CARPROG FULL

[speedy100]

313133313133

For all, if you want to see any format .lay very simple program. Open .lay view and stamp.
Tks for pass.

What is .lay format???

[diagtech]

can i have pass thanks

[honingkoning]

Guys i have my carprog, i made the 74hc125m mod i can read eep good (only tested out of circuit).
But when i connect to eep of a airbag module, it reads, finds and clear crash but file is the same!!!!!!!!!!!! nothing changes.

When i program eep with self mod file it writes good, so i think there is something wrong with the software?
could this be true, i am on 4.52.

Could someone share the latest possible sw.

Wbr Adam.

[Faraday]

you have 4.01 - try upgrade to 4.74

[honingkoning]

you have 4.01 - try upgrade to 4.74

I Will search in this topic, is this already posted before ?

Wbr Adam.

[honingkoning]

Could someone post 4.74 soft.
I could not Find it,

Wbr Adam.

[TMRaja]

Hi My friend can I have pass please

[autocargo]

Could someone post 4.74 soft.
I could not Find it,

Wbr Adam.

You''ll need firmware as well... Here is it.

[honingkoning]

You''ll need firmware as well... Here is it.

Question, is There a way to check what firmware i have ?
This CP is bought 1 Month ago from CN and its a no token version.
Will it cause any damage to my unit if i use it with my Firmware?
Or Will this affect my activations Or my CP.

Wbr Adam.

[Faraday]

simple 4.01 about 200 tokens and problems with eeprom reading, 4.74 about 20-25 tokens most functions work.

[justy22]

I Bought a clone CP when first came out, can it be modded and run with latest software, i see the posts about modding the board but what is actually being done to it

[autocargo]

Question, is There a way to check what firmware i have ?
This CP is bought 1 Month ago from CN and its a no token version.
Will it cause any damage to my unit if i use it with my Firmware?
Or Will this affect my activations Or my CP.

Wbr Adam.

If you already use it few times and no counter coming up I assume you have firmware 4.01. No damage if you use it with higher software, but nothing to gain... you won't have any extra functions because is old firmware on your CP.

[DashProg]

Hi M8
Please i need firmware 7.28 for my carprog to update it any one can help please

[pike]

Hi M8
Please i need firmware 7.28 for my carprog to update it any one can help please

The firmware can be the owners of a сhinese clone 7.28 for resetting counters, I think.

[DashProg]

I've a carprog 4.01 I want upgrade it to 7.28 that's why I'm asking for the firmware please any help any advice
thanks

[fuktak]

I've a carprog 4.01 I want upgrade it to 7.28 that's why I'm asking for the firmware please any help any advice
thanks

In DK you can find firmware 4.01 and 4.74 for free and flash your device you can use with soft 7.28 i think.BR

[teerak2uk]

Can be used with 7.28 but activations will be no more than 4.74

[Mr BLACK]

someone knows what i have to change on carprog 7.28 clone to work with PSG16 CAN from Vectra c ( A1 cahange MCP2515 , A82c250 , Rezistors and capacitors position fixed , 10u /16v changed , carprog 5V and 3.3V regulators and capacitors )... Thanx

[XmoDDeR]

Ive seen new mcu with all features working 2 versions one with online functions working they say .

[teerak2uk]

Ive seen new mcu with all features working 2 versions one with online functions working they say .
Hi mate got a carprog which has kynar wire jumpers on board so maybe a newer version but won't connect to usb any ideas?

It's also slightly different to 4.01 pcb is this because it's a 4.74?

[Multipla]

Do you have a circuit to program At88 eeprom? Please if do you have can post here? It just also lays out file .lay or other pdf ecc. ecc.

[Nikola1309]

Hi I try to repair audi dash with 2j74y, and carprog said mcu not detected? Does somebody what is the wrong.

[Pali33]

this mean, that the MCU is dead. Or you have make a mistake at connections.

[Nikola1309]

ok, thanks. connection is ok, so mcu is dead. thanks.

[forumoto]

I once read from here, someone who has make a post of, how to flash CP without listing the 55pin, and he also made a switch for this, please i need the post # discussing this and also need some image backing this. I have realize that listing that 55 pin always could oneday break it finally, and it is very tiny to be playing around with.

[nounou31]

cool :canabis::canabis::canabis:

[Nikola1309]

I have problem with carprog, on usb power work ok and when i put external power said device not detected, i think that diodes are faulti.They have mark g4, whit what diodes can i replace it?

[grostoto]

Hello thank you for participating Value
I personally benefited from for repair this my carprog
Here I put between your hands carberg 7.28. It works 80 %
And the second has not used it very much and he is also a good
Thank you and I apologize for my writing bad
https://mega.nz/#!D88AwBqK!4ySZzeMxkq_EWHirIRKEq5PHIAJnJhLGq9xbPwQ P7ak

[pawel89]

Link dont active

[damian475]

What is the last working dump and lib file for clones 4.74, or something newer? ofcorse avialable for free.

