this pcb that works with bmw.
So far we gona 2x 390r and 2x si for changing but this does not work on clones i got and several guys here.

thanks

[michalez]

http://img215.imageshack.us/img215/79/zdjh.th.jpg (http://img215.imageshack.us/i/zdjh.jpg/)
http://img337.imageshack.us/img337/8628/zdj2y.th.jpg (http://img337.imageshack.us/i/zdj2y.jpg/)

[scooby99]

Hello All

Looking for a bit of help

Got autocom gold box > put delphi 2011.3 (2.11.3) on pc vista .plug box into pc red light comes on .

Got the delphi fileactivation file back puts it in >goes to pc picks ..vci connection >usb/bt ..com24 (vcp)


Then go to test ... failed> go to update ...

possible problem

1 pc cable not connected to pc > but get redlight on the box?

2 power cable not connected to tester

3 selected com port not available

am lost >>

cheers

scooby99

[michalez]

have you connected to the car? if not do it :)

[Alex79]

http://imageshack.us/photo/my-images/534/dsc08782mi.jpg/

http://img4.imageshack.us/img4/7161/dsc08784bl.jpg
http://imageshack.us/photo/my-images/534/dsc08782mi.jpg/

[Alex79]

http://img215.imageshack.us/img215/79/zdjh.th.jpg (http://img215.imageshack.us/i/zdjh.jpg/)
http://img337.imageshack.us/img337/8628/zdj2y.th.jpg (http://img337.imageshack.us/i/zdj2y.jpg/)
Your is identical like mine !

Did your works on all cars without problems ?

[michalez]

till day yes :) Bmw works good. But china supplier erase chip name :) nobody press thanks :((

[scooby99]

Hello All

Okay tried it in car still same problem 'cant find the device
but red light still stays on >

some pictures of the board

cheers

scooby99

[Alex79]

Hello All

Okay tried it in car still same problem 'cant find the device
but red light still stays on >

some pictures of the board

cheers

scooby99
Are you trying connection with USB or bluetooth ?

[meteor80]

Hello All

Okay tried it in car still same problem 'cant find the device
but red light still stays on >

some pictures of the board

cheers

scooby99

Once I had problem with bluetooth.
Try to desolder that.

[psyxaz]

Hi,
maybe someone can PM me, if advertising is banned, a link where to buy working Autocom? That works with Ford and BMW? Thank You very much

[elchip]

Hi,
maybe someone can PM me, if advertising is banned, a link where to buy working Autocom? That works with Ford and BMW? Thank You very much

Any can do all brand's only need fix error's on PCB ...
I maked fix on my and work all brand's

[bestb]

I change the 2 IC`s and 2 resistors and still not working with BMW so the problem must be with something else...

[cosmind]

with bmw problem is on relay pcb, relays are ok, must be 1 of the relay drivers

[oep]

cosmind is right.. the problem is in relay pcb.
elchip have you repaired this pcb? any info?


thanks

[alfy]

I change the 2 IC`s and 2 resistors and still not working with BMW so the problem must be with something else...

If the 2 ICs and 2 resistors fix don't work, the next fault to search is on rellays and rellay drivers.

For me 80% problem IC and resistors, 20% rellays.
On one of mine, found faulty both IC + resistors and rellay driver!
I have one 100% working rellay board and one 100% working main board, so I can swap and test on others and locate the problem easier.

[elchip]

with bmw problem is on relay pcb, relays are ok, must be 1 of the relay drivers


cosmind is right.. the problem is in relay pcb.
elchip have you repaired this pcb? any info?


thanks


If the 2 ICs and 2 resistors fix don't work, the next fault to search is on rellays and rellay drivers.

For me 80% problem IC and resistors, 20% rellays.
On one of mine, found faulty both IC + resistors and rellay driver!
I have one 100% working rellay board and one 100% working main board, so I can swap and test on others and locate the problem easier.



Yes u need swap K-line chip's also put 560 ohm on place pullup of SI9241 ( chinese put or 3.9 or 39 ohm hehehe )

Look to replace MAX chip's on relay board and if Ford not work get new OKI chip.
After all that you will have full working CDP .

I was also replaced all capacitor's on PCB - electrolitic ..

All I buy from FARNELL EXPORT and no more problem.

Regard's

[oep]

I'll test this tonight elchip and get results here... i got some bmw ecu's in office.

[elchip]

I'll test this tonight elchip and get results here... i got some bmw ecu's in office.
You can put any resistor to K-line pullup frpm 470 ohm up to 1 Kohm .... It is standard K-line only multiplex by relay board. Main problem is to chinese put false manufactured part's ...
They start to copy all include chip's , resistor's and all ..
Can you image to I was find cloned chip atmega162 in VCDS china it is not same dimension HIGH as normal and have different signature quality ...
Also in CDP Pro I was finded FTDI232BL china maked and 93C46 which was just blow ...

hehehe

[alfy]

Yes u need swap K-line chip's also put 560 ohm on place pullup of SI9241 ( chinese put or 3.9 or 39 ohm hehehe )

Look to replace MAX chip's on relay board and if Ford not work get new OKI chip.
After all that you will have full working CDP .

I was also replaced all capacitor's on PCB - electrolitic ..

All I buy from FARNELL EXPORT and no more problem.

Regard's

Where on farnell have you found OKI and MAX chip?
I can't find theme, maybe I'm blind... :)

[elchip]

Where on farnell have you found OKI and MAX chip?
I can't find theme, maybe I'm blind... :)
Google is your best friend...
No more finish solution on DK ...
Tomorrow will coming all from china what is here writed.

I push you to right direction that is enough I think.

[nikauto]

has someone problems with autocom on bmw 2005???

[alfy]

Google is your best friend...
No more finish solution on DK ...
Tomorrow will coming all from china what is here writed.

I push you to right direction that is enough I think.

Searched FARNELL but no chips.
I bought MAX from RS-components. I didn't foud OKI anywhere for now.

[bestb]

Yes u need swap K-line chip's also put 560 ohm on place pullup of SI9241 ( chinese put or 3.9 or 39 ohm hehehe )

Look to replace MAX chip's on relay board and if Ford not work get new OKI chip.
After all that you will have full working CDP .

I was also replaced all capacitor's on PCB - electrolitic ..

All I buy from FARNELL EXPORT and no more problem.

Regard's
So what to do put the 560 OHM resistor instead of 390 ?:hmmmm2:

[oep]

Puted 681r, its not working, how ever i see 1k kline vs +12 at si, ususaly i put 681r.
tried to correct this but no luck. still bmw not working.
however, e60 ecu connected via e46 ok, and x83 also ok.

[oliver123]

hi i hawe a question about autocom :
not work on pre obd (-2000)(blouetooth not work)
cars and 2001 ford tranzit engine (abs srs work)work on peugeot boxer 2008 ; fiat ducato 2007;volvo v40 2001(petrol);bmw x5 2003(diesel);fiat punto 2003;opel vectra c 2006;ford tranzit 2008
i attach some pictures any solution ? thanks

[scooby99]

Hi

Alex i tried it with usd cable and got no joy> tried 20011.3 on a vista pc >then tried 2011.1 on xp but both dont work ... am lost as to what it is thats wrong

who has a working autocom on 2011.3

cheers

scooby99

[elchip]

So what to do put the 560 OHM resistor instead of 390 ?:hmmmm2:
Maybe many of peoples here dont know anything about of electronic in base !
I didn't say to 560 ohm help in your problem's ...
At first look datasheet of SI9241 chip's and find base of working environment and component values , next learn what is pullup resistor and how staff work IS)9141 HW ...
Next if all is OK on board chip's OK , after you test all and stile not work check relay's and relays driver's if all is ok after scope measurement of command signal's to MAX chip's command's and all other than maybe you have problem in FW in your tool.
I am not here to learn someone electronic for that need's peoples was innovated school for electronic or you need self learn from book's and internet and for that you need a couple of year with extra good practice !

