Mercedes clk 430 problem

[alfons37]

Mercedes clk (208) 430 2000
Engine code m113.943 205kw
Ecu box a0265456932 hw39.97
Bosch 0261206303

I work with Mercedes clk 430 and my problem is i not have ecu box, but I have buy used ecu (Bosch 0261206303). If I understand is right so I must married this box with car. I have star Mercedes. What is best solution for this? Immo off I think or use star for married this box?

Thanks:proud:

[alfons37]

Vin number WDB2084701T047903

[vanos batam]

HC11 inside ECU..read it

[alfons37]

I cant find HC11 component, only i can see for flash eeprom is ab28f200.

[kaToo]

what is this ... ?

[alfons37]

It is ecu for MB clk 430 :)

[smayer]

Read MCU, virginize and maried with Star.

[alfons37]

Ok good but have you designation on component or you can tell me on picture where i can find mcu

[alfons37]

Now i understand :) i come back later with dump

Thanks

[alfons37]

I have problem with read out file, i have one file but i think is wrong.

[alfons37]

Here is file

[vanos batam]

Here is file

Here is file

[alfons37]

Thanks for file.

Have i read out file right? I choose mc68hc11e9 (w/security 0f36w) in prog programmer and it , it is file i attachment. On my motorola chip is it mask 4e28b.
I try on mask 4e28b but my xprog say (device is silent)

[smayer]

Thanks for file.

Have i read out file right? I choose mc68hc11e9 (w/security 0f36w) in prog programmer and it , it is file i attachment. On my motorola chip is it mask 4e28b.
I try on mask 4e28b but my xprog say (device is silent)

If you read in circuito must cut 1 pin. Is pin 20, connected to B3 in xprog.

[alfons37]

I read with plcc52 adapter.

[alfons37]

Now i install mb super star 4 , i have test v30 on car and it work with diagnos. Byt when i try with mb star so is it message communication error. i use hl-340 usb converter and set it to com port 1, it is right?

[smayer]

Now i install mb super star 4 , i have test v30 on car and it work with diagnos. Byt when i try with mb star so is it message communication error. i use hl-340 usb converter and set it to com port 1, it is right?

Set com 2.

[alfons37]

My error code is (1.2)-2.503.9551
Maybe is my star is destroyed, i never use this product, i have it 1/2 year but not test. I have test com 2, i use vmware , maybe is is wrong

[alfons37]

Here is exact message

DAS XENTRY CAL 503 ERROR FAULT (1.2)2.503 13003-9551 FIX (http://www.x431.us/product.php?id_product=448)

[alfons37]

No w work super mb star. Shall i take control module adaptions in xentry, or shall i work in das?

[alfons37]

after this say

1 version coding
2 correction program
3 self adaption

What shall i use for married box?

[benzstop]

use version coding option then learn drive authorization

[benzstop]

dont forget to put in coding number first,coding number get from epc

[alfons37]

Is it scn code i need from esp, i am beginner on mb cars :)

Thanks

[alfons37]

i order new latest mb SD Connect Compact 4 New Star Diagnosis C4 , hope this work better, for my old super mb star have connection problem,

[alfons37]

i order mb SD Connect Compact 4 New Star Diagnosis C4 but no success :(

I can connect car all without engine

[alfons37]

Can i do immo off for this car?

[alfons37]

Now work diagnos :) and i have program
hc11_org.bin_renew.rar (165 Bytes, 9 views)


But i not understand how i coding.

This picture have 4 choice

I take number one but ask after code, where can i found code?

[smayer]

Now work diagnos :) and i have program
hc11_org.bin_renew.rar (165 Bytes, 9 views)


But i not understand how i coding.

This picture have 4 choice

I take number one but ask after code, where can i found code?

You found the code in EPC, If need. help post the VIN.

[alfons37]

Here is vin number

Vin number WDB2084701T047903


Thanks

[smayer]

Here is vin number

Vin number WDB2084701T047903


Thanks

Code 137005013

FTP ABGASZYKL 137045013

918-----137025013

Kat 625----137145013

[alfons37]

Many thanks for code, now car start :)

When i coding xentry say at i can only start 50 times?

And i cant drive with car it is not respons from pedal it is only 800 rpm, when i press on pedal nothing happening so i think i must do self learning, i do this but i got strange message

[alfons37]

Car going very bad, it drinking to much gas so i cant start more. Maybe is throttle error , think adaption, for i cant calibrate throttle house. It give error message when i try adaption throttle house.

