vito 2004 ezs 68HC9 (08) AZ48A 1L02M

[kitachu]

Hello! Could some confirm if that's dump ok ?
I read it with xprog m like 908AZ32A 1L52H
Millage is 411592km.

Sec bit is DF-C8-EA-48-EA-48-EA-48
Thank you

edit
with carprog i get identical dump (short one)

[kitachu]

solved:beer:

[drpeter]

solved:beer:

How did you solved it? Please post ''solved'' dump.

Thanks.

[kitachu]

I suppose is good. I first read it with xprog, after that with carprog, dump was same. When i put dump in licnizk4 , not 4.8 i see where he wants to edit dump. I saved that dump and copied from my orginal in "same place" where liznick wants to edit. When i do that liznick read orginal millage.
So i found where is millage stored and put 000000 in that place.


edit: part with xxxx is VIN,ignore difference in that place

[milesbetteroff]

Hi mate it's nice when you fix it on your own a sence of achievement well done : )

[kitachu]

This was my first experience with ezs and service assyst :embarassed:

[MarkPRP]

did you read this HC08 Off the EZS or In circuit?

[kitachu]

In circuit, xprog (4.5) and carprog ,both read it same. Programming was with carprog i do not know if xprog would programm correctly.

[drpeter]

In circuit, xprog (4.5) and carprog ,both read it same. Programming was with carprog i do not know if xprog would programm correctly.

I had same EZS (1L02M) today and managed to do this EZS with UPA (external power, autobaud).

Just connect 5 wires

processor pin 2 - IRQ
3 - RESET
21 - VSS I connected power like diga
22 - VDD -------------------------------
26 - PTA0

Fill in security bytes, mileage was on other location then the version above (30 till 37 fill with zero);

mine sec. byte where; DA-AC-E5-2C-E5-2C-E5-2C

Info for everyone who has troubles with diga and this EZS version. Diga reads wrong value. Many versions available.

See picture for settings.

Good luck.

[alimmo]

In circuit, xprog (4.5) and carprog ,both read it same. Programming was with carprog i do not know if xprog would programm correctly.


Thanks for the info mate ,but can you tell me how many wires you connected using xprog in-circuit and which pins you lifted on mcu please.

Many thanks again

[kitachu]

I used standard connection from xprog manual without lifting pins.

[alimmo]

I used standard connection from xprog manual without lifting pins.

Can you also tell me if you used the usb to power Xprog or external power plug

Thanks mate

[kitachu]

I am using external stabilized supply 18V, powering only when programing.

[diagnoza_auto2000]

Wich software can calculate km in vito EZS?

[drpeter]

Wich software can calculate km in vito EZS?
You can write a UPA script...

[diagnoza_auto2000]

You can write a UPA script...

Can i use this script with etl?

[drpeter]

Can i use this script with etl?

No you can only use it to adjust mileage by dump if you don't have UPA.

[jarfm]

I had same EZS (1L02M) today and managed to do this EZS with UPA (external power, autobaud).

Just connect 5 wires

processor pin 2 - IRQ
3 - RESET
21 - VSS I connected power like diga
22 - VDD -------------------------------
26 - PTA0

Fill in security bytes, mileage was on other location then the version above (30 till 37 fill with zero);

mine sec. byte where; DA-AC-E5-2C-E5-2C-E5-2C

Info for everyone who has troubles with diga and this EZS version. Diga reads wrong value. Many versions available.

See picture for settings.

Good luck.


Hi, I used this security bytes and connection as above, and my UPA (ori) shows me AD AD AD AD AD.......
Please help me...

