Reanult Koleos 2.0 DCi ECU BOSCH

[kikikis2001]

Hello, could Somebody help me understand what I need to read/write eeprom/flash of ECU from Reanult Koleos 2.0 DCi BOSCH 23710 JG70A (lower is written 23710 JY08D). Inside there is processor SC667035MZP66, 4L05S, UQMZXX1012, SGWFQ and lower is chip NEC B58944, D432568GU-70Y. Part nr is 0 281 014 360. On BDM page BDM100 module (http://www.evc.de/en/product/ols/bdm/) there is no info about such a prcessor, the same on page of magpro2.Mayby Somebody know how to read it (I would like change data inside only)? Best regards.

[ecutuner]

This must be EDC16CP33 with Pass-protected Flash... BDM100 cant do it!
Newer MPPS (clones 5.x upwards) should so it (never tried a clone, Byteshooter original will do it, CMD original too but cloned BDM100 1255 not!)

[kikikis2001]

Hello, thank You for answer. I've also think that it is EDC16CP33, but MPPS only read flash (I need to change data number inside), so it don't help me. Byteshooter can't do it now - http://byteshooter.net/Donwload_BS_CAR/Car+Trucklist%20V3.20.pdf (it is link to car list v.3.20) - mayby in future:) CMD not work with it now, but it probably the same as with Nissan EDC16CP33/C66, so it will be added - http://www.cmdtec.it/downloadfile.asp?file=carlist.pdf. But do You think that processor SC667035MZP66, 4L05S, UQMZXX1012, SGWFQ is MPC562 (but there should be also flash M58BW016DB or Am29BDD160, but I never see it on picture -mayby from other side PCB, but I'm afraid to broke)? What do You think about magpro2 BDM (EDC16 CP33 is in car list MAGP1.4 MAGPro2 BDM PROGRAMMER - Kayako SupportSuite Help Desk Software (http://magpro2.helpserve.com/index.php?_m=knowledgebase&_a=viewarticle&kbarticleid=17&nav=0,23)) - mayby it will be better? Or mayby Xprog-M with BDM adapter? I don't know what to choose? I want write new nr inside only. Best regards.

[ecutuner]

Hello,


its MPC 564, only buildin flash - password-protected. Byteshooter should do it (read/write OBD), my EVC BDM (original!) does this too!

You can try to read/write as the Nissan, its the same engine, and often the ECUs are the same!

[kikikis2001]

Hello, thank You for answer. I was writing that Byteshooter can't do it because there was "-" about this engine in car list 3.20 (in Nissan and Renault CP33), but mayby it should as You've written. About BDM, it means that if I will have original BDM 100, I could do it by http://www.evc.de/ftp/bdmToGo/Bdm_To_Go.EXE software? Could You only write what do You think about magpro2 BDM- because I would like buy one of these (BDM 100 or magpro2 BDM)?
Please write me also about change ID inside - which tool will be better (as I know I need to read full memory than change ID and save back). But I don't know how to change ID (because probably there will be problem with checksum) - or mayby I could use Ultraedit for it? Or mayby one of these devices could change ID on-line (without reading and saving all memory)? Best regards.

[ecutuner]

Hello,


personally i prefer original BDM100 vom evc, but if you use bdm2go your files (that you readout) are crypted and can only be decrypted with genuine winols!

which ID do you want to change, VIN? or ECU-ID?
VIN is in normally in EEPROM, ECU-ID in flash or CPU

[kikikis2001]

Hello, thank You for answer. I was thinking about VIN. As I see BDM interface will be not enough - I need winols also (to change VIN). The same problem will be with magpro2 - I need master version of interface to change VIN (files won't be crypted) - slave will bo not enough. But mayby I could change VIN without reading all eeprom (mayby there is in software option "chnge ID")? Or I need to read/write all eeprom - if I have master version, I could change in Ultraedit (not crypted redaout), but if I have slave I need winols (crypted) - am I right? Best regards.

[delio78]

I had a similar problem with edc16 from nissan qashcai 2.0dci
my BDM not found FLASH my ecu is same as the picture
BDM found MPC
I dont know where problem

Best regards

[kikikis2001]

Hello, mayby magpro2 BDM could read it - I think that it is EDC16CP33 - so in software should be two possibilities of reading falsh: Am29BDD160 or M58BW016DB (or mayby I 'm wrong). I don't know how to change VIN inside it yet:) I would like to buy BDM 100, but if You are writing that it is impossible to read flash, mayby better will be buying magpro2 BDM v4? Best regards.