My codes for engine is p1542,p0720,p0335,p1605, if i erase code so come back p1542 and p1605.

My box number is a0265456932 maybe is wrong box for this car?

Thanks

[benzstop]

maybe ecu faulty,check actual values for throttle actuator

[alfons37]

yes you're right, I have ordered a second hand ecu with the correct box number, the second ecu was not correct box number for the chassis number. And old ecu maybe broken.

[alfons37]

Now work car , thanks for all help :)

But i have littl eproblem with error code

p1605
p0600

It have with esp, in instrument display message " esp defekt"

Must i recode esp to car, for i have change esp to a used, my esp orginal is gone, so i buy used esp...

[alfons37]

Now i solution old codes, but have new codes c1022, c1303
And my cluster display say el stab program and brakeassistant

Anyone have ide?

[Punchi]

Is.your esp ecu the same number as the old one?

[alfons37]

No it is not same number but it shall work to clk430

[alfons37]

I attachment picture on ESP

My orginal number "ESP" for this car is A0295457232

My chassi number is WDB2084701T047903

[smayer]

I attachment picture on ESP

My orginal number "ESP" for this car is A0295457232

My chassi number is WDB2084701T047903

Check CAN plug pins, sometimes 1pin Go to inside of ESP unit.

[alfons37]

You mean i check pin 1 on esp, if is broken?

Thanks

[alfons37]

Smayer can i use this esp box number to this car?

A0255456132

[smayer]

You mean i check pin 1 on esp, if is broken?

Thanks

I mean you must check the two Pins from CAN plug.

[alfons37]

Ok i understand, first when i recode engine ecu with scn code , all work good, but after job i can see at i missing can plug to esp box, 2 cables green/white, i hade error code p1605,p0600,

I plug can contact to esp, and p1605,p0600, is gone, after this so i have this code c1022,c1303

Must i have this can plug in esp box when i use scn coding for engine ecu?

[foxdata]

Code 137005013

FTP ABGASZYKL 137045013

918-----137025013

Kat 625----137145013

hi mate
my vin is WDB2100821X004557
pls can you calculate the the code for me to sync ecu to eis

[smayer]

hi mate
my vin is WDB2100821X004557
pls can you calculate the the code for me to sync ecu to eis


002 008 008 whiteout Kat
002 048 008 whit Kat

[hass42]

I have similar problem, xprog device 4e28b device silent only can read and write with e9 w/security of36w??

I have no communication with ecu using C4??
PLease help heres my original file and my vin # is WDBNG75J0YA129985
Thanks I would much appricate help

[smayer]

If you don't have communication with ECU first check GND and +12 in ECU plugs, also check diag line.

[hass42]

I have already checked all of my gounds power and data lines to and from all ECU's
Sent from my DROID RAZR HD

[benzgeek]

Mr. Duck keep asking Questions and our mates keep working hard and awnser him with them golden awnsers but ... Mr Duck never Click thanks to them ... he just say " Thanks "clicking tanks is much powerfull for our mates Mr duck !!

Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks


Merry christmas and happy new year all DK Members

[smayer]

Mr. Duck keep asking Questions and our mates keep working hard and awnser him with them golden awnsers but ... Mr Duck never Click thanks to them ... he just say " Thanks "clicking tanks is much powerfull for our mates Mr duck !!

Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks
Thanks


Merry christmas and happy new year all DK Members

Amazing this post from you, I can see you have used the Thanks button once, it's just for test purposes?
merry Christmas.

[hass42]

LoL...... Very well put you should be always appreciated for this site and its members it will be very tough to teach yourself what would we all teach each other collectively
Merry Christmas to all
Sent from my DROID RAZR HD

[philt]

Hello,

New to DK so please be gentle.....................
I have a Merc E430 engine with harness + ECU which I want to use in a project car. I would like to retain the original ECU rather than fitting an aftermarket item BUT I do not have key etc for immobiliser. Is it possible to de-activate the immobiliser, and would the engine run ok on a manual gearbox? I am not worried about fault codes etc, just want the engine to run normally (not in limp home mode).

Many thanks,
Phil.

[hass42]

http://www.youtube.com/watch?v=qYhNcl7JfsQ&feature=youtube_gdata_player

Check this out for your engine install philt

[Artjom]

Hallo,

can someone help me to change FIN nb

org: 2102701A851517

need : 2083701F059079

thx

[wsc]

Hallo,

can someone help me to change FIN nb

org: 2102701A851517

need : 2083701F059079

thx

here mate , maybe a litle late .....:)