[autocargo]

There's only 4.74 available for free.

[teerak2uk]

What is the last working dump and lib file for clones 4.74, or something newer? ofcorse avialable for free.
4.74 .

[kashalot]

It's about the adapter cable A11 which is functional from the two it comes to the pins 10 and 11 on the board DB25?
335657335658

[pike]

It's about the adapter cable A11 which is functional from the two it comes to the pins 10 and 11 on the board DB25?


Look here (http://codecard.lt/carprog/adapters/a11-bmw-ews-adapter/prod_82.html)...

[kashalot]

Thank you I've seen already that the tracks on the first image are all wrong?Must you cut and connect different?In the second picture she run properly?

[DashProg]

May someone can advice to me from where I can get a good J-tag

[kashalot]

You need not necessarily JTAG it port LPT COM also does what with USB runs is
J-Link interface V8 segger. I have programmed it with ExpressCard LPT.

[teerak2uk]

May someone can advice to me from where I can get a good J-tag
Just use 25 way plug with resistors

335785335787335788

[DashProg]

If the J-link can does the upgrade of carprog may someone show me connection if possible

[kashalot]

JLink V8 Schematic 335893

[hackbest]

Hola compa?eros CarProg tiene un problema con el clon 6.80 y probado con 7.28 y consigui? que estoy tratando de leer por obd2 microna campo de 2007 y no conecte alguien me puede ayudar o me diga por qu? no leer gracias y saludos



anyone knows whether to upgrade or to do something for the A1 wire work

[beats2006]

Hi,

I have clone carprog v7.28 and want to check if my a1 cable is working, what vehicle is best to test it is working on and how? I have few vehicles available such as BMW e90, Seat Ibiza, Transit Connect, Renault Kangoo, Fiesta??

[biktel]

Read pin from PSG16 or edc16


Sent from my iPhone using Tapatalk

[bodzio012]

ECU opel vectra c, zafira B

[yeager]

hi, i buy a new 7.28 china clone but it cant read eep 24Cxx, before have v4.31 it dont have problem whit eep, can anyone help me whit this?

[Music73]

hi, i buy a new 7.28 china clone but it cant read eep 24Cxx, before have v4.31 it dont have problem whit eep, can anyone help me whit this?
Probably needs rework... 7.28 isn't really any differant to 4.** versions just using newer software but still the same activations....

Sent from my SM-T533 using Tapatalk

[yeager]

what do you mean under rework?

[Music73]

what do you mean under rework?
Wants the gnds doing probably the driver chips changing... If you search it you'll find all the info...

Sent from my SM-T533 using Tapatalk

[lupu_sandu]

And you think that DK is ebay?

[Jashmine1983]

I have this error on A9 test and I don't know what might be the problem.
I've replaced all the HC's.
On D1 adapter test everything is OK.
371695

[Triniguy]

Hi everyone, I have original tool but don't get true with Elantra 2011+ via OBDII at all. Anybody has a solution???

I tried A1, A1+ actually all OBDII cable coming in full dash package from CC

Thanks

[Triniguy]

Hi everyone, I have original tool but don't get true with Elantra 2011+ via OBDII at all. Anybody has a solution???

I tried A1, A1+ actually all OBDII coming in full dash package from CC

Run all test, all good

Thanks

[TULGEYWOODMAN]

Have you asked carprog directly?
Ask for Lina

[Triniguy]

Have you asked carprog directly?
Ask for Lina

Yes I did. Communicate with Lina and support team.
She replied try other vehicle. I did 2009 Kia Sorento via OBDII, np. Also build test adapter and did test, everything good.
So she said may model not supported, but I see same panel on she side for Hyundai software.
I know china tools always promise to do all on the list but don't do......
Didn't expect that with original tool, so I thought I did something wrong........................................

[ubistvo]

PROBLEM


In all softwares witch i found no one work VAG EDC 16 ECU !!!!!
When i try to connect say
"No device attached" "Status: Waiting for commands" and for finish get me
message " ERROR" No device attached
I have a test several carprog softwares and no one work with VAG EDC
Is it possible that the Carprog can not work with VAG???
Have someone try this function on Carprog with VAG ECU???
Have someone have solution for this???

[shirokov]

Solution: you need CarProg A1 (http://www.codecard.lt//a1-a1-plus-new-generation-odb2-adapter/prod_516.html)+ (A1 PLUS) adapter for this option.

[TULGEYWOODMAN]

Ah well, never mind.........

[MMAAuto]

has anyone tried to do odometer correction on fujitsu MB91F060BS found in honda fit hybrid dash with v7.28 carprog chinese clone

[moi]

can A1+ adapter work with clone??
thanks

[FxShaw]

can A1+ adapter work with clone??
thanks

Yea it should be able to.

[mileage1]

ford transit 2013 will work?
thnx

[FxShaw]

2010+ with D70F3421+93C76 yup.