[mvekaz]

I tried with BDM100 clone, this is log.
ECU is Bosch 0 281 013 364 19 05 2009
CMD ? Technologies srl - MPCProg

Ver. 3.1.0.1255 Dongle ID: 192 Date: 20.7.2008 18:42:12
Firmware Revision V.01 SN: 0258
Mpc5xx family x00020020
PartNum: Mpc561/2 x00000035
Flash EEprom identified: M58BW016xB
Family identified: BOSCH EDC16+ CP33 Renault
+12Vcc On
Ready...
Reading M58BW016xB
Mpc5xx family x00020020
PartNum: Mpc561/2 x00000035
Reading Block at 00000000
Reading Block at 00010000
Reading Block at 00020000
Reading Block at 00030000
Reading Block at 00040000
Reading Block at 00050000
Reading Block at 00060000
Reading Block at 00070000
Reading Block at 00080000
Reading Block at 00090000
Reading Block at 000A0000
Reading Block at 000B0000
Reading Block at 000C0000
Reading Block at 000D0000
Reading Block at 000E0000
Reading Block at 000F0000
Reading Block at 00100000
Reading Block at 00110000
Reading Block at 00120000
Reading Block at 00130000
Reading Block at 00140000
Reading Block at 00150000
Reading Block at 00160000
Reading Block at 00170000
Reading Block at 00180000
Reading Block at 00190000
Reading Block at 001A0000
Reading Block at 001B0000
Reading Block at 001C0000
Reading Block at 001D0000
Reading Block at 001E0000
Reading Block at 001F0000
Chk8:5EB2 Chk16:AFC4 Chk32:F22AC074
Total time: 01:15 sec.
OK
Reading M95xxx/AT25xxx Serial E2Prom...
Mpc5xx family x00020020
PartNum: Mpc561/2 x00000035
Reading Block at 0000
Reading Block at 0100
Reading Block at 0200
Reading Block at 0300
Reading Block at 0400
Reading Block at 0500
Reading Block at 0600
Reading Block at 0700
Reading Block at 0800
Reading Block at 0900
Reading Block at 0A00
Reading Block at 0B00
Reading Block at 0C00
Reading Block at 0D00
Reading Block at 0E00
Reading Block at 0F00
Chk8:2FCB Chk16:BF20 Chk32:01957C80
Total time: 00:06 sec.
OK
Wait Please
+12V OFF

[grinovsky]

Family identified: BOSCH EDC16+ CP33 Renault
wrong identification
this is BOSCH EDC16C36 and not EDC16CP33
the car is renault master 2.5 DCI
the flash is in M58BW016xB

[mvekaz]

yes, identification is wrong, but I read eeprom and flash .

[ecutuner]

Have you had a look into the file?

If it was read properly (what i dont think) you will get problems when writing it back into ecu or at least at checksum!

[mvekaz]

Here are dumps. Take look by yourself.
ECU is Bosch 0 281 013 364
MCU is SC667035MZP56, 4L05S.
I don"t know type of car.
wbr

[ecutuners]

Here are dumps. Take look by yourself.
ECU is Bosch 0 281 013 364
MCU is SC667035MZP56, 4L05S.
I don"t know type of car.
wbr


Flash read is good, all chks ok

[autosuper]

In Master , Traffic 2.5 DCI reading , writing and checksum calculating via BDM working good , without any problem . Problem is with 2.0 DCI in Laguna , X-trail etc. BDM not reading and not writng this ECU !

[darwins]

0 281 014 360
EDC16CP33-6.7
23710 JY08D

Hello Guys

I have this 23710 JY08D CMD BDM100 clone can not ident so reading eeprom / flash independently I can not do..

Clone FG Tech V54 does not recognise either :(

Genuine Xprog can read the eeprom but can't access the S29CD016G0PQAM01 flash. Can anyone tell me what genuine / clone is working for this ECU please.

WBR

darwins

[darwins]

I have the same problem as Post #8 by delio78 only eeprom can be accessed via bdm the flash is not identified I have tried various resistor removals in case there is a hardware ground link for example stopping connection, datasheet link (http://pdf1.alldatasheet.com/datasheet-pdf/view/102728/SPANSION/S29CD016G.html)attached if anyone is interested.

Maybe there is a quirk to reading / writing this ecu or we have 2 identical fails maybe one day some one else can update this post if they have success. :)

[slowgrind]

Hi,

Which BDM adapter is required for this SC667035MZP56 bosch ECU? How many legs are required? I cant read it with 8 legs with 2 legs missing second column from right.

Thank you