And for last why give someone finished solution on forum for that expensive tool to tomorrow same solution CHINA manufacturer grab that and use ...
Look to scaremistake LEXIA solution today every CHINA DVD which coming with CLONE tool have his solution for offline update ...
Did Chinese pay him for that ?
NOOOOOOOO NEVER
So I say Autocom Clone tool can be fixed 100% and work very good and by the way it is the best universal diagnose in last many year whic I was get for small amount of money - for me is better than KTS 520 tool and that is for me I never say to it must be also for you or any user ...
Regard;'s

[nkstyle]

hi i hawe a question about autocom :
not work on pre obd (-2000)(blouetooth not work)
cars and 2001 ford tranzit engine (abs srs work)work on peugeot boxer 2008 ; fiat ducato 2007;volvo v40 2001(petrol);bmw x5 2003(diesel);fiat punto 2003;opel vectra c 2006;ford tranzit 2008
i attach some pictures any solution ? thanks

Hello
I have the same PCB and problem.

Bluetooth not working.

Does anyone know what is the bluetooth model soldered on the main board of the original VCI?

[mechanior]

so it looks original cdppro may be useful to someone and describe individual elements for future repairs will have instructions with pictures103665

103666

103667

103668

103669

[mechanior]

part 2103670

103671

103672

103673

103674

[mechanior]

part 3103676

103677

103678

103679

103680

[mechanior]

part 4103682

103683

103684

103685

103686

[mechanior]

part 5103687

103688

103689

103690

103691

[baner]

part 5103687



Seem that this original has even older revision of PCB - rev. 3.0:motz:,
novadays all chinese clones have "cloned" newer rev 3.2 of PCB, but anyway, thanks for pictures!

Regards and respect!:wavey:

[Harrycz44]

Hello,
I try connect
BMW E60 year 2005 DDE.5.0 and do not work all system.
Mercedes A 170 CDI year 1999 find all ecu and work fine.
Ford Mondeo 2.0 TDci year 2003 not find engine ecu and immo, all ecu as abs, clima, instrument yes...

[bestb]

Hello,
I try connect
BMW E60 year 2005 DDE.5.0 and do not work all system.
Mercedes A 170 CDI year 1999 find all ecu and work fine.
Ford Mondeo 2.0 TDci year 2003 not find engine ecu and immo, all ecu as abs, clima, instrument yes...

So if is not working with Ford maybe is the IC that someone mention few weeks ago about Ford...

I need to try....

[Harrycz44]

So if is not working with Ford maybe is the IC that someone mention few weeks ago about Ford...

I need to try....

Dont work only with ecu engine and immo, another ecu yes...

[Meat-Head]

another ecu yes...

Are you the man from Del Monte?

[cracoucass]

hello mates
i saw on another forum thzt there s a keygen
to make autocom clones work with the 3/2011 version
but the guy who gives activation is not ready to share..

[brandy-p]

hello mates
i saw on another forum thzt there s a keygen
to make autocom clones work with the 3/2011 version
but the guy who gives activation is not ready to share..

Since he wrote this program (keygen).

[Harrycz44]

Are you the man from Del Monte?

Hello What is it Del Monte?:hmmmm:

[Harrycz44]

Hello I open my cdp becouse do not read ford engine ecu. And missing here OKI IC.. it is normal?? ths

[autocargo]

Should have been there...I suggest you contact your seller to sort it out.

[baner]

Hello I open my cdp becouse do not read ford engine ecu. And missing here OKI IC.. it is normal?? ths

Look, same here:



(autocom cars, arrived last week from china)

Rumors are that down there in China is shortage of OKI chips, and that factory just decide to omit it from PCB.:stupid:

Becouse there is two or three factories which makes Autocom, this is confirmed just for one which make CARS wersion, seems that TRUCKS version is still with OKI:stupid:.

Regards and respect!;)

[Harrycz44]

Look, same here:



(autocom cars, arrived last week from china)

Rumors are that down there in China is shortage of OKI chips, and that factory just decide to omit it from PCB.:stupid:

Becouse there is two or three factories which makes Autocom, this is confirmed just for one which make CARS wersion, seems that TRUCKS version is still with OKI:stupid:.

Regards and respect!;)

When missing this IC OKI what car can not read?? Now I have problem with Ford mondeo 2.0 TDCi year 2003 dont read engine ecu.

[dimitar]

Fcuking yelllow .......... That ic costs 0.0001$ for a mil.pieces

[vwpassat]

Is that available for heavy trucks?
What is the best for European Heavy trucks?

can you share with solution how to activate 2011/3? without internet?

here is autocom2011/3 for all people , for password pm me

[thunder2]

Hi mans.
I have some probleme with my CDP,no chip in board,rsssss
I need autocom 2011/3

Tks to all

[vwpassat]

So, at your experience, Autocom is well for all trucks, or not?
Iveco Man Volvo Scania Isuzu Iveco Daily, Caterpilar ?

Are you the man from Del Monte?

[baner]

So, at your experience, Autocom is well for all trucks, or not?
Iveco Man Volvo Scania Isuzu Iveco Daily, Caterpilar ?

FYI, does NOT working with VOLVO heavy duty, any kind. Tried on few FH, FH16, Volvo bus chasis. Not conectinig message "Vehicle does not respond" is all you got.:stupid:

Also does not work with Renault trucks within Volvo group (DCI DXI). Not checked with Renault e-tech:afraid:.

Also does not work with chinese cables on IVECO. Even does not power up VCI interface.

MAN, Mercedes, DAF are (mostly) OK:top:.

So I would say, fifty-fifty. But for that price is not bad!

Regards and respect.;)

[baner]

When missing this IC OKI what car can not read?? Now I have problem with Ford mondeo 2.0 TDCi year 2003 dont read engine ecu.

That OKI is for FORD PWM protocol, so you may guess, it will not work for all FORDs whiich use this protocol. That are mostl europian Fords until MY 2005, I think:afraid:.

Regards and respect!:top:

[alfy]

I can confirm, that now in AUTOCOM CARS there is missing OKI chip!
All prodicers don't have OKI chip, becose they can't find it on the market...
Seems like TRUCK version is "old stock" and have OKI inside, eaven don't need OKI in TRUCK...

So if you need to diagnose FORD cars, don't buy it right now and wait till OKI will be available again (rumors say next month).

[oliver123]

on my pcb i have oki chip
but ford doesen't work(abs airbag does ; engine not)
and pre obd cars doesen't work

[Harrycz44]

Know anybody type OKI chip. I want buy it and repair CDP
M6636B?

[solar]

Yes,its true Autocom makers in China cant find chip for Fords...try to order one,but they answer,Autocom out of stock,because cant find chips for Ford protocol:)

[VTS_Tibi]

Other than the sometimes missing OKI IC are these Autocoms the same? I mean, are there quality differences between the 2-3 clone tool manufacturers? As price wise there is quite a difference between suppliers, and naturally for them all tools are "high quality"....

If so, which one is the best to buy? (and where from...)

[elchip]

Other than the sometimes missing OKI IC are these Autocoms the same? I mean, are there quality differences between the 2-3 clone tool manufacturers? As price wise there is quite a difference between suppliers, and naturally for them all tools are "high quality"....

If so, which one is the best to buy? (and where from...)

There is no one good and complete CDP from china on market ...

[meteor80]

I have bought 4 pieces from Acartool via Aliexpress and everything was fine, but now there are no autocom's on stock.
Once I have bought from other place and of course Ford doesn't work.

I need to order another one so we will se is with quality still OK.

[elchip]

I have bought 4 pieces from Acartool via Aliexpress and everything was fine, but now there are no autocom's on stock.
Once I have bought from other place and of course Ford doesn't work.

I need to order another one so we will se is with quality still OK.

All was work 100% ?

I think you didn't test all protocol's ...
I can bid with you to on market is no full OK CDP CLONE and never was ...

regard's

[meteor80]

I have one piece and everything works file till now.
Ford, bmw, vag, psa, honda, toyota, suzuki, opel, nissan, renault, fia
It didn't connect with Honda Jazz- first model, but with others hondas works fine.

[victor2k]

Hello,
Anyone used Autocom CDP on Audi/VW cars for clearing the fault memory ?
I used on VW Golf 4 /1.4 /2001 year for reading faults,then the fauls was erased and the wonderfull 65535 fault code was after that.With VCDS this fault code can't be readed,but Autocom will read and can't be cleared anymore.