[mileage1]

2013 is 95320

[teerak2uk]

2013 is 95320
2013 can be either this is change over year

mk7 (93c76)

Custom (95320)

[nickolasd]

anybody knows if original carprog does Chrysler SRI?

[MV auto]

anybody knows if original carprog does Chrysler SRI?
no SRI function in carprog original.

[janake]

anyone have some info about CARPROG FULL V9.31

[ghostrider72]

Look on the developer site mate.

[ledong]

anyone have some info about CARPROG FULL V9.31
China clone newest with V9.31. I dont try it.

[rastus86]

has anyone tried to do odometer correction on fujitsu MB91F060BS found in honda fit hybrid dash with v7.28 carprog chinese clone

i would like to know this as well

[xlinuxasx]

Hello, I want to read my vw ecu, but in all Carprog versions Im trying, it is N/A. Is there any solution to make these functions working? Im using chinese clone. Thanks.

388387

[javyb]

Hello, I want to read my vw ecu, but in all Carprog versions Im trying, it is N/A. Is there any solution to make these functions working? Im using chinese clone. Thanks.

388387
Because there is no device attached look at screen bottom left should display serial number

Sent from my SM-G935F using Tapatalk

[xlinuxasx]

When Im connecting device, i got this message:
388390

[mara07]

It's will work with the adaptor A1+ .
And the firmware must be FULL
388412

[ubistvo]

OK
I need help
Passat B6 2007 i try to change km with carprog but all time i got message "connection error"
What is the problem??
Last year i try on similar B6 and i make change on km
What is now problem??

[lupu_sandu]

Adapter A1

[ubistvo]

OK
What adapter A1???
Can you help me

[lupu_sandu]

OK
What is now problem??

Adapter A1
You got your answer to the problem

[Seby_TM]

You need to check if you need power supply on carprog +12v !

[Bllinda]

Sorry for the question off topic. In order not to create a new ....
Is everything works car.prog 8.21and the9.31 off-line? Thx

[gokart]

I have UART1 - error during testing with A9 test adapter. Do you have any solution for this? It's original one and I have already replaced all 74HC125M.

[FxShaw]

I have UART1 - error during testing with A9 test adapter. Do you have any solution for this? It's original one and I have already replaced all 74HC125M.

Usually get that error if you don't replace the resistor too or solder wrong spot..Did you make the A9 adapter yr self?

[gokart]

Usually get that error if you don't replace the resistor too or solder wrong spot..Did you make the A9 adapter yr self?

Thank you for your reply. The resistors and soldering are OK. I made the adapter which is 100% correct. Finally, I solved the problem. It was a small manufacturing problem on the PCB. Now, works fine.

[FxShaw]

Thank you for your reply. The resistors and soldering are OK. I made the adapter which is 100% correct. Finally, I solved the problem. It was a small manufacturing problem on the PCB. Now, works fine.

Can we see a pic of that and where it was just in case someone else have the same issue in the future?

[Levanime]

Sorry for the question off topic. In order not to create a new ....
Is everything works car.prog 8.21and the9.31 off-line? Thx
+1 question not to create new thread

source to buy good quality car prog full?

thanks

[dodiss]

PROBLEM


In all softwares witch i found no one work VAG EDC 16 ECU !!!!!
When i try to connect say
"No device attached" "Status: Waiting for commands" and for finish get me
message " ERROR" No device attached
I have a test several carprog softwares and no one work with VAG EDC
Is it possible that the Carprog can not work with VAG???
Have someone try this function on Carprog with VAG ECU???
Have someone have solution for this???

Had the same problem with Carprog orig full. Carprog support asked to sent A1+ adapter for repair. After i got it back, everything with EDC ecus works fine.

[bolek9000]

Hello I need program to repair cluster dump odometer , I need change Vin number an language in the my megane2 1.5 DCI

[bolek9000]

I flashed 93C56 and my english language dissaperance

[biktel]

Hello I need program to repair cluster dump odometer , I need change Vin number an language in the my megane2 1.5 DCI

To change the language you need Can Clip and to change Vin you need to read eeprom and change manualy m


Sent from my iPhone using Tapatalk

[bolek9000]

I read eprom but my VIN is longer than originally, I've got one letter more, a find: repair dump dashboard scenic2 , I would like semi program for megane2 its enough for me

[bolek9000]

language must be changed in eeprom odometer, because, after change software in eeprom , my english language changed for france
Can you help me ?

[biktel]

Than change the eeprom first and than change language with clip


Sent from my iPhone using Tapatalk

[bendy]

I flashed 93C56 and my english language dissaperance
Post copy of 93C56 & then I can help

[atikah]

THANK YOU
FOR HELP

[dichos]

Hey guys. I tested the A1 adapter today. And as shown across the internet and on this forum, some resistors and capacitors where misplaced on the adapter. I fixed all of that. Now, I can connect, A1 adapter is working, and reading, but something is messed up.
The first time I tried, I got the correct PIN, Mileage was wrong, and VIN had some strange characters in it.
But in the dump file, I could find the correct VIN and PIN.
Then, when I tried reading again the data was repeating all over again, all I got was a part of the VIN and totally wrong Mileage and PIN. I tried maybe 30 times more and never got the correct PIN again.

