fiat marea need help

[latino]

hi m8 im try read kms on this dasch but i try with-- dsp,x prog,upa ....and no positive match ...its motorola XC68HC705E6...MASK 2F75B.. could some one help i dont no if i used the correct conection the only mask i found is (1F75B) i send the fotos with motorola and dasch thanks for help

[pepi]

You can do it with UPA. Raise pins 1(irq), pin 12 (pb0) and pin 15 (pc3).

[newgeniehex]

You can do it with UPA. Raise pins 1(irq), pin 12 (pb0) and pin 15 (pc3).
hello
i try to read after i have raise the 3 pin
i have no response ??????
how you can connect and read whit upa this componement 68HC705E6 MASK 2F75B
Do you have a picture please
in the menu mcu mottorola i use 68HC05E6 or other
Can i read in circuit ?
many thank in advance

[newgeniehex]

hello
i try to read after i have raise the 3 pin
i have no response ??????
how you can connect and read whit upa this componement 68HC705E6 MASK 2F75B
Do you have a picture please
in the menu mcu mottorola i use 68HC05E6 or other
Can i read in circuit ?
many thank in advance
help me please i find in the forum this picture for connection but i cannot read device nor respond i use in the menu UPA 68HC05E6
i put the picture and my connection
regard

[newgeniehex]

hello
no one have alredy read this mcu whit upa usb?
help me please
regard

[exxl]

do you have diga consult? this dash is easy to do with it ...

[newgeniehex]

do you have diga consult? this dash is easy to do with it ...
hello
i have remove the mcu
yes i have diga clone but my cable P 406 don't work i have alredy try to read tacho 406 peugeot jaeger i cannot find the good value ,and i use upa and i have change the mileage whithout problem
regard
some one have a good schematic of cable P406
many thank in advance

[knok]

hello
i have remove the mcu
yes i have diga clone but my cable P 406 don't work i have alredy try to read tacho 406 peugeot jaeger i cannot find the good value ,and i use upa and i have change the mileage whithout problem
regard
some one have a good schematic of cable P406
many thank in advance
your pictures is used for reading this kind of mcus with old motorola cracker software , but can be used also with UPA >
68hc705e6 // so 28 connection
--------------------------------------------
RESET (2) to RTS
PB0 (12) to TxD
PB1 (11) to RxD
IRQ (1) to 12V through a 10k resistor
PC2 (16) to +5V through a 1k resistor
PC3 (15) to GND through a 1k resistor
PC4 (14) to GND through a 1k resistor

PG0/AD0 (6) to +5V thru 560
VrefH (7) t0 +5V thru 10k

pay attention at correct quartz selection. This mcu works well with Q=2MHz.

[newgeniehex]

your pictures is used for reading this kind of mcus with old motorola cracker software , but can be used also with UPA >
68hc705e6 // so 28 connection
--------------------------------------------
RESET (2) to RTS
PB0 (12) to TxD
PB1 (11) to RxD
IRQ (1) to 12V through a 10k resistor
PC2 (16) to +5V through a 1k resistor
PC3 (15) to GND through a 1k resistor
PC4 (14) to GND through a 1k resistor

PG0/AD0 (6) to +5V thru 560
VrefH (7) t0 +5V thru 10k

pay attention at correct quartz selection. This mcu works well with Q=2MHz.
HELLO
many thank
i have make a schematic can you see and confirm if it is ok

i have interface whit tx and rx communication for change the meleage on P 206 OR SAXO and the soft motocracker have you too a good connection please for try to read this mcu

regard

[newgeniehex]

HELLO
many thank
i have make a schematic can you see and confirm if it is ok

i have in:beer:terface whit tx and rx communication for change the meleage on P 206 OR SAXO and the soft motocracker have you too a good connection please for try to read this mcu

regard
HELLO
thank to all :beer:
i have read whitout probleme
the car have 307536KM NYO4 find 307520 I need 170000KM
i have change the mileage and when i compare the file i find a stRange dump
it is normaly
many thank in advance for your answer
regard

[newgeniehex]

HELLO
thank to all :beer:
i have read whitout probleme
the car have 307536KM NYO4 find 307520 I need 170000KM
i have change the mileage and when i compare the file i find a stRange dump
it is normaly
many thank in advance for your answer
regard
HELLO
Solved my dump modified work perfect!
:beer::party:

[gaversa]

Modify rows 0020-0030-0040 and kilometaje0050-0060-0070 that you want to put up the reading.