[meteor80]

I saw that.
I think that is some bug in Autocom application.
After 65535 there are no faults stored.

[makadam]

Autocom 2011 fails to connect to engine on Astra X12XE and X17DTL (2000). Other modules work fine (ABS, Instrument, Airbag). Also unit work with Fiat Seicento VAN 2009, and BMW 320D E46 (1999) all modules. I'am using 2011 1 version. Has anyone sucsefully connected to OPEL with that engine?
I think that my autocom K line is Ok because on some vechile work and they are using K line for comunication. Do I need to change 2 chips, and also resostors are 30 Ohms (30R0)?

Pics from AUTOCOM

http://img825.imageshack.us/img825/3780/39350250.jpg (http://imageshack.us/photo/my-images/825/39350250.jpg/)

http://img9.imageshack.us/img9/1225/33661152.jpg (http://imageshack.us/photo/my-images/9/33661152.jpg/)

[neonlee]

I'm on the midst to reverse enginering autocom s/w hopefully can come out the keygen for 2011_3 :)

[bazare]

I have an Autocom that is not working on K-line.
Replaced both resistors with 3900ohm and both K-line chips. I still have same problems. When I connect it only to the car I have 2 red LED instead of only 1 red 1 green. Replaced all 74HCxxx gates and the Atiny but same problem. It's working ok on CAN
Anyone have a sugestion?

[cosmind]

have you replaced SI9241AEY K-line transceiver ?

[bestb]

anyone looking for OKI chip try to find MSM6636B instead of OKI.

By the way I just order autocom but is without OKI chip but the good news is that is works with BMW.

[alfy]

anyone looking for OKI chip try to find MSM6636B instead of OKI.

By the way I just order autocom but is without OKI chip but the good news is that is works with BMW.

On what BMW have you try?

[Ashraf6119]

On what BMW have you try?

I think clone Autocom work on BMW up to E46..........But, it will not work on E60, E80, E90 and so on................I mean any thing up to 2003 it would be OK.........but, more than 2003/4 you got to be lucky.............

Last week I did also notice one other thing was on Ford Fiesta 2006 1.4 Petrol when I plugged Auto-con into OBD 16 pin plug it kept blowing Fuse for Ignition Switch Fuse # F30, 15amp..........has any one come across like this before...........:questionmark:

[obdmaster]

I think clone Autocom work on BMW up to E46..........But, it will not work on E60, E80, E90 and so on................I mean any thing up to 2003 it would be OK.........but, more than 2003/4 you got to be lucky.............

Last week I did also notice one other thing was on Ford Fiesta 2006 1.4 Petrol when I plugged Auto-con into OBD 16 pin plug it kept blowing Fuse for Ignition Switch Fuse # F30, 15amp..........has any one come across like this before...........:questionmark:

My autocom works well on bmw E60 and E90 m8

[looly]

My autocom works well on bmw E60 and E90 m8
Have u had to replace any components inside it?

[obdmaster]

Have u had to replace any components inside it?


No straight from china on one of autocom threads i uploaded loads of pics of pcb,s

[alfy]

I think clone Autocom work on BMW up to E46..........But, it will not work on E60, E80, E90 and so on................I mean any thing up to 2003 it would be OK.........but, more than 2003/4 you got to be lucky.............

Last week I did also notice one other thing was on Ford Fiesta 2006 1.4 Petrol when I plugged Auto-con into OBD 16 pin plug it kept blowing Fuse for Ignition Switch Fuse # F30, 15amp..........has any one come across like this before...........:questionmark:


My autocom works well on bmw E60 and E90 m8

Mine work also NOW on BMW E60 and E90 and some others that won't from new...

[PierreTheron]

My Autocom also works on all BMW i tried .

Only had problem with some new Nissans.

[bestb]

On what BMW have you try?

e91 2005

but I have another CDP with oki chip old stock - not working with BMW

[xdamdamx]

Hi, I have a problem after update to 2011.3. After
intallation and activation it says that i need to update the
VCI firmware. It goes OK, but after this CDP connects to car without problem, but when i click "Read fault codes" i get message "VCI not found" . The weird thing is that "live data" work almost everytime OK.

anyone had this problem and resolved somehow?

If i downgrade back to 2011.1 it works OK.

regards, damdam

[lupu_sandu]

You connect to internet with autocom opened.
Open autocom, deactivate, uninstall, reboot, install again, activate off-line and enjoy.
DO NOT CONNECT to internet and open autocom.

[xdamdamx]

Thanks lupu_sandu, will try your solution in the morning. When i get it working, i should turn off internet connection everytime i start CDP?

[autocargo]

Is there a a .bat file or anybody knows what host file we need to create? I want to stop autocom connecting to theirs servers, just like the solution for VCDS.

Regards

[Ashraf6119]

Is there a a .bat file or anybody knows what host file we need to create? I want to stop autocom connecting to theirs servers, just like the solution for VCDS.

Regards

Try this and see if it helps.................

INSTRUCTIONS TO BLOCK COMMUNICATION WITH ACTIVATION SERVER:

NOTE: Hosts is the name of the hosts file and not another directory name. It does not have an extension (extensions are the .exe, .txt, .doc, etc. endings to filenames)

XP / VISTA / SEVEN (You need administrator privileges to edit the files, which takes an extra step than being an administrator account)

Assuming you are an administrator account when you are logged in:
1) open Notepad by right clicking on the application icon and choosing run as administrator. If you don't run Notepad as administrator, you won't be able to edit hosts file

2) open the hosts file in Notepad. The hosts file is located in:
C:\Windows\System32\drivers\etc or if your system hard drive isn't C: the path is whatever your system path would be: %systemroot%\Windows\System32\drivers\etc

Add the following line :

127.0.0.1 activation.autocom.se

Save the file as hosts and your change will instantly be active.

[lupu_sandu]

Or just run this bat file (run as administrator on Vista/Seven):

[Marek_Spy]

were I buy M6636B ? have good seller ?

[bochen]

were I buy M6636B ? have good seller ?
OKI chip is hard to buy, but you can find one in T300 key programmer.

[Marek_Spy]

I find in china . But schipping is expensive

[cosmind]

replaced max4820 in autocom with no comunication on BMW 2005-2007 and now waiting for cars to test.

[Marek_Spy]

I think that it would be good to do list of bugs and gather it together . What do you think?

[algarcia]

Hi ,

I ?ve just got this unit, with cables. Anyone knows how to test a Nissan Primera 2000 with a 14 pin connector? The unit did not include this testing cable. any help will be appreciated.

algarcia

[Ashraf6119]

Hi ,

I ?ve just got this unit, with cables. Anyone knows how to test a Nissan Primera 2000 with a 14 pin connector? The unit did not include this testing cable. any help will be appreciated.

algarcia

Autocom don't include Nissan 14 Pin Cable..........Unless you buy your self and test it...........

Nissan 14Pin to 16PIN Diagnostic Cable Connector | eBay (http://www.ebay.co.uk/itm/Nissan-14Pin-16PIN-Diagnostic-Cable-Connector-/130657392749?pt=UK_Diagnostic_Tools_Equipment&hash=item1e6bc9986d)

But you should know that Autocom do not Support Nissan 14 pin more then just the Engine ECU System to Diagnose

[alfy]

replaced max4820 in autocom with no comunication on BMW 2005-2007 and now waiting for cars to test.

Many times changing MAX is not enough...

Try this:

mesure, how many rellays are ON when in "stand by", so all connected, sw opened and tyr to connect to eny car (no need for a real car!) and then back to sw main - here measure rellay coil and see how meny are ON.

If 2, sorry no BMW
If 3, you have good chanse, that works on BMW...

[DiagnosBoy]

Can someone help me with activation if i post the fileactivation file

[baner]

Many times changing MAX is not enough...

Try this:

mesure, how many rellays are ON when in "stand by", so all connected, sw opened and tyr to connect to eny car (no need for a real car!) and then back to sw main - here measure rellay coil and see how meny are ON.

If 2, sorry no BMW
If 3, you have good chanse, that works on BMW...

Very interesting, can you please be a litlle bit more specific:giveup:?

There is 20 relays on relay board, which 3 must be on?