What could this be? I'm trying to read Bosch ME7.6.2 - Corsa D 2008 Z12XEP.

Here is a pic of my adapter: (later I removed the Pin 16 wire, as it did nothing useful)
423987

Here is a pic of my CarProg:
423988

I tried everything, replacing MCP2515, caps, resistors, adding 120Ohm terminating resistor between CANH and CANL, but nothing. Again and again I only got a repeating part of the VIN all over the dump.

[tango]

the 47uf cap is wrong way round
gnd (white strip down side is gnd) this should be conected to the voltage regulator top but inside your + side is connected

[dichos]

Damn, I didn't even looked at it. Hahaha. I will replace it entirely. Thanks for noticing.

One thing I learned from this cheap-ass clones like CarProg, you better open it inside before even plugging it in. A1 adapter had mistakes, A4, A5 and A6 adapters were all miswired, they just randomly soldered the wires without even looking at the schematic. The main CarProg board has this grounding issue and this capacitor I didn't noticed. Retards.

[tango]

mine was exactly the same lol had to redo everything

[bearheroes]

Damn, I didn't even looked at it. Hahaha. I will replace it entirely. Thanks for noticing.

One thing I learned from this cheap-ass clones like CarProg, you better open it inside before even plugging it in. A1 adapter had mistakes, A4, A5 and A6 adapters were all miswired, they just randomly soldered the wires without even looking at the schematic. The main CarProg board has this grounding issue and this capacitor I didn't noticed. Retards.

The most important you should have learned is to buy ori tools...


Sent from my iPhone using Tapatalk

[dichos]

I replaced the capacitor completely. No change, it is still reading wrong data on Bosch ME7.6.2 Corsa D.

I would buy original tools if I fix cars for a living, a bought this device only to experiment on my car and learn some new things. I'm a student currently and no way I could afford to buy original tools only for using it with my car. :)

[tango]

maybe needs the 74hc125's changing or could be crystal
what fw is in the unit? (look at serial number)

[zolee33]

Hi,

I have a CP 8.21 online, fixed my antenna (replaced immo coil and changed some RC parts, works fine)
I bought a brand new ID48 transponder. How can i prepare for Golf 5 MY2004?
I want to create TP23 from ID48 and adapt with VCDS.
(sry my english is not very good)
Thanks

[javyb]

Can carprog v8.21 clone do dash swop on 2006 Audi A3 to a 2011 style A3 clock

Sent from my SM-G935F using Tapatalk

[antibisic]

I don.t think so it need online conection

[Avinitlarge]

Does anyone know if this Newest CarProg V9.31 Airbag Reset Tool Immo KeyPin Code Reader Radio MCU EEPROM (http://www.ebay.co.uk/itm/262855829926?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) will allow me to emulate CAN to test Volvo 2002 S60 DIM/Dashboard ??

[tango]

Does anyone know if this Newest CarProg V9.31 Airbag Reset Tool Immo KeyPin Code Reader Radio MCU EEPROM (http://www.ebay.co.uk/itm/262855829926?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) will allow me to emulate CAN to test Volvo 2002 S60 DIM/Dashboard ??

do you not read posts?
its all over the internet in many forums this version is really 4.01 hardware and nothing new

[Avinitlarge]

do you not read posts?
its all over the internet in many forums this version is really 4.01 hardware and nothing new

Ive done nothing but read. There is so much information, good, bad and outdated, I don't know what is what. I wanted to avoid asking. I just need to be able to use the emulator function to check Volvo Clocks/dashboard

[piter200]

Anyone tried the Nissan qashqai 2010+ by obd option for the 9s12 dash?

[nik6601]

Anyone tried the Nissan qashqai 2010+ by obd option for the 9s12 dash?

For me not working on Qashkai 2012 1.6dci by OBD.
Worked on Dacia Sandero 2012 and Renault Laguna 2010 by OBD .
Carprog clone 8.21 .

[dandyk]

Hi,
I have new clone from ebay. Why there is a lot of N/A?
Isn't it possible to do eg. Octavia II 2011?
Thanks,
Daniel

[mikroel]

Reno clio airbag ....496 doesn't work also


Sent from my iPhone using Tapatalk

[dandyk]

Hi,
I have new carprog clone and I'm not able to do any cars. Lot of "n/a" is mentioned. Golf V 2007 cannot connect it is not loading.
Is something needed to do with my car prog to work it right?
There was written it's version 9.31.. but ehm :-)
Br
Daniel

[Pyromaniak]

Hi,
I have new carprog clone and I'm not able to do any cars. Lot of "n/a" is mentioned. Golf V 2007 cannot connect it is not loading.
Is something needed to do with my car prog to work it right?
There was written it's version 9.31.. but ehm :-)
Br
Daniel


have you carprog device pluged into usb? see the device number? I can do carprog repair, im from czech too.

