Digiprog 3 clone questions and answers

[zecamaneca70]

Regen with star or autocom always work fine.


I Used Star, Light went OFF but still 125%, i have made reset to ashes for 0,0% and still shows 125% (when car starting) and DPF was in good condition (was 45%). Do you know if this conected with the fact that ezs is changed for 1.6 ?

Did it hapens also a lot to You?

Thanks

[rtbdiagnostic]

:)
Cool need some advice what adapter to use then on a 2009 ford bantam cluster with NEC micro maybe an pdf diagram to assist do you use ST51 perhaps :)
check this one out seems to work on the ford bantam dash using ST29 adapter332830:mask:

[rhg84]

Won't work, the mileage is stored in a different spot on a Civic and other Accord chips. Use the EEPROM menu, set type as 93C76, read the file, save it, then change manually and write it back.


Thanks got the file saved to my digiprog. Is there a resource with the location of the mileage for different cars or is a trial and error kind of thing? I'm in the US it will still show kilometers and have to type it in as so correct?

[clusters]

Thanks got the file saved to my digiprog. Is there a resource with the location of the mileage for different cars or is a trial and error kind of thing? I'm in the US it will still show kilometers and have to type it in as so correct?


Best to start a new thread for help with this.

[matekhr]

Hello,
Eeprom function on my Digiprog doesn't work.
In fact, I can read/write only 24cXX eeprom without problems, but all other eeproms give an error.
I tested some 95XXX, 93cXX and 35080V6, all of them fails :(
I use an adapter (which needed a little repair to make it work), not attached clip (which is really a garbage), and eeproms are from my home "collection", some new, some used, but all in good working condition. My other programmers don't have any problems with them.
Have you any idea what should I check/repair to make an eeprom function work?
Thanks in advance.

[Meat-Head]

otvori digi i prelemi cijelu plocu...

Ingkush, EMERUCAN or oztrailan only dude

[javyb]

English please

[salkapone]

learn the croatian language,,,, I learned english so it would be fair that you learn croatian,,, :):), I only wrote that review board to find a bad solders on digi wigi

[Johnner]

Salkapone,I would advise you to have a look at item #29 in this list...

Forum Rules (http://www.digital-kaos.co.uk/forums/showthread.php/2-Forum-Rules)


Thank you...

[javyb]

learn the croatian language,,,, I learned english so it would be fair that you learn croatian,,, :):), I only wrote that review board to find a bad solders on digi wigi
This is an English speaking forum so I don't want to or need to learn croatian. Find a croatian forum

[Johnner]

It's okay......let's move on from this... everybody is now calmed down....

[matekhr]

I only wrote that review board to find a bad solders on digi wigi

I already did that but nothing changes :(
I need a more specific hint.

[FORKAD]

Hello all team
i have digiprog V4.94 clone
please i can work Digiprog by obd BMW CAS3
Is bmw 118D year 2012

fOR INFO/
Eeprom function on my Digiprog work Perfect
I read/write 24cXX 95XXX 93CXX eeprom without problems
I read 35080V6 ok, For write in NEW cHIPS 35080 is perfect

[javyb]

Hello all team
i have digiprog V4.94 clone
please i can work Digiprog by obd BMW CAS3
Is bmw 118D year 2012

fOR INFO/
Eeprom function on my Digiprog work Perfect
I read/write 24cXX 95XXX 93CXX eeprom without problems
I read 35080V6 ok, For write in NEW cHIPS 35080 is perfect
No you cant

[FORKAD]

Please wiht cable CAS-DIAG is working

[garabounga]

Use rosfar red clone its better cas cable wil damage your cas

[matekhr]

Hello,
Eeprom function on my Digiprog doesn't work.
In fact, I can read/write only 24cXX eeprom without problems, but all other eeproms give an error.
I tested some 95XXX, 93cXX and 35080V6, all of them fails :(
I use an adapter (which needed a little repair to make it work), not attached clip (which is really a garbage), and eeproