DCM1.2 conections help

[daniellol]

Hello. I nead help with dcm1.2 renault clio 1.5dci. I have st10flasher and xprog-m. I dont know were i must connect the wires on the pcb to read the ST10f280. Please help me. Best regards.

[dof]

Hi, I just work in it some days ago.
You can read it via k-line KKL cable and use st10Flasher (that I can't arrive to use it).
You must solder 1k between red dot and ground...

See picture... St10Flasher see my ST10F280 but I can't save dump, only on screen...


Tell me more if you can have more.

Dof

[daniellol]

I will try tomorrow and post the results. Best Regards.

[daniellol]

Hello. I solved the problem. When I use ST10Flasher version 2.4B i can't read the flash dump to hex file. I only can write the flash dump as text file. On windows 98 i got run time error 48. I found ST10Flasher version 2.02. This version works fine on windows xp. The flash dump reads to hex file without any problems. I write the readed flash to other ecu dcm1.2 i got two same ECU's. Both ECU's works fine, I tested today. Thanks for help. I post here the St10flasher version 2.02 and readed dump file. Best regards.

[baccouche123]

hello all how to read the st10f280 with XPROG-m
. Urgent plize les pin conectore .et merci

[baccouche123]

dcm1.2 plize .

[baccouche123]

hello dof. thank you for this message. yes I am still with
dcm1.2. I took home a new computer renault
May the same problem prechofage lamp and does not s'alume
same lamp of Cheka. Pliz help me

[baccouche123]

hello to all. I still have a problem. I buy one
dcm1.2 virgin cheap renault. but do not smith
. Brogrammer I try to clip renault. It requires a
Code 10 chifas alphanemerique. (technical definition
vehicle). quelq'un help me if you like it

[3abas27]

hello to all. I still have a problem. I buy one
dcm1.2 virgin cheap renault. but do not smith
. Brogrammer I try to clip renault. It requires a
Code 10 chifas alphanemerique. (technical definition
vehicle). quelq'un help me if you like it
thnaks to this helfull information

[darwins]

Hello Friends

This is very helpfull can anyone shed some light on what ready made interface will work with this?

Or is it better to make the K Line 925 in the rar above ?

Maybe Xprog can be used ?

Thanks guys.

Darwins

Update: Made a flasher interface using the 925 diagram it works perefectly, even managed to utalise an old China OpCom housing :)

[javiercj]

Hi, I just work in it some days ago.
You can read it via k-line KKL cable and use st10Flasher (that I can't arrive to use it).
You must solder 1k between red dot and ground...

See picture... St10Flasher see my ST10F280 but I can't save dump, only on screen...


Tell me more if you can have more.

Dof

Hello

I have the same unit delphi.
but I need to connect to read the micro st10f280-b3 (991de) of ecu delphi

the switchboard is a Renault kangoo 1500 dci year 2007

the switchboard is delphi ref: 8200513076 - 8200582518

have tried to load cartography in the flash of the micro for obd and have blocked the ecu.

this ecu stores and save the flash and the eeprom in the micro

I have No car, so I can not do so by OBD and I need to load a new cartography through the micro.

the micro is not motorolla but ST reference: st10f280-b3 and mask 991de

in the micro can read the flash and the eeprom with programmer xprog - m

to make sure the connections and pinear in the right place and not annoy the micro. I've taken the micro data sheet and it does not coincide me.

as you've connected to read this micro and be able to read with the programmer xprog-m and make sure that forms the connections?

I hope your help

many thanks

[bokilee]

Hi, thanks for the informtion daniellol & dof. Flasher works perfect.

Best regards,
bokilee

[afcarservice]

Hello,
I need virgin dump for ECU Deplphi DCM 1.2.ECU is from Renault Scenic.