[garagesport]

Hello, I have the v9.31 and there are many cars that I can not do for example lagoon 3 megane 3 etc. Somebody help me almost all leave n / a

[Pyromaniak]

Hello, I have the v9.31 and there are many cars that I can not do for example lagoon 3 megane 3 etc. Somebody help me almost all leave n / a

try software v8.21

[Furkan sucu]

thans :D :burnout:

[garagesport]

Hello where can i download v8.21?

[Pyromaniak]

try google :D

[garagesport]

I downloaded one and requested registration key

[Pyromaniak]

I downloaded one and requested registration key

Copy your lib file to directory with downloaded carprog program :)

[garagesport]

Need of v8.21 cracked the ones I need serial

I need key and name to register the soft

[Pyromaniak]

https://www.uloz.to/hledej?q=carprog

[tango]

I downloaded one and requested registration key

then post the hwid it gives you and someone will give you name and key to activate

[electrones]

Hi friends


I have genuine CArprog and i need help to made a new or rework my antenna transponder to work without error or fault in readed

cheers

[Pyromaniak]

Hi friends


I have genuine CArprog and i need help to made a new or rework my antenna transponder to work without error or fault in readed

cheers

Hi i measure my antene from my clone and have 5 ohms... If you have not 5 ohms try to use from car(only wire ring)

[dandyk]

Hi,
was somebody succesfull with Golf 5 2007?I have clone one and it "cannot connect", do you have idea why? :-/
Thanks a lot,
Dan

[Seby_TM]

Hi friends


I have genuine CArprog and i need help to made a new or rework my antenna transponder to work without error or fault in readed

cheers

For genuine unit need to use coil with inductance aprox 400...500 uH with 7...10 cm diamerer of coil.

[mrchip]

Hi Mates
I want to rework my caprog ( 4.01) but I dont know what the values of the parts must be .can you please tell me which is right one ?
445840
1- KEMET T491C226K016AT Surface Mount Tantalum Capacitor, 22 ?F, 16 V, T491 Series, ? 10%, 2312 [6032 Metric]

2-
Tantalum Capacitor, 22 ?F, 16 V, T491 Series, ? 10%, 2917 [7343 Metric]

3-
Surface Mount Tantalum Capacitor, 22 ?F, 16 V, T491 Series, ? 20%, 1411 [3528 Metric]

445842
1- TEXAS INSTRUMENTS CD74HC125M Buffer, 74HC125, 2 V to 6 V, SOIC-14

2-FAIRCHILD SEMICONDUCTOR MM74HC125M... Buffer / Line Driver, 74HC125, 2 V to 6 V, SOIC-14

[Jindrisak]

Hi,
i have problem with my carprog. It didnt read anything. After replace all 74HC125 read 24c and HC-motorola perfectly. But still wont read 93c. It show "No chip detected".
Thanks for any helpfull reply.

[gilahish]

................

[wokcz]

So what would be better, adding 4x 74hc125 on top of the existing chips (to have 8x 74hc125), or replacing them with 4x 74hcT125?

[crazylou2017]

Hello where can i download v8.21?

http://www.obd2vip.com/html/carprog-full-v821-software-free-download-27551.html

[BRMTDI]

Anyone know a good source for carprog....? My Last unit I am having issues I get mismatch error or something when I change the LIB to match the device.

[dadal]

please check this pinout ( carprog manual HC05B6 / B8 )
need I to some pins lift up ? or bridge ?
I want to read/write golf3 immo box,

[gilahish]

Hi, try to read hc05x32 (d69j), i get only FFFFFFFF, didnt have any problem with other chips. have special hc05 adapter, maybe something in settings?

[Seby_TM]

Hi, try to read hc05x32 (d69j), i get only FFFFFFFF, didnt have any problem with other chips. have special hc05 adapter, maybe something in settings?

How you try to read this mcu, in circuit by programmer ? in what module it is this MCU ? or out from pcb in some adapter ?

Give more informations.

This mcu is with security, if you read only FFFFFFFFF mean you mcu now can be erased !

[vey81]

(http://codecard.eu/carprog/carprog-clone-legalization/carprog-clone-legalization-to-original-carprog-full-version/prod_1005.html)Hi all,
have someone experience with A1+ adpater "no device attached" problem?
Status: Carprog clone legalization to orig Carprog Full,
- test with A9 adapter all O.K.,
- A1 adapter without problems,
- A1+ ERROR: "no device attached".

Need read eeprom VAG EDC16 and without success...
Thanks for any advice how to get rid of it.
BR vey81

[vey81]

(http://codecard.eu/carprog/carprog-clone-legalization/carprog-clone-legalization-to-original-carprog-full-version/prod_1005.html)Hi all,
have someone experience with A1+ adpater "no device attached" problem?
Status: Carprog clone legalization to orig Carprog Full,
- test with A9 adapter all O.K.,
- A1 adapter without problems,
- A1+ ERROR: "no device attached".