Did you mean that we must oopen sofware, choose BMW on cars menu (even with VCI which is not connected to real car), then try to communicate with car, and AFTER THAT (regardless if VCI was or was not connected to real car) THERE MUST BE 3 relays still active (ON)?:heeeelllllooooo:

Regards and respect!:bounce:

[vergel]

Autocom 2011 fails to connect to engine on Astra X12XE and X17DTL (2000). Other modules work fine (ABS, Instrument, Airbag). Also unit work with Fiat Seicento VAN 2009, and BMW 320D E46 (1999) all modules. I'am using 2011 1 version. Has anyone sucsefully connected to OPEL with that engine?
I think that my autocom K line is Ok because on some vechile work and they are using K line for comunication. Do I need to change 2 chips, and also resostors are 30 Ohms (30R0)?

Pics from AUTOCOM

http://img825.imageshack.us/img825/3780/39350250.jpg (http://imageshack.us/photo/my-images/825/39350250.jpg/)

http://img9.imageshack.us/img9/1225/33661152.jpg (http://imageshack.us/photo/my-images/9/33661152.jpg/)

I have also this kind of PCB(exactly the same) cannot connect to Opel Astra G Z16xe. it can connect to airbag,ABS,Instrument, infotainment. but for engine ecu , communication failed. any idea what is the problem?

This autocom has arrived with 9241a ic and resistor with 30R0, but for testing I replace again the two IC and two resistor with 390 ohms but the problem still the same not connected to opel ECU, any idea what is this problem

[cosmind]

Many times changing MAX is not enough...

Try this:

mesure, how many rellays are ON when in "stand by", so all connected, sw opened and tyr to connect to eny car (no need for a real car!) and then back to sw main - here measure rellay coil and see how meny are ON.

If 2, sorry no BMW
If 3, you have good chanse, that works on BMW...

in standby I have 2 relays ON
on BMW E90 2006 I have 4 relays ON : 2 relays ON from standby, 1 relay for obd pin 1 and 1 relay for obd pin 7 and 15

schematic with contact of relays up and relays down
on and off are relays

off off off off
off off on off
off off on off
off off off off
on off off on


maybe I'm wrong but 90% I think that this is relays ON
on is also on in standby

edit: I checked also on good autocom, same relays are ON, maybe problem are slow or fast initialization for kwp2000
tryed on sirius32 on bench, on kwp2000, and comunication is ok

who can donate an BMW ECU with kwp comunication ?

[alfy]

in standby I have 2 relays ON
on BMW E90 2006 I have 4 relays ON : 2 relays ON from standby, 1 relay for obd pin 1 and 1 relay for obd pin 7 and 15

schematic with contact of relays up and relays down
on and off are relays

off off off off
off off off off
off off on off
off off on off
on off off on


maybe I'm wrong but 90% I think that this is relays ON
on is also on in standby

edit: I checked also on good autocom, same relays are ON, maybe problem are slow or fast initialization for kwp2000
tryed on sirius32 on bench, on kwp2000, and comunication is ok

who can donate an BMW ECU with kwp comunication ?

I think you have like this in stand by (looking from the bottom):

off off off off
off off on off
off off off off
off off off off
off off off on

Check again.

[bestb]

Hi
I have 2 autocoms one working with BMW other one not.
I changed the relay boards and still working... but when I changed main PCB it stop. So that means the problem is with the main board not on relay PCB.
I noticed that IC close to usb port are different one board has ATMLH124 second board (good one) 93LC4681.

I also checked all resistors on both PCB all the same ....
Thats I done so far...

[Marek_Spy]

See exactly what are the differences between the PCB may be the solution to the problem of communication with BMW

[bestb]

Thats Im looking for.. but I need help from you guys
Maybe people who got working Autocom with BMW can check what type of IC is on the board?

[Marek_Spy]

I can not help you I have not BMW

[cosmind]

I think you have like this in stand by (looking from the bottom):

off off off off
off off on off
off off off off
off off off off
off off off on

Check again.

red is on in standby
green is on for BMW

[obd.tech]

keep up the good work on finding a fix for this guys.

whats the reason some fords (k-line?) do not work?....is it the OKI chip missing?

obd

[autocargo]

If you have OKI chip on board you can check R74 and R75 if there is not 390 ohm then replace. It worked for me ;)

[alfy]

red is on in standby
green is on for BMW


Yes, missing one...

[alfy]

Hi
I have 2 autocoms one working with BMW other one not.
I changed the relay boards and still working... but when I changed main PCB it stop. So that means the problem is with the main board not on relay PCB.
I noticed that IC close to usb port are different one board has ATMLH124 second board (good one) 93LC4681.

I also checked all resistors on both PCB all the same ....
Thats I done so far...

Yes, some has problem on main PCB, but most on rellay.

[bestb]

Maybe someone can check if you have working with BMW autocom please have look between usb port and led`s what IC you got?

[alfy]

Maybe someone can check if you have working with BMW autocom please have look between usb port and led`s what IC you got?

That is a serial eeprom for FTDI 93c46, doesn't metter with communication with car!

[bestb]

OK but it can change voltage level somewhere ....
also I cant find the datasheet for atmlh124
I spot another difference
working one has IC 74HCT04D and AM29F800BB, XC68HC58EGA
not working IC is 74HCT14D and AM29F800BT, XC68HC58DW

[vergel]

Anybody can confirm if the autocom can connect to opel astra engine ecu?

I have autocom that never connect in astra ECU but can connect to other module
also it can connect to some BMW and other car

[makadam]

I have the same problem, tested on x12xel abd x17dtl. Other modules can be tested but engine????
Other cars are ok.

Sent from my Samsung Galaxy S2 using Tapatalk

[vergel]

is there anyway to fix this problem in opel car?

[cosmind]

Yes, missing one...

what is missing ?

thanks

[mishu_b]

I have the same problem, tested on x12xel abd x17dtl. Other modules can be tested but engine????
Other cars are ok.

Sent from my Samsung Galaxy S2 using Tapatalk


I can confirm that it is working on Opel cars. Very well I would say.

atb

[bibkare]

I tested mine so far on: Peugeot 407 MY2004 2.0 Petrol all modules OK, Renault Clio 2 1.5 DCI MY 2004 all modules OK, BMW E60 530 MY 2005 all modules OK also coding replaced battery, VW Crafter MY 2009 all modules OK, Fiat Punto MY 2002 all modules OK, Ford Mondeo MY 2004 all modules OK, Mercedes E210 MY 2002 all modules OK, in general all cars connect very fast, exception was renault - there was some delay

[vergel]

Mine also works on some fords car and bmw
The only problem I found as of now is not connected on Opel Astra engine ECU, how to fix this problem?

[makadam]

I can confirm that it is working on Opel cars. Very well I would say.

atb

Maybe some relay is broken. Did u test on Opel after 2004 or before, because protocol is not same!

Sent from my Samsung Galaxy S2 using Tapatalk

[athlonxp]

I need info pin to pin fiat 3pin to obdII autocom adapter because universal don't work. Thanks

[makadam]

Today I test Autocom on Xsara Picaso 2.0 HDi 2002 and it doesn't connect to engine. Other modules are OK

[zecas]

Today I test Autocom on Xsara Picaso 2.0 HDi 2002 and it doesn't connect to engine. Other modules are OK

strange i just diagnose an old xantia II from 98 without problems

[mishu_b]

Maybe some relay is broken. Did u test on Opel after 2004 or before, because protocol is not same!

Sent from my Samsung Galaxy S2 using Tapatalk


So, let me re-fraze the statement:

1. tested on Opel Astra G 17DT (2001) K_line (old protocol KWP2000) - 100% worked
2. tested on Opel Vectra C 19DTH (2008) CAN - the new protocol for communication - 100% worked.

I hope now I'm more clear then before.

atb

[makadam]

Maybe someone knows what reley is used for kwp2000 protocol?
Also My two autocoms doesn't connect to motor ecu on peugeot HDI 1.4 1.6 and 2.0 . Other modules work fine on astra and peugeot.

Sent from my Samsung Galaxy S2 using Tapatalk

[vergel]

Maybe someone knows what reley is used for kwp2000 protocol?



