160D0WQ

[markony79]

I need some of this,
where is posible to buy?
or can change with 35080?

but I need 100% knowledge or with experience

Thanks

[carbandit]

smelecom uk sell them i believe

[marcio1758]

smelecom uk sell them i believe

with the 35080 will not work, your database is half the 160dowq, it is double in size, it is necessary to replace the same or 35,160, or delete your! R270 is able to do this!

[tachonow]

Also Codiprog has on its menu erase option for this chip.

[markony79]

Also Codiprog has on its menu erase option for this chip.

I have Codyprog, but I am afraid when do this,
becouse on D80D0WQ sometimes can not errased good, and must change with another

becouse off that I need one of this to have in my reserv..

[smartymarti]

160D0WQ is same as 35080 just read and put onto a new chip should be no issues

[ION CRISTI]

i replace m35080vp and work succesuful. in dash corsa d it is

[milesbetteroff]

Hi guys well a lot of info here some good here is my input I have r270 and have done these cars 160's take up to am hour to erase but I have used 35080 as replacement it did work as there is no info in second half of eeprom have only done it once just so I had a spare chip that I could have ready for next job so not waiting about for chip to erase hope this helps cheers

[markony79]

i replace m35080vp and work succesuful. in dash corsa d it is

I was do 2-3 Corsa D and never found this 160D0WQ
in Corsa is D80D0WQ

[smartymarti]

I was do 2-3 Corsa D and never found this 160D0WQ
in Corsa is D80D0WQ

3 then 6 then vp etc
there just the next geberation chips ie

[breno.monteiro]

see in carprog.lt , the new interface superprog work 160d0wq

[billykillkelly]

replace whit 38080 .... no worry

[T72]

replace whit 38080 .... no worry
have you ever saw dump from 160D0WQ?

[markony79]

I found this for 60e +post 30e from Italy
Its very good site,have hardware for dashes

Minitools Product - ERASER FOR 35080/M35080/35160/M35160 EEPROM (http://www.minitools.it/35080-m35080-35160-eeprom-eraser)

[smartymarti]

up voltage to 5v will over write v3 and v6 35080

[markony79]

up voltage to 5v will over write v3 and v6 35080

we talking about 160D0WQ, not 35080

[puiu]

I found this for 60e +post 30e from Italy
Its very good site,have hardware for dashes

Minitools Product - ERASER FOR 35080/M35080/35160/M35160 EEPROM (http://www.minitools.it/35080-m35080-35160-eeprom-eraser)

Where have you find the price for this tool,
i download the catalog ,but i can't find it ...
thank you,
best regards

Puiu

[vageric]

I found this for 60e +post 30e from Italy
Its very good site,have hardware for dashes

Minitools Product - ERASER FOR 35080/M35080/35160/M35160 EEPROM (http://www.minitools.it/35080-m35080-35160-eeprom-eraser)

i also found this side a couple of days bevore and send them a email
asking for price and they return email with price of ? 280,-.

[markony79]

Where have you find the price for this tool,
i download the catalog ,but i can't find it ...
thank you,
best regards

Puiu

I was found here
or I miss?

[puiu]

I was found here
or I miss?

This one can not erase eeprom...
60 euro was to god to be true,
but in picture is another programmer
and the price is 280 euro as vageric says..

Puiu

[smartymarti]

For that price of 280 euro your better off skipping all the cheap clone rubbish and getting a codiprog as there still on off at reduced price

[T72]

For that price of 280 euro your better off skipping all the cheap clone rubbish and getting a codiprog as there still on off at reduced price
Codyprog is damaging 80D0WQ when erasing! Some addreses in 0x00 and 0x10 becomes not write able, and stay 00 after programing! I do not know what dash software will "say" about some 00 in milage location. When I will have more time I will "play" more and will report here...
But looks like there is probleme with 80 and 160 D0WQ...

[vageric]

For that price of 280 euro your better off skipping all the cheap clone rubbish and getting a codiprog as there still on off at reduced price

how much is reduce price????
i see them for ?300,-

[tehnosoftex]

Codyprog is damaging 80D0WQ when erasing! Some addreses in 0x00 and 0x10 becomes not write able, and stay 00 after programing! I do not know what dash software will "say" about some 00 in milage location. When I will have more time I will "play" more and will report here...
But looks like there is probleme with 80 and 160 D0WQ...
I've played with codiprog damaged d080d0wq. If first 2 locations it is damaged then the dash will no work. I did today an opel astra and when i install a d080wq with first locations 0 , the dash display dashes instead of km.