Need read eeprom VAG EDC16 and without success...
Thanks for any advice how to get rid of it.
BR vey81

[aurelmarius]

Hi, i have 8.21 clone and tried to read immo data on 2007 octavia with micronas but without success. It reads the dash part number and then stucks. Any solutions ? Thanks.

[frankrayk]

Hello, my friends, I have had this problem with Carprog, I update the MCU with V8.21 and I use 150428CAR00542UA.Lib, Carprog works very well with few N / A, but it only works for about 15 minutes, then it's as if had lost the MCU's programming, no longer being recognized by the USB port.
I make a new recording on the MCU back to work, but for only 15 minutes + or - , getting only ????????????? in place of the numbering of the lib in the lower left corner of the program.

I changed the mcu for a new one, but it's still a problem.

[vaicekas]

Hello, my friends, I have had this problem with Carprog, I update the MCU with V8.21 and I use 150428CAR00542UA.Lib, Carprog works very well with few N / A, but it only works for about 15 minutes, then it's as if had lost the MCU's programming, no longer being recognized by the USB port.
I make a new recording on the MCU back to work, but for only 15 minutes + or - , getting only ????????????? in place of the numbering of the lib in the lower left corner of the program.

I changed the mcu for a new one, but it's still a problem.

After programming you connect the MCU's pin 55 to the ground? Can not leave not connected.

[frankrayk]

After programming you connect the MCU's pin 55 to the ground? Can not leave not connected.

I do this but it does not solve.

[vaicekas]

Then I suspect crypto AT88

[frankrayk]

Then I suspect crypto AT88

I think it can be put a 24c02 in place of the AT88 are the same datasheet, the hard is to find a good file.

[remolyy]

Hi. Guys. Some advice wich one of logics wuold be ok to rework carprog. Thanks
https://uk.rs-online.com/mobile/search.html?searchTerm=74HCT125

[Aislingob]

I bought carprog full and did the honest thing and bought the original item with all original leads 2370 euros with delivery costs, , then on my first job I read a ford airbag via obd when I go to clear the crash data I get asked for 30 euros ,how is anybody supposed to make profit , wud ye guys recomend Orange5 airbag calculators to run with this tool or what would ye guys advise me ??

[rjdosky]

Which version of carprog should i get that would reset crash from a 2012 nissan altima 98820zx50A & 2008 infiniti g37s coupe 98820JL00A please help

[Thor2]

I have a geniune carprog that I bought about 5 years ago, most of the functions have n/a cos I only purchased Audi RB4 function on top of the functions that came pre activated with the unit at the time.
Is there any way to activate all functions free or do I have to pay 1000 euro to codecard.

[James MR2]

Hi, have someone used Carprog online and sucessfully done mileage change on Audi Q7 2007 with Magneti Marelli cluster part number 4L0920930H erprom 95160?
I have saved the dump just in case.

[piter200]

Ford focus 2011-2013 with blue display and arrows. What to choose in carprog from OBD? I have 8.21 and later versions...

[maciek007]

I have problem with voltage D1 adapter test :

UART1 - OK
K Line 100k/5V - ERROR
K Line 1k/5V - ERROR
K Line 1k/12V - ERROR
K Line 100k/12V - ERROR

what should I replace in D1 or in CP ?

test with +12v 1,5A (its not too strong?)

[naprawa5]

Replace the npn and pnp transistors.

[maciek007]

Replace the npn and pnp transistors.

all in D1 ?
1E - BC847 ?
3F - BC857 ?

[Partymad09]

can someone could help me VIN CODE VF34C9HXC55272112 IM locking the pin or security code or pass keys is a 308 2008

[lynyrd]

Hello!
My carprog China clone, not write mileage.
He read and write eeprom 24,93 series,no problem.
Read correct mileage,but not write a new.
He is stopping on 100% and nothing....
After that the eeprom is empty.
I tested with some versions 7,8,9 nothing
Thanks.

[danngrigore]

Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanksi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanks

[drpeter]

Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanksi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
ThanksBUY ANOTHER ONE FOR 10 USD

[frankrayk]

Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanksi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanks

Reattach the firmware to AT91.
I already had Carprog that was good after the third attempt.

[danngrigore]

Thanks. Very kind of you. Is that the kind of advices you are playing around here for?

[mikroel]

Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanksi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanks

Wrong MCU


Sent from my iPhone using Tapatalk

[ubistvo]

Hello
Can someone tell me where to buy A1+ adapter for Chinese carprog??
Or how to make to read VAG EDC
Thanks

[vaicekas]

Hello
Can someone tell me where to buy A1+ adapter for Chinese carprog??
Or how to make to read VAG EDC
Thanks

A1+ clone not exist. Only original.

[oltianmunga]

Don't buy chinese crappy clones they are worthless already tried this and believe me even when the options are available the WONT WORK and that's all.