I think the problem is not about the Relay issue mate.
I replace all relay wit a 100% good relay but the problem is just the same

I try this autocom in Opel Astra 2003 with Z16XE engine and did not connected in Engine ECU but it can connect to ABS,
ABS and engine of this Astra-G used the same protocol (KW-2000) which is use pin7 of diagnostic socket

If this tool can connect to ABS, I think the KW2000 protocol is good. but why it cannot connect to engine ECU? I think it has another problem.( firmware or Hardware problem?)

[cosmind]

replaced max4820 and dont work on bmw 2006. generic obd works via kwp2000 (ISO-14230), others ecu works via kwp2000 but on bmw 2005-2007 dont work.
if I change relays PCB from faulty autocom with other from working autocom all are ok !!!

checked relays and all are ok, new max4820 .... what else I must check ?

[baner]

replaced max4820 and dont work on bmw 2006. generic obd works via kwp2000 (ISO-14230), others ecu works via kwp2000 but on bmw 2005-2007 dont work.
if I change relays PCB from faulty autocom with other from working autocom all are ok !!!

checked relays and all are ok, new max4820 .... what else I must check ?

Maybe other passive elements: resistors, capacitors, driver transistors, diodes,... There must be difference in those elements in working and nonworking PCB with relays!?:ahhhhh:

Regards and respect!:bounce:

[elchip]

Maybe other passive elements: resistors, capacitors, driver transistors, diodes,... There must be difference in those elements in working and nonworking PCB with relays!?:ahhhhh:

Regards and respect!:bounce:
Did any of you check wiring on PCB difference on that 2 type autocom cdp ... :captain:

[bestb]

Maybe other passive elements: resistors, capacitors, driver transistors, diodes,... There must be difference in those elements in working and nonworking PCB with relays!?:ahhhhh:

Regards and respect!:bounce:

a have a lot non working CDP - is not the relay pcb!
I swap the boards non working with working.. so It must be (in my case) differences at the main PCB...

[gelencserg]

I think the problem is not about the Relay issue mate.
I replace all relay wit a 100% good relay but the problem is just the same

I try this autocom in Opel Astra 2003 with Z16XE engine and did not connected in Engine ECU but it can connect to ABS,
ABS and engine of this Astra-G used the same protocol (KW-2000) which is use pin7 of diagnostic socket

If this tool can connect to ABS, I think the KW2000 protocol is good. but why it cannot connect to engine ECU? I think it has another problem.( firmware or Hardware problem?)

I also have AutocomCDP from China.
This is not working opel engine ECU.
10 to 15 attempts. I once worked but lost.
ABS, Airbag, working .....
Tested on:
Astra X17DTL
Astra 2005 Z16XEP
Astra C14NZ
And more opel
What is wrong??

[AEN]

Hello!

Can you guys share how Autocom Cars works with ECU of automatic gearboxes?

[Meat-Head]

Just like to add to this.

~Just come back from vacation~ From what i understand of Spanish, French and Emerican. Although this is soo obvious, to certain members it's unreal, but for those unaware of this fact.

Low battery voltage seems to damage the Bluetooth Module on these units.

The Tour Bus Guide was saying

[jezzus]

hello everybody,

i have autocom, but my vw golf 4 and other my cars, program say that: 'vehicle not supported this'..
what is the problem, not communicate or program dont working? please help.. / i dont make two resistor and two 9241a changed, but i order from this ic.../ But what is the problem?

[Marek_Spy]

I have one who not detected VCI anyone repaired this? As it looks for a moment something appears and passes on to another com. The control panel shall be submitted on the VCI com 7 . I think it's bad communication ATtiny 45 what do you think?
Marek

[Smac_a]

I have one who not detected VCI anyone repaired this? As it looks for a moment something appears and passes on to another com. The control panel shall be submitted on the VCI com 7 . I think it's bad communication ATtiny 45 what do you think?
Marek

If tiny45 is dead/not comunicating... your vci would show on hardware test. It would only say that serial is wrong (it detects one strange serial 10xxx).

Check coms, hardware...
Regards

[elchip]

If tiny45 is dead/not comunicating... your vci would show on hardware test. It would only say that serial is wrong (it detects one strange serial 10xxx).


Maybe it will detect 20000 serial if have problem with ID chip.

:listen:

[Smac_a]

Maybe it will detect 20000 serial if have problem with ID chip.

:listen:

That's the one... It is more 20xxx than 10xxxx :)

:five:

Regards

[Marek_Spy]

Tomorrow I will try to make a movie of what is happening. It is as if incorrectly answered

[angolcar]

Hello! Now I bought a Chinese version of an AutoCAD CDP. Can you help on how to upgrade? Now 2011/1 version. I read that you already have 2011/3 as well. Thank you!

[mbtuning]

you need the keygen but it is not available yet for public...

[didi_du_93000]

Hello, i have a question, if i try to connect my device on a other laptop. Is it working or no?
Thanks in advance

[bibkare]

should work on as many as you connect it

[autocargo]

I think that the latest version with file activation It won't work unless you deactivate it on the first computer you installed and then you transfer the activation on other computer...something like that.

[bardizoltan]

Hi all,

There is no OKI M6636B chip in many chinese clone autocom cable. It is needed for many FORD cars.

There are 2 types of IC on the market:
- Made in Japan
-Made in Thailand

We bought Japan version, but it doesn't work. Then everybody said that was the problem. We should have bought Thailand version.

Anyone has any idea ? ( Where to buy, or what is the problem with Japan IC ? )

[elchip]

Hi all,

There is no OKI M6636B chip in many chinese clone autocom cable. It is needed for many FORD cars.

There are 2 types of IC on the market:
- Made in Japan
-Made in Thailand

We bought Japan version, but it doesn't work. Then everybody said that was the problem. We should have bought Thailand version.

Anyone has any idea ? ( Where to buy, or what is the problem with Japan IC ? )

That two IC are not same .....

[vwpassat]

Are you sure is working with DAF and Scania?
Please, just let me know.

FYI, does NOT working with VOLVO heavy duty, any kind. Tried on few FH, FH16, Volvo bus chasis. Not conectinig message "Vehicle does not respond" is all you got.:stupid:

Also does not work with Renault trucks within Volvo group (DCI DXI). Not checked with Renault e-tech:afraid:.

Also does not work with chinese cables on IVECO. Even does not power up VCI interface.

MAN, Mercedes, DAF are (mostly) OK:top:.

So I would say, fifty-fifty. But for that price is not bad!

Regards and respect.;)

[baner]

Are you sure is working with DAF and Scania?
Please, just let me know.

Yup!, Worked on newer DAFs XF105, and older Scanina (I currently do not rememeber exact model, but it was with old round diagnostic connector).

Regards and respect!:ciao:

[sarkann]

Dear DK friends,

yesterday Autocom cdp was delivered to me. I wanted to install it, but after installation "configuration system failed to initialize" appears. I don?t know what to do. It?s clon, there is no readme file on CD. After installation of first software "CDP cars" icon appears on desktop. Than it starts to install next software package, but it asks ID, and if I input ID, it writes, that?s the ID is incorrect.
Please could somebode share working installation software with step-by-step guide?

[Marek_Spy]

install framework now . It's in DVD

[sarkann]

Of course framework is installed and reinstalled again, no change. :shot:

[crisx24ro]

I have version 2011.1 and a friend made the mistake in the firmware update. Now no longer going to configure interface (no longer detects interface, what can I do in this case?

[elchip]

I have version 2011.1 and a friend made the mistake in the firmware update. Now no longer going to configure interface (no longer detects interface, what can I do in this case?

Here is more then you was explain M8.
And your serial is not china serial ...
U do manipulating with HW too ..

[vwpassat]

Thank you.
I will try to call someone tomorrow and check it. I hope it's worth.

Yup!, Worked on newer DAFs XF105, and older Scanina (I currently do not rememeber exact model, but it was with old round diagnostic connector).

Regards and respect!:ciao:

[crisx24ro]

this is not my serial, have 32050 like all china clones autocom. This image i have from website. Let me know if is a change to put the right firmware who was on autocom. After update, i receive test fail. Tomorrow i will give picutre with my autocom and same error.