[izi]

Hi

for info it's a manuel for the eraser minitool
I have buy this eraser (280? without VAT)


izi

[vageric]

Hi

for info it's a manuel for the eraser minitool
I have buy this eraser (280? without VAT)


izi

does the eraser work good??
any problem with erasing???

[smartymarti]

Iv not yet had a issue erasing any chips with the codiprog there is 1 in 20 Might not erase correctly iv not yet had it

[Speedosoft]

It seems the damaged bytes after erasing is not proper to the codiprog. ETL's 08ODO eraser too does the same thing. Some bytes remain on 00 and can no longer be overwritten by a higher value. I'm not really sure that this eraser from Minitools is better than codiprog or ETL.

[tehnosoftex]

Iv not yet had a issue erasing any chips with the codiprog there is 1 in 20 Might not erase correctly iv not yet had it
You are lucky Marty, I have 50/50 success rate with d080dq memories on codiprog

[smartymarti]

IV ONLY USED 4-5 UPTO NOW BUT WILL REPORT ANY ISSUES THIS WEEK WHEN IN USE

[breno.monteiro]

hello everybody, could someone give me an eraser 160d0wq that works well? erasing all eeprons? best regards breno

[her2011]

I found this for 60e +post 30e from Italy
Its very good site,have hardware for dashes

Minitools Product - ERASER FOR 35080/M35080/35160/M35160 EEPROM (http://www.minitools.it/35080-m35080-35160-eeprom-eraser)
yet this product is not available??
says something.
thanks

[breno.monteiro]

I sent e mail to them and said the price the article costs 280,00 Euro + delivery

someone already tested the equipment? tks

[smartymarti]

CodiProg USB - ElproSys (http://elprosys.com/index.php?option=com_content&task=view&id=51&Itemid=78)

[markony79]

Hi guys

I have from yesterday new Bmw F 5 serie
i can not erased the eeprom with Codyprog

where can I buy for next time this eeprom

[r-parts]

i haven't got any problem with codiprog and 35160, i updated it to last version, remove jumper 1 and 2 and it should work.

[smartymarti]

lat few chips ive done with codiprog it erases the first 6 bytes then leaves 4 then erases 6 ill ipload a picture as no one knows the issue

[r-parts]

Thats odd, i have seen waht you are experiencing on some old 35080v6's and vp's but not with d80 or d160, those work perfect with erasing function

[TULGEYWOODMAN]

just accept the fact that some chips wont erase

[smartymarti]

eric everyone that iv done done erased ok but not writing back ok as oicture i sent ya mate

[TULGEYWOODMAN]

When using codiprog on the laptop instead of standalone, I get better results

[breno.monteiro]

erase about 3 times , ok?

[dave11674]

can any1 confim which is best to use then ?
and what success rate they are getting upon erase !

thanks

dave

[rrador]

has anyone tried the minitools eraser?
or should i just get codiprog and accept the fact it wont always work

[camarock]

I have codiprog, and works well, also I have r270, and also works well, but few times I cant erase some chips, few time ago I know a seller to sell me some 35080s in 2 dollars, and works well, I proved in bmw 2011 and works well, also in opels and land rovers, without problems. cause one time I bought with china dealer and it was a desaster, I cant get back my money and enyone works

[diagtech]

With codiprog just read eeprom and save then write 00s into top 2 lines where mileage is stored then do miles with programmer never had a 35160 fail this way

[hass42]

Can I read 160D0WQ with UPA? or should use Xprog?

Also I have new M35080 chip Smarti say I can write 160D0WQ into this, anyone try?

[vrsc]

I do not think so 35080 have 1/2 Data

[PremierD]

Yes you can mate ........................ :)

[hass42]

But necessary to read as 160DOWQ of course, this is the mistake I made.

Thanks

Hass42

[hass42]

Any idea on how to read with upa? And I try with xprog and wont work either, I can read upa as m35080 but not all of chip reads

[hass42]

Yes you can mate ........................ :)

Ok, I try to write original file off of D160 chip into M35080 and it give me error at address 400 and it pretty much just doubled the file, SO 00 to 3FF is same as 400 to 7FF

Using xprog, anyone can help in sorting this out for me?

Hass42

[Faraday]

I use Martech BOX III. Read/erase- no problem. With xprog I had no luck to erase.