[irandias]

Anyone else detecting Trojan in all clone versions of "carprog.exe" and "carprog_online.exe"?

Trojan:Win32/Tilken.B!d
Trojan:Win32/Bitrep.A

[borshch]

I bought Chinese clone full carprog 3 years ago, junk.
thought maybe because it’s old,
bought another newer one few months ago, same junk, almost nothing works.

Bought original carProg with basic software, works good.

Dont waste time and money buying Chinese carprog clones, useless junk.

[wosi0]

100% Spot-On

[mikroel]

If you talk about Chinease clone that is true but ....

Clone can do many things, almost as original, if it is reworked well.

Also original carprog can’t do some things even they are listed .

So the things are not only black&white sometimes they are grey.



Sent from my iPhone using Tapatalk

[Kayhan 17#]

Well i bought one with newer software but it was hardware defective, then bought a second hand one which had older firmware, i updated with files from here and i could do RNS510 and Audi Symphony Radio Codes and an Airbag ECU so i can recommend a carprog clone.

[slklite]

Hello guys, does anyone know where I can download the most recent version of carprog cracked with all features activated ?

Or where I could download those features that need activation like vag edc16, peugeot valeo bsi ... ?

Thank you.

[Allky86]

Can some one make rework on my carprog

Poslano sa mog SM-G950F koristeći Tapatalk

[crazylou2017]

If you talk about Chinease clone that is true but ....

Clone can do many things, almost as original, if it is reworked well.

Also original carprog can’t do some things even they are listed .

So the things are not only black&white sometimes they are grey.

Sent from my iPhone using Tapatalk

Hello, would you please share me the tips on how to rework the carprogfull Chinese clone as carprogfull original?

[martij976]

I have carprog original and pulled it out for some job after an year..
It needed an update, otherwise won’t work... Can’t access the web updating page, so I contacted the developers with my serial number. Within 24 hours I got an reply and my carprog was updated and worked like charm.
That’s why I stuck with original!!
my 2 cents

[generalelect1]

Hello my clone works. the airbag-ecu and Dash how i have make works all.
Hello dear
i have too carprog clone
kindly give me software to reinstall it
chear

[MrBingo]

hello.I have successfully updated my carprog from 081105CAR001773I to online version 8.21. Now I have only one error with D1 adapter.

Carprog alone + A9 pass the test OK.
Carprog + A1 pass Test ok.
Carprog + A9 in Test D1 = all ok.
Carprog + D1 + A9 in Test D1 say errors

UART1: ok
K Line 100k/5v: ok
K Line 1k/5v: ERROR
K Line 1K/12v: ERROR
K Line 100K/12v: ERROR

Thank you..

[teerak2uk]

hello.I have successfully updated my carprog from 081105CAR001773I to online version 8.21. Now I have only one error with D1 adapter.

Carprog alone + A9 pass the test OK.
Carprog + A1 pass Test ok.
Carprog + A9 in Test D1 = all ok.
Carprog + D1 + A9 in Test D1 say errors

UART1: ok
K Line 100k/5v: ok
K Line 1k/5v: ERROR
K Line 1K/12v: ERROR
K Line 100K/12v: ERROR

Thank you..I think test don't work well with 8.21

[MrBingo]

I think test don't work well with 8.21

even with the software 4.74 it makes the mistake. or is it dependent on the lib file?

[wosi0]

CARPROG FULL ORIGINAL- only 1400 Euro, Christmas Promotion .

:listen: codecard webside

[u.s]

Buy standard and then upgrade to full, works out cheaper

[vangelis37]

Hallo marry Christmas
pls a need for becker radio be3100
Sn. 12894752
CODE?
Thank you......

[wosi0]

Try This 24433 or 62233

Please Rapport...

[carradio2001]

Hi and A Happy New Year !

Who can help me to make a carprog clone to work with this ?
http://codecard.eu/carprog/software/carradio/carprog-software-to-unlock-opel-gm-chevrolet-car-radio-and-navigation-by-obdii/prod_2681.html

Regards,
Carradio2001.

[golfather2]

Hi all

I have bought a Chinese clone -V10.93 but am using the 8.2.1 software on windows 7 64 bit. The issue I am having is reading 95320 eeprom from edc16 ecu. I am using the A6 SOIC8 clip for EEPROM programmer. I am powering the carprog unit externally as well. Any help or advice would be appreciated

[ryn079]

Try to desolder eeprom. Don't read it in circuit. No power supply to carprog is required for this operation.

[joker01]

verify this connection on connector.......

[golfather2]

Try to desolder eeprom. Don't read it in circuit. No power supply to carprog is required for this operation.

worked perfectly

[wosi0]

CARPROG FULL ORIGINAL- only 931 Euro, Easter Promotion .

:listen: codecard webside

[catalinosonesti]

hy,freinds how know if carprog original can make km by obd jeep patriot 2010 ?
tell to use this obd :http://www.codecard.eu/dash/chrysler-dodge-jeep-cantool-for-dashboards-and-immoblisers/prod_761.html

[Andr33iy98]

carprog v8.21 works with golf 5 variant 2009 year and golf 6 2011 year via OBD ?