[elchip]

this is not my serial, have 32050 like all china clones autocom. This image i have from website. Let me know if is a change to put the right firmware who was on autocom. After update, i receive test fail. Tomorrow i will give picutre with my autocom and same error.


_______________________________________
crisx24ro (http://www.digital-kaos.co.uk/forums/members/24901-crisx24ro/)
Newbie

Join Date: Dec 2008
Posts: 19 (http://www.digital-kaos.co.uk/forums/search.php?do=finduser&u=24901)
Thanks: 0
Thanked 0 Times in 0 Posts
Downloads: 1
Uploads: 0


_______________________________________

Think about these ....
Maybe in future will be help to you ...
For now you need do more here...

Regard's

[crisx24ro]

i want only to know if is an solution to repair this unit

[Marek_Spy]

I understand you, I had a similar problem with one. Warmed by hot air soldering and worked. This may be in the FT and the ATtiny 45

[crisx24ro]

and now your work? can you give me a picture where to warm?

[michalez]

Here you go :sheep:

DUMP FROM ATTINY 45

FOR PASSWORD PM ME

[elchip]

Here you go :sheep:

DUMP FROM ATTINY 45

FOR PASSWORD PM ME

Who is here Sheep ?????????
Or you think you are genius ?

[michalez]

You are angry that you will not sell anymore dump for autocom or what ;)

[elchip]

You are angry that you will not sell anymore dump for autocom or what ;)

No but " Sheep" is not nice word.
And I no need any DUMP to do it.
I do it all via USB include FW.
Also all modification I was made to
enable all protocol work for all CAR and Truck...

From now to future my PM is disabled.
Do not ask me for solution anymore.

Good lucky

[STK340]

No but " Sheep" is not nice word.
And I no need any DUMP to do it.
I do it all via USB include FW.
Also all modification I was made to
enable all protocol work for all CAR and Truck...

From now to future my PM is disabled.
Do not ask me for solution anymore.

Good lucky
hi,
we are here to help each other,with certain conditions off course but not business,
so if you don't help here is no problem for us small ones is no loss,
even not have to bother to answer us,
regards

[elchip]

hi,
we are here to help each other,with certain conditions off course but not business,
so if you don't help here is no problem for us small ones is no loss,
even not have to bother to answer us,
regards

I will help only transparent from now in POST not on PM.
So I will read and post when I choice what and where.

That is that.

[XPS]

Deleted
Deleted

[elchip]

As the sensitive child from whom have taken away a candy.

Yes like SKARYMISTAKE was post his offline solution for some SW .... and now china resale his solution on every DVD for PSA ...

That is reason...

And look better your number of post's and solution here ....
And read better all ....

[Marek_Spy]

But what the quarrel? No better help a friend?

[elchip]

But what the quarrel? No better help a friend?

Yes it is better.

autocom cdp
Views: 47,714
Posted By Marek_Spy
But what the quarrel? No better help a friend?

But what the quarrel? No better help a friend?
Forum: Help and Discussion 27th April, 2012, 09:31 PM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
I understand you, I had a similar problem with...

I understand you, I had a similar problem with one. Warmed by hot air soldering and worked. This may be in the FT and the ATtiny 45
Forum: Help and Discussion 26th April, 2012, 09:47 AM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
install framework now . It's in DVD

install framework now . It's in DVD
Forum: IMMO 7th April, 2012, 05:29 PM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
I have no contact with EWS :(

I have no contact with EWS :(
Forum: IMMO 4th April, 2012, 09:01 PM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
no one can help me ? Here are the original data...

no one can help me ? Here are the original data from the controller
Forum: IMMO 4th April, 2012, 08:51 AM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
I read Xprog :bounce:

I read Xprog :bounce:
Forum: IMMO 4th April, 2012, 01:59 AM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
yes engine start if I will inject petrol on the...

yes engine start if I will inject petrol on the air , ca 1500- 4000 speed
I can not see MCU 1D47J , To look for in which place ?
what programmer unit will I read this ?
I try do it
Forum: IMMO 4th April, 2012, 01:11 AM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
now it is impossible because: the car was...

now it is impossible because:
the car was repaired after damage to the mechanical key , after car repairing not worked (mechanical repair ) . The next step was the replacement chip in EWS , car not...
Forum: IMMO 4th April, 2012, 12:24 AM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
not EWS2, I have schema and it is EWS1 , Memory...

not EWS2, I have schema and it is EWS1 , Memory ECU is 27C512 or 27C256 . I clean memory and write bin off immo but engine not work good .
Forum: IMMO 3rd April, 2012, 08:09 PM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
EWS 1 no emulator, I did once bin but engine not...

EWS 1 no emulator, I did once bin but engine not work good
Forum: IMMO 3rd April, 2012, 06:11 PM
Replies: 14
BMW 316 year 1995 immobiliser
Views: 175
Posted By Marek_Spy
BMW 316 year 1995 immobiliser

Hello
I have a big problem with this car is damaged immobilizer and I can not run. Can anybody generate bin immo off? . Memory there is a 27C512. ECU Bosch 0 261 203 660
Forum: Help and Discussion 2nd April, 2012, 03:32 PM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
Tomorrow I will try to make a movie of what is...

Tomorrow I will try to make a movie of what is happening. It is as if incorrectly answered
Forum: Guides, Tutorials and Discussion 22nd March, 2012, 08:52 PM
Replies: 520
Experience with Autocom
Views: 43,669
Posted By Marek_Spy
Hello I have a problem with my china clone. The...

Hello
I have a problem with my china clone. The program does not recognize the VCI. I have good drivers and control panel on the VCI com 7 What might be the cause and where to look
Marek
Forum: Help and Discussion 22nd March, 2012, 07:46 PM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
I have one who not detected VCI anyone repaired...

I have one who not detected VCI anyone repaired this? As it looks for a moment something appears and passes on to another com. The control panel shall be submitted on the VCI com 7 . I think it's...
Forum: Help and Discussion 12th March, 2012, 06:36 AM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
I can not help you I have not BMW

I can not help you I have not BMW
Forum: Help and Discussion 12th March, 2012, 12:07 AM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
See exactly what are the differences between the...

See exactly what are the differences between the PCB may be the solution to the problem of communication with BMW
Forum: Help and Discussion 9th March, 2012, 07:38 PM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
I think that it would be good to do list of bugs...

I think that it would be good to do list of bugs and gather it together . What do you think?
Forum: Help and Discussion 9th March, 2012, 12:04 PM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
I find in china . But schipping is expensive

I find in china . But schipping is expensive
Forum: Help and Discussion 9th March, 2012, 10:09 AM
Replies: 665
autocom cdp
Views: 47,714
Posted By Marek_Spy
were I buy M6636B ? have good seller ?

were I buy M6636B ? have good seller ?
Forum: Diagnostic/Workshop 9th March, 2012, 09:01 AM
Replies: 4
Autocom CDP Pro Cars software download
Views: 638
Posted By Marek_Spy
not ckraked :(

not ckraked :(
Forum: Introduce Yourself 12th December, 2011, 04:47 PM
Replies: 2
Hello
Views: 67
Posted By Marek_Spy
Hello

I greet all on the forum and I hope that my writing someone will be useful about how much them he will write.
Forum: General Automotive Help and Discussions 12th December, 2011, 11:34 AM
Replies: 120
Repair Op-com Hardware Procedure?
Views: 17,401
Posted By Marek_Spy
Hello I already got lost . How do enough was he...

Hello
I already got lost . How do enough was he working from the programme from Adako the version 110207c ? Will someone prompt me maybe ? I tried this bootloaderem but he does not work , the...
Forum: General Automotive Help and Discussions 4th June, 2011, 07:33 PM
Replies: 112
PPS2000 and Lexia repair
Views: 14,610
Posted By Marek_Spy
I have a problem with my china clone. Connects to...

I have a problem with my china clone. Connects to the C5 2001 and 2003, will not connect to the C3 in 2005,manually by entering the VIN C3 combines with ABS and engine but did not recognize the...
Forum: Radio Decode 6th March, 2010, 11:04 AM
Replies: 6
VW POLO Blaupunkt Radio Code help please
Views: 482
Posted By Marek_Spy
U must read memory

U must read memory


As I see you helped a lot to all ...