[drpeter]

Hi, I used this security bytes and connection as above, and my UPA (ori) shows me AD AD AD AD AD.......
Please help me...


try one ot these

0: 'DA-AC-E5-2C-E5-2C-E5-2C' );
1: 'DF-C8-EA-48-EA-48-EA-48' );
2: 'DA-A7-E5-27-E5-27-E5-27' );
3: 'A7-05-A6-58-A6-58-A6-55' );
4: 'DC-A0-E7-20-E7-20-E7-20' );
5: 'DC-A6-E7-26-E7-26-E7-26' );

[jarfm]

try one ot these

0: 'DA-AC-E5-2C-E5-2C-E5-2C' );
1: 'DF-C8-EA-48-EA-48-EA-48' );
2: 'DA-A7-E5-27-E5-27-E5-27' );
3: 'A7-05-A6-58-A6-58-A6-55' );
4: 'DC-A0-E7-20-E7-20-E7-20' );
5: 'DC-A6-E7-26-E7-26-E7-26' );

THANX A LOT!!! The second one works !!!
GREAT MAN!

[jarfm]

It's me again :)

Now is the other problem. Dash has 25LC640 and I don't have calculator fot It. (Licznik 4.7 has only 95080)
Dash has 111 590km, need 100 000km.
Thanx in advance

[jarfm]

It's me again :)

Now is the other problem. Dash has 25LC640 and I don't have calculator fot It. (Licznik 4.7 has only 95080)
Dash has 111 590km, need 100 000km.
Thanx in advance

Again problem solved. I used UPA script. Works 100%

[jarfm]

I think I vahe bad luck today....
I changed mileage in dash and EZS, put them back to car, and still shows me old mileage...
I'm confused... Is there other place where mileage is stored???

[drpeter]

I think I vahe bad luck today....
I changed mileage in dash and EZS, put them back to car, and still shows me old mileage...
I'm confused... Is there other place where mileage is stored???

How did you changed the ezs and cluster? Sent me the dumps I think you made a mistake.

[jarfm]

How did you changed the ezs and cluster? Sent me the dumps I think you made a mistake.

There are the dumps

[exe123]

you have not changed the km in ezs. that was wrong :)

0703110703110703 is km

[jarfm]

Yes, that was the problem.
Thanx to ALL

[gedas8899]

Hello guys, wher i can get upa scripts?

[iurcaberciu]

hello ,please hellp for corect. km. my ezs is temic 288 102 06 . car is vito2007 yar. this ezs contains 2 procesor . 08 masc 1l02m . how corect. read first procesor

[kalin]

the km are stored in procesor with mark R1!

[charlie-h]

Chaps, i am trying to read the same chip on vito ezs with xprog-m.
I have gone straight on to the chip with grabbers for my connetions.
I can get a read with xprog but the bin file is full of AD AD"S.
I have tried all the security bytes listed on this thread bt still no luck.
To check my programmer and connectors i quickly swopped them on to a merc wsp chip and it read it perfectly.
Any thoughts any one?

[kevfield]

Have a look in my post about reading this mcu it sould help

http://www.digital-kaos.co.uk/forums/f178/hc08az32-mask-0j66d-222433/#post1232382

Thanks kev

[charlie-h]

Kev thanks for that, but reading and writing the MC68HC08AZ32A for sprinter wsp is not a problem with my xprog-m.
Reading this thread it appears that the mcu for the vito EZS can be read with the xprog-m and read as MC68HC08AZ32 with mask 1L02M although this is not mcu fit to this board.
Maybee i am not following the info correctly but when i read with xprog the data comes back AD-AD-AD-AD-AD all the way down the read.
I have tried all the security bytes in the thread but still the same result.
In the thread someone has read this mcu with xprog so it appears it can be done.
As stated earlier i am useing the same pin outs as MC68HC08AZ32A with xprog diagram and going straight on to the mcu with grabbers.
If any one has a diagram, photos, or more info, this will be good!

[Pzolee]

Hi. I have this file 423375km, please mak it 0km.
EZS Version 1L02M V8
Thanks

[vageric]

Hi. I have this file 423375km, please mak it 0km.
EZS Version 1L02M V8
Thanks

try this one.

[Techhead]

Hi,

i have a key that will not turn, i've bought a new ezs and swapped the data over from 1237626L02M to the mcu's on the new EZS and the fault is now identical with the new EZS??
If i press the key buttons while attempting to turn the key it will eventually turn??? i've tried a new ESL and this has made no difference and i also made a new key??
My guess is maybe the data on the MSU's is corrupt?? Can someone check them or shed any light on my situation please? I've attached both R1 and R2 dumps.