[catalinosonesti]

Hi
I didnt manage to do dash km by obd ford kuga with carprog original V 13.20 , i use A1 multi ,A1 + Ford Volvo adapter , but no work to write new km , i have write error.
only select were i mange to read mcu 9S12 by obd it was Ford focus 9S12XHZ512 , but when write i have '' write error ''
For the future what is the procedure ? By codecard suport tell me to do this steps , read by obd then modify in DIrect conection , no chance ,no work .
Please how have more experience with Carprog ,to tell me what is the best and fast mode to do this kund of dash by OBD conectio ,or what toll i must to take for ford OBD 9S12 ..... TO WRITE NEW KM .
Best regrads

[teerak2uk]

Hi
I didnt manage to do dash km by obd ford kuga with carprog original V 13.20 , i use A1 multi ,A1 + Ford Volvo adapter , but no work to write new km , i have write error.
only select were i mange to read mcu 9S12 by obd it was Ford focus 9S12XHZ512 , but when write i have '' write error ''
For the future what is the procedure ? By codecard suport tell me to do this steps , read by obd then modify in DIrect conection , no chance ,no work .
Please how have more experience with Carprog ,to tell me what is the best and fast mode to do this kund of dash by OBD conectio ,or what toll i must to take for ford OBD 9S12 ..... TO WRITE NEW KM .
Best regradsWhat year is the car

[catalinosonesti]

What year is the car
HI
It was 2011 .... with 9S12XHZ512....

[comnic5]

Hello guys.
I have an CarProg 7.28 wich i lost the A1 adapter. With this one I was able a few years ago to read PIN by obd2 from an Opel Zafira PSG16.
Now I need to read PIN from my PSG16 Vectra C.
So the story is that not having the A1 adapter for the 7.28 version I just bought a new one wich is the 10.93 version.
I was trying to connect to ecu by obd2 with the new one but i get errors like voltage supply less than 8v.
if i try to use the new a1 adapter with the old version it just fail to connect to ecu.
Any ideas of what should i do? Should i provide 12v external to the 10.93 version?
Pls help

[PACEVE]

hmm
china country of unlimited possibilities
CARPROG FULL (with all Software's activated and all 21 items Adapters) NEW

CARPROG FULL V4.01

From 75 USD / pcs - 60 Eur

what more to say

:canabis::canabis::canabis::canabis::canabis:


Thanks, I will test it

[frankrayk]

Thanks, I will test it

What are you going to test??? this is from 2012...

[tganley]

hi can any one help i have the chinese carprog but i need this can anyony help thanks 2016 car
With this software you can unlock:


Opel, Vauxhall CD500 UXX made by Blaupunkt;
Opel, Vauxhall NAVI600 UCU made by Bosch;
Opel, Vauxhall NAVI900 UCW made by Bosch;
Opel, Vauxhall DVD800 Navi UXX made by Bosch;
GM, Chevrolet UEW and others audio made by BOSCH or Blaupunkt,

!!! NOT WORK with older Opel radios to year 2007 !!!
!!! NOT WORK with Opel Panasonic units: CD400, CD300, NAVI650, NAVI950 !!!
!!! NOT WORK with Chevy Panasonic units: 23497398 and simmilar !!!
!!! NOT WORK with GM, Cadilac, Chevy Denso units: UYS, UFV !!!

[slevy70]

anyone embraced micronas cpu in Passat 2007 with Carprog clone?

[Marios80]

The number of units ran out on my carprog clone 8.21. I deleted all carprog files and downloaded 8.21 with key gen but every time I try to load cargprog and read an eeprom in tells me it cannot locate correct ".lib" file. I noticed that this ".lib" file is the device s/n but when I load carprog the Device S/N is still matcfhing my old ".lib" which is expired. Is there anyway to fix that so the new downloaded version can recognize the new ".lib" file?

[Domi]

Reflash MCU

[catalinosonesti]

Hi
What is the procedure to read write km and immo for a new key , in vw polo 2013 model , i have carprog v 13.80 original ?
Can i try to do by OBD A1 Multi ?
Best regrads

[tango]

Hi
What is the procedure to read write km and immo for a new key , in vw polo 2013 model , i have carprog v 13.80 original ?
Can i try to do by OBD A1 Multi ?
Best regrads

if you have original then maybe best to ask this on their forum you will get a quicker answer because they should know

[catalinosonesti]

Hi
Thank you for fast answer , polo dash is 6R , and i think is NEC procesor and 95320 ,
What is the steps to write km and read immo for the 3 key .
Thank you

[linn123]

现在CARPROG中国价格290RMB（大约40USD）

[biglake84]

can carprog read the bosch motronic me7.6.1 ECU?

[Unichip77]

Hi,

can I have connection diagram for Airbag Citroen C4 9678691580?

Thak you
Uni