Regard's

[Marek_Spy]

I see that you worked hard searching for all my posts. Even I did not know that so many have written. Greetings to you

[elchip]

I see that you worked hard searching for all my posts. Even I did not know that so many have written. Greetings to you

One click solution :-)

[michalez]

so you have solution to avoid chinese sellers? only closed small forum can avoid this.


and btw i like this picture :sheep::sheep::sheep::sheep::sheep: :)

[Marek_Spy]

This palce I sold with hot air. I'm sorry that so long but I had to find a photo. I hope this will help you

[rapkopat]

hi frend pass plaese

[DiagService]

HI guys i have problem with bluetooth when I connect I put zero as password is not good have any problem with bluetooth ??????

[smokey08]

HI guys i have problem with bluetooth when I connect I put zero as password is not good have any problem with bluetooth ??????

use 0000 as password

[chrismoore02]

Try 1234 as password for bluetooth as i have a unit that does not accept 0000 but 1234 worked ok - hope this helps someone

[Marek_Spy]

the BT module can be freely programmed. I can give instructions .

[digimile]

hi
is autocom cdp also used for programming modules if ecm is replaced by new one...my question is if car has damaged ecm and need replace then this tool can programm ecm also..and other modules of the car...
thanks

[Marek_Spy]

unfortunately, a very simple diagnostic device

[DiagService]

use 0000 as password

thanks it s 0000
thank sss alllll

[crisx24ro]

anyone can help me to make downgrade from 2011.3 to 2011.1? need photos with pin where to conect programer.

[autocargo]

To downgrade firmware you don't need programer. It's all made thru USB port. There are posts on this forum about this procedure. But tell me, why downgrading from newer version to older one?

[crisx24ro]

give me please a link or tell me to downgrade. I want downgrade becuase a friend maked a mistake and push button update. Now my software don't see firmware and i can't make diagnostics.

[alfy]

give me please a link or tell me to downgrade. I want downgrade becuase a friend maked a mistake and push button update. Now my software don't see firmware and i can't make diagnostics.

Just connect to old SW and do UPDATE again!
Interface must be connected to car or 12V on OBD!

[crisx24ro]

thanks a lot, working now.

[Chokito5]

I have a firmware problem too. My tool was good, but I lent it to my friend, and since then it has firmware error. I attached picture from it.

I tried to re-install the software, and Update, but that is not work for me. I attached that picture too.

Can I repair it? It is clone.
Thanks

[smokey08]

I have a firmware problem too. My tool was good, but I lent it to my friend, and since then it has firmware error. I attached picture from it.

I tried to re-install the software, and Update, but that is not work for me. I attached that picture too.

Can I repair it? It is clone.
Thanks

Plug your interface into a car then try updating firmware.

[vwpassat]

Anybody can help me with wiring adapter MAN trucks, from OBD2 to 37pins plug diagnostic.

[Chokito5]

I plugged the Autocom to the car, and I plugged to my computer too. But i have got the attached pictures.

[Chokito5]

What would you like? Buy or made? I will get today one set of Autocom Truck cable. This contains the MAN 37 pin adapter cable too.

[Smac_a]

Yes. But did you press the update button (as smokey08 suggested)?

Smac_a

I plugged the Autocom to the car, and I plugged to my computer too. But i have got the attached pictures.

[XPS]

I plugged the Autocom to the car, and I plugged to my computer too. But i have got the attached pictures.
To you will help only programming device.

[Chokito5]

Dear Smac_a:
Yes, I press the Update button too.

Dear XPS:
Which programming device? I have Upa, which chip do I need to program? Have you got the good program?

[XPS]

Dear XPS:
Which programming device? I have Upa, which chip do I need to program? Have you got the good program?

AM29F800

Upa will not help.

[Chokito5]

Which tool do I need to program this chip? If I buy it, have you got the program too?

[Smac_a]

Willem shoud do it, but you need an adapter for tsop 48.
Flash content is posted somewhere on DK.
But how did this happen in the first place? Check soldering
around the flash...

Regards,
Smac_a

Which tool do I need to program this chip? If I buy it, have you got the program too?

[Chokito5]

Ok, thanks your help. I will check the soldering.

Best regards

[ZIZZOU]

Here you go :sheep:

DUMP FROM ATTINY 45

FOR PASSWORD PM ME
hi my freind
would you send me pw for attiny dump?
thank you

[Chokito5]

Willem shoud do it, but you need an adapter for tsop 48.
Flash content is posted somewhere on DK.
But how did this happen in the first place? Check soldering
around the flash...

Regards,
Smac_a
I checked the soldering, I didn't find any trouble. Now I will try to reprogram the chip, but I need to buy one Willem programmer. Where should I buy Willem? Have you any idea?

Thanks

[Chokito5]

I have bought Autocom Truck cable set. But the Iveco 30 pin cable is not working. When I plug the Autocom tool to the adapter cable, and that plug to the truck, the tool is not get Voltage.

I measured the adapter cable:

OBD2 plug - Iveco 30 pin plug
16 - 30 pin (24V)
4 - 29 (GND)

I measured the plug of the Iveco truck too. The 30 pin is the GND, the 27 pin is the 24V.
When I changed the pins on the truck (27 pin to 30 pin, 30 pin to 29 pin), the Autocom work well.

The cable is not good for this Iveco. Have you got similar problem? I think, not a good idea to change the pins the all IVECO :)
Have you got different Iveco 30 pin cable?
I tried to search other Iveco 30 pin cable, but where they show the schematic of the cable, that was same as mine.

I don't understand it.

[Tachotony]

Hi

have somebody succes to connect an Volvo or

Renault DXI truck with Autocom ??

i test 4 but no succes

Regards tonny

[digimile]

hi
someone can share vehicle list of autocom cdp car list ...thanks

[paro44]

hi
someone can share vehicle list of autocom cdp car list ...thanks

Here it is for 2011.1: http://www.autodiag.de/upload/service/application-cars-cdp-pro.pdf

[XPS]

In mine Autocom there is no communications on CAN.
Problem in a board with relays.

Whether there is a diagram of conductors Autocom?

[mbaja]

Just my experience with autocom updating firmaware... - Maybe it will help someone - I Couldn't update it (also incorrect firmware message appeared) while it was plugged to external AC/DC 12 charger....then went to my car and updated it successfully - obviously the voltage stability is very important...And i have seen everyone telling "plug to a car" and update firmware(but thought it is just the same as "power the interface with 12V DC supply")....obviously it is important that it is NOT plugged to AC/DC 12V adapter or "CHEAP AC/DC 12V adapter"...

[dieseldocter]

hi guys
i have autocom cdpro for trucks works ok with renault dxi and dci trucks

[ramsi17]

Hello Everyone i have a problem, with installing autocom cdp, i need id for installl, mi version is 2011.1, and i dont know if a need another file for operation.

thanks for your cooperation

grettings

[WhoAmI]

Hello Everyone i have a problem, with installing autocom cdp, i need id for installl, mi version is 2011.1, and i dont know if a need another file for operation.

thanks for your cooperation

grettings

ID fir PC: a-710-479

[odednovo]

I tried to replace one of the 9241a chip and the pad of number 5 chip leg was torn from the board (as circled in the photo).
now I want to solder new chip and I want to arrange junmper from this chip leg to where the pad is connected the board but I can find where can I connect the jumper.
Can anyone help me to check in a good board where the pad connected in the board?

[morfej]

On picture you marked pin 8.... as pins on chip are not counted as you think :)

[meteor80]

Hello.

I have problem with my Autocom.
After activation 2011.3 and firmware upgrade I have error "VCI not found"
SOftware recognize interface but when I tries to test some module there is connection and at once "VCI not found"

When I downgrade to version 2011.1 the VCI works fine.

Someone know something about that error?

[Ashraf6119]

Hello.

I have problem with my Autocom.
After activation 2011.3 and firmware upgrade I have error "VCI not found"
SOftware recognize interface but when I tries to test some module there is connection and at once "VCI not found"

When I downgrade to version 2011.1 the VCI works fine.

Someone know something about that error?


Hi

If your Activation File had some errors (Not Activated Properly) That's what it will do...........

The Software Program will open but, VCI Not Found errors you will keep getting..........

So try Activating it again and see if that helps.............

[Smac_a]

It is usualy the serial number problem (30250) rather then activation problem. Serial is blocked in software in some cases...

Regards,
Smac_a


Hi

If your Activation File had some errors (Not Activated Properly) That's what it will do...........

The Software Program will open but, VCI Not Found errors you will keep getting..........

So try Activating it again and see if that helps.............

[odednovo]

yes my mistake

it is pin8
do you know where it connected in the board?

[Chokito5]

Just my experience with autocom updating firmaware... - Maybe it will help someone - I Couldn't update it (also incorrect firmware message appeared) while it was plugged to external AC/DC 12 charger....then went to my car and updated it successfully - obviously the voltage stability is very important...And i have seen everyone telling "plug to a car" and update firmware(but thought it is just the same as "power the interface with 12V DC supply")....obviously it is important that it is NOT plugged to AC/DC 12V adapter or "CHEAP AC/DC 12V adapter"...
It helped for me :)
I tried with my car, not with 12V DC supply, and it is worked. My Autocom is good again!

Thanks!

[odednovo]

On picture you marked pin 8.... as pins on chip are not counted as you think :)
my mistake

it is pin 8
Do you know where it suppose the be connected

[meteor80]

So maybe someone will activate it for me?

[WhoAmI]

Hello.

I have problem with my Autocom.
After activation 2011.3 and firmware upgrade I have error "VCI not found"
SOftware recognize interface but when I tries to test some module there is connection and at once "VCI not found"

When I downgrade to version 2011.1 the VCI works fine.

Someone know something about that error?

Hello!
I have 2 Autcoms and same problem like you. They both have serial 30250. I made fresh install (Windows and Autocom) and i hope it will work. Now i asking if someone can activate it. Thanks.

[obdmaster]

So maybe someone will activate it for me?

pass in pm:top:

[damiantucha]

So maybe someone will activate it for me?

123382

thanks

[sumi1]

Good evening, AUTOCOM works with Windows 7 release 03-2011?Thank you

[ramirez2]

Good evening, AUTOCOM works with Windows 7 release 03-2011?Thank you
yes...work

[mechanior]

stopped working my orginal cdp pro and do not know if this is a problem with software or hardware, starred in batches if anyone would be able to look at them and say what went wrong and where is s / n at which the address is for my: BE302345 and should be out there somewhere be124913

[DiagService]

HI guys I have problem with MB C-Class W202 1996 year 2.0 benzina I can not connect with AutoCom ECU, Airbag, SRS, ABS...
Have you any Idea fot this solution ???

[baner]

stopped working my orginal cdp pro and do not know if this is a problem with software or hardware, starred in batches if anyone would be able to look at them and say what went wrong and where is s / n at which the address is for my: BE302345 and should be out there somewhere be124913

Seems that your FTDI chip is ~~~~ed and it need reprogramming.

Probably, one of your cables (VCDS or KKL VAGCOM) programmed wrong data into your FTDI chip.:alberteinstein:

So as result your computer does not see your CDP when you connect it with USB. Did you try to connect it with bluetooth?:hello:

Regards and respect!:jiggin:

[Chokito5]

Can anybody help me with this file? What do I have to do with this file?

Thanks

[sierra]

Can anybody help me with this file? What do I have to do with this file?

Thanks

Enjoy.
Description of how to activate the program look at this forum.

[djcristi]

activations moving to this (http://www.digital-kaos.co.uk/forums/f166/autcom-2011-3-free-activations-only-supporters-274488) thread

[sierra]

Hey. Has anyone watched the menu Developmen? Is there anything interesting?

http://img217.imageshack.us/img217/2089/20120604195828.png

[albematty]

hello
You can activate the license of autocom?
thanks

[mechanior]

I tried to call him by bloetooth and nothing connects the computer sees it Autocom well as trying to connect but only LED flash three times and hangs up before I had a problem with the update I had ten times the push update finally caught on and I think something is broken mechanically or ATTINY dead now try to upload the Chinese input and would like someone had it I would be very grateful thanks for your interest in the banner and greet

[fluorescent]

I tried to call him by bloetooth and nothing connects the computer sees it Autocom well as trying to connect but only LED flash three times and hangs up before I had a problem with the update I had ten times the push update finally caught on and I think something is broken mechanically or ATTINY dead now try to upload the Chinese input and would like someone had it I would be very grateful thanks for your interest in the banner and greet

You have to open the box and look for the cold joints on the circuits.Got a good flux and remake all the solders on the pcb.

[djcristi]

hello
You can activate the license of autocom?
thanks

here you go sir, activation only there. don't post anymore on wrong threads

[mechanior]

everything and checked the connections and tested the components and to me there is no damage, but double check it and here are pictures of my interface http://www.digital-kaos.co.uk/forums/attachments/f155/103705d1329422835-interface-picture-collection-cdp-pro.rar now wanted to test the Chinese soft on my interface, as someone has to ask for access to the test

[darrenhyland]

Check out this link 2012 the newest Autocom CDP+ have the function of TF card and the function of a key to start-in Auto Key Programmers from Automobiles & Motorcycles on Aliexpress.com (http://www.aliexpress.com/product-fm/573928441-2012-the-newest-Autocom-CDP-have-the-function-of-TF-card-and-the-function-of-a-wholesalers.html)

anyone got this yet???

[smokey08]

Check out this link 2012 the newest Autocom CDP+ have the function of TF card and the function of a key to start-in Auto Key Programmers from Automobiles & Motorcycles on Aliexpress.com (http://www.aliexpress.com/product-fm/573928441-2012-the-newest-Autocom-CDP-have-the-function-of-TF-card-and-the-function-of-a-wholesalers.html)

anyone got this yet???

I may try changing my serial number when I have time to 100251 with realterm and see what happens.

[furburger]

Check out this link 2012 the newest Autocom CDP+ have the function of TF card and the function of a key to start-in Auto Key Programmers from Automobiles & Motorcycles on Aliexpress.com (http://www.aliexpress.com/product-fm/573928441-2012-the-newest-Autocom-CDP-have-the-function-of-TF-card-and-the-function-of-a-wholesalers.html)

anyone got this yet???

If you hover over DVD pic in link it shows version as 2011.3 ;)

[djcristi]

doesn;t matter, still 2011.3 is the latest. but cdp+ has logging functionality

[furburger]

doesn;t matter, still 2011.3 is the latest. but cdp+ has logging functionality

Cool ;) does 20111.3 have more BMW models ~? my 2011.1 ends at DDE5.0 (on E46) nothing listed for later EDC16 models??

[djcristi]

yes, it has newer bmw f10/f01

[furburger]

that's good news:)
does it work well and are any live data readings available? (on a 2005 edc16. e46 320d for example)

[djcristi]

haven't tested it yet

[dsl400]

hello :D
now ... this looks intresting .... how did you do that ?

[djcristi]

dsl400 (http://www.digital-kaos.co.uk/forums/members/226379-dsl400/), did what?

[chrismoore02]

the hardware looks alot different, would be good to get some feedback on the CDP+ unit ie does the data logging work? and what software comes with it? is it 2011.3 or are they just saying that. Does it work with trucks? how is it activated etc etc i may have to buy one for a play

[djcristi]

i saw on description that it doesn't need activation?!? and it's dongle protected...

[chrismoore02]

so is the clone dongle protected have they cloned the dongle or using software crack? i cant see any hint of a dongle on the clone advert

[djcristi]

#1,Autocom CDP+ don`t need the activation code #5,Autocom have the function of TF card and the function of a key to start


that's why i think it's about a dongle...

[chrismoore02]

Yeah you might be right there. You have to love Chinese translation :rolleyes:

Sent from my Galaxy Nexus using Tapatalk 2

[djcristi]

it's curious that there are 2 pictures there is different clones i think, one like somehow like the original cdp+

[dsl400]

dsl400 (http://www.digital-kaos.co.uk/forums/members/226379-dsl400/), did what?

nothing ....
just a typo ... sorry

[furburger]

if software is same how can it have datalogging as a new or extra feature?? is it a case of 2011.3 with our regular interface has datalogging function but it's greyed out / not working or something?? with my tests I only find vag group has some datalogging capability ( 2011.1)