New Fiesta 2011

[marcio1758]

please please someone help me with the connection panel 9s12hz128 fiesta 2011, thank you all in advance

[carbandit]

here you go friend

[marcio1758]

Thank you my brother of DK, but not this image! I have this, this is a 9s12HZ256, I need 9S12 HZ128 as above!

[mastaflex]

BDM points are in your picture number 2. and use this picture and a multimeter to check what are corresponding pins to BDM points

[rgomesbrito]

In upa You can not do the reading because this processor has bits securyti, refer you to use a XPROG 5.0

[rgomesbrito]

http://images.orkut.com/orkut/photos/OgAAAEfByIAgOKj6nXvuVqnzbEtZR6SxXpwIgBjWrABQdIFuds NYR9QwoYGkgMPEz4coRhfITrXPKN_HWMC_d19kppMAm1T1UOwY 1uYQJpNsLoXEL_hX2jLPfK5q.jpg


this is the photo to make through the XPROG

[Apolo29]

Could you do it? which cristal does it have?

I`m very interested in this dash.

[vuno01]

what programmer do you use?

[digimile]

hi
error in opening image please upload here.
thankx

[martin292009]

Bro look this...
MC9S12HZ256 datasheet(32/692 Pages) FREESCALE | HCS12 Microcontrollers (http://html.alldatasheetcn.com/html-pdf/161824/FREESCALE/MC9S12HZ256/15866/32/MC9S12HZ256.html)

[martin292009]

MC9S12HZ128VAL IC MCU 16BIT 2K FLASH 112-LQFP Freescale Semiconductor datasheet pdf data sheet FREE from datasheetz.com (http://datasheetz.com/data/Integrated%20Circuits%20%28ICs%29/Microcontrollers/MC9S12HZ128VAL-datasheetz.html)

[astrocar]

upa usb not read

[smokey08]

I got one of these in tommorow. Does anyone know if the mcu is secured?

[drpeter]

I got one of these in tommorow. Does anyone know if the mcu is secured?


I did one 5 minutes ago by OBD is not secured you can also read the chip with UPA see picture above (edited by me!!!).

[smokey08]

Thank you drpeter. I will try with xprog-m.

[billykillkelly]

do not try whit xprog ( use upa if you dont have ford km tools....

[n599fbm]

try this,

rgds,

C.

[smokey08]

Did this today with xprog-m and drpeters diagram. Worked perfectly, Xprog automatically detected that it had a 9s12hz128.

Thank you all.

[chrismoore02]

could someone please post the connections for this dash for x-prog m?

is the dash secured? if so i take it i cant use my upa

many thanks

chris

[PremierD]

you can use UPA mate ..HZ processor .. I think ..lol

http://www.digital-kaos.co.uk/forums/f174/new-fiesta-2011-a-194769/

[chrismoore02]

Many thanks, looks like you dont even need to remove the needles too. :D

Thankyou

[chrismoore02]

could someone check this dump for me please, the original mileage was 32924miles i have edited this dump to 8000miles but when written back and put in the car it does not like it :(

[PremierD]

You have original mate .. ?

[chrismoore02]

Yes I'll post them now. I would like to know where I went wrong. Thank you

[chrismoore02]

here are the original dumps from the MC9S12HZ256
1 is the eeprom part and the other the full flash

cheers :beerglass:

[PremierD]

Tip .. it's only the EEpom that you can adjust mate .. UPA will not write the flash so its not needed

[PremierD]

Yes I'll post them now. I would like to know where I went wrong. Thank you


You seem to be missing part of your dump mate ..
program eeprom with the attached file .. should be 8k on the button .. your miles bit was close though ..

[chrismoore02]

Thank you I'll reprogram it on Sunday and post results. :D

[chrismoore02]

Works perfect 7999miles dont know what happend to my 8k dump (think i was rushing as it was late at night)

[PremierD]

Works perfect 7999miles dont know what happend to my 8k dump (think i was rushing as it was late at night)

Damm ... 1 mile out ...lol

[z786]

Damm ... 1 mile out ...lol

you want me to send u a pencil sharpner?

[buga37]

Works perfect 7999miles dont know what happend to my 8k dump (think i was rushing as it was late at night)
What calc did you use?
"Tachosoft worked out just fine"

[chrismoore02]

Tachosoft. My calc was ok but as you can see from premierd's post part of my dump was missing

[buga37]

Tachosoft. My calc was ok but as you can see from premierd's post part of my dump was missing
i tried to read my with xprog-m clone but it would give me errors but i saved file anyway then i tried carprog clone and it worked ok but im afraid to write file back on it with carprog i don't know if i can trust it yet, just got it a few days ago and still testing it, so far so good
here is my file with 22000mi i would appreciate if you post yours so i can compare it
thanks

[chrismoore02]

On the other posts you say you have sorted it ?

[drpeter]

i tried to read my with xprog-m clone but it would give me errors but i saved file anyway then i tried carprog clone and it worked ok but im afraid to write file back on it with carprog i don't know if i can trust it yet, just got it a few days ago and still testing it, so far so good
here is my file with 22000mi i would appreciate if you post yours so i can compare it
thanks


Dump is corrupt....

[Music73]

i tried to read my with xprog-m clone but it would give me errors but i saved file anyway then i tried carprog clone and it worked ok but im afraid to write file back on it with carprog i don't know if i can trust it yet, just got it a few days ago and still testing it, so far so good
here is my file with 22000mi i would appreciate if you post yours so i can compare it
thanks

Was this dump from xprog or carprog... I used carprog through obd and worked no problem... Read and write....havent got dump to hand to upload but was fine....

Music73

[buga37]

carprog verified ok but i still dont trust it, i saved xprog-m dump too and compared them, it doesn't look good
do i have to pickup mcu legs or get the Cristal out?

[buga37]

On the other posts you say you have sorted it ?
i did, with miles calculation

[PremierD]

Aren't you afraid some one will steal your dump mate .. I mean no password .. lol

[buga37]

Aren't you afraid some one will steal your dump mate .. I mean no password .. lol
its corrupted anyway, ill just delete it

[buga37]

just tried both carprog and xprog-m with 12volt powered and dumps looks same, xprog-m didn't give me any errors.
here is the files

[buga37]

loaded files back on with xprog-m 12volt powered, works good
thanks everyone who "helped"

[smokey08]

loaded files back on with xprog-m 12volt powered, works good
thanks everyone who "helped"

Yes my xprog always needs external power with this dash. did you select the proceccor or just pick 9s12 eeprom and let xprog decide which one is inside? all the ones I have done have all been hz128 mcus.

[buga37]

Yes my xprog always needs external power with this dash. did you select the proceccor or just pick 9s12 eeprom and let xprog decide which one is inside? all the ones I have done have all been hz128 mcus.
i did select hz256 eprom non secure