[smartymarti]

Iam seeing more and more bmw 7 series that have 35080 inside rather than the correct d160 obviously complete amateurs that cant erase them , so they are working ok all the functions are there and i cant see any difference and there no dtcs relating either

[hass42]

I have a mismatch dot and every time ignition switch on and off it adds 3 miles

When I read file from D160 it reads correct, but when I use new D080 chip to write, xprog give write error at address 400 and I continue write.
After finished, address 00 TO 3FF is as address 400 to 7FF

Hass42

[smartymarti]

I have a mismatch dot and every time ignition switch on and off it adds 3 miles

When I read file from D160 it reads correct, but when I use new D080 chip to write, xprog give write error at address 400 and I continue write.
After finished, address 00 TO 3FF is as address 400 to 7FF

Hass42

why not erase the chip or send it to someone who can for you

or even better buy an eraser

[hass42]

Already ordered, just need this vehicle to be done like yesterday lol . I have 35080 eraser just I never fun into this chip, even though I have done a F BMW with a cas4 before several times.... Just never run into this chip

Hass42

[hass42]

Does anyone here know if 2012 X6 has a 160D0WQ?

[kautuvera]

Does anyone here know if 2012 X6 has a 160D0WQ?

X6 E71 0D80WQ

[elephantul]

Iam seeing more and more bmw 7 series that have 35080 inside rather than the correct d160 obviously complete amateurs that cant erase them , so they are working ok all the functions are there and i cant see any difference and there no dtcs relating either

http://www.digital-kaos.co.uk/forums/showthread.php/344099-Bmw-cas4-160D0WQ?highlight=160d0wq

[hass42]

Yes you can mate ........................ :)

Ok, I must be doing something wrong here, I try to write (new chip, have used these plenty with no problems quality chip) 080w0dq with file below with xprog as m35160 and it will double file info after line 400.

so 0 - 400 same as 400-800. It will reread chip but info is doubled, and during write it gives me error at 400

I was getting red dot on dash, does anyone know if I have to do something in settings of xprog or anything?

[vageric]

QD080 is almost same as M35080
QD160 is almost same as M35160
so if you write 080 into 160 then it doubled yes

[hass42]

I am writing 160 into 080 and first half of 160 is doubled onto 080

seems confusing, but im sure someone gets what Im talking about here

[vageric]

you cant write 160 into 080
because 160 is bigger than 080
160 is twice the amount of data that go's into 080

[hass42]

That makes all the sense to me, but I have read time and time again on here that I can write with no problem. So it makes me wonder if there is a way to do so?

[vageric]

i think you have read that some write QD080 into M35080
or even M35080 into QD160
but 160 into 080 just not possible. otherwise you will loose data
or the data used in 160 is same amount as in 080 and the rest (second half) are all 00 an FF

[hass42]

I see, so I need to use the 160 because my 160 file has plenty on second half of chip. Ok

[hass42]

Anyone have a clue where I can buy this D160 chip at?

[teerak2uk]

I use codiprog to do these in circuit

[Landetos]

I use codiprog to do these in circuit

Good advice!

Never change 35160 or 160d0wq to 35080...

If change is needed change it to same one...

35080 is 2 times smaller than 35160...

You will loose data in BMWs after 2010-

These have data stored after 35080 capacity!

With best regards to all,

Landetos

[Landetos]

Anyone have a clue where I can buy this D160 chip at?

160D0WQ + 080D0WQ - both types tested, virginized and working 100%

Here:

http://vendocuadros.com/dashboards-parts/eeprom-chips

Best regards,

Landetos

[teerak2uk]

160D0WQ + 080D0WQ - both types tested, virginized and working 100%

Here:

http://vendocuadros.com/dashboards-parts/eeprom-chips

Best regards,

Landetos
Expensive and no advertising allowed

[peko]

hi friends

why you mod this cars ? when guy go to office, seller trace ori via connecteddrive ....

[javyb]

hi friends

why you mod this cars ? when guy go to office, seller trace ori via connecteddrive ....
Done a fair few, never had any issues

Sent from my SM-G935F using Tapatalk

[mouss]

i see 280? and pay 30? for shipping look at catalogue minitool.it

[mouss]

I found this for 60e +post 30e from Italy
Its very good site,have hardware for dashes

Minitools Product - ERASER FOR 35080/M35080/35160/M35160 EEPROM (http://www.minitools.it/35080-m35080-35160-eeprom-eraser)

i see 280 euro in catalogue my friend

[Meat-Head]

no advertising allowed

Only blatent advertising is banned like this

ADVERTISEMENT:-

www.meat-head-motors.co.uk free scratch with every scuff

BUT this is helping others not ‘advert’

ON TOPIC:-

ADVERTISEMENT:-

http://www.cartool.co.uk/wholesale/160d0wq-eeprom-chip.html

[gjenkins0]

digimaster 3 is a very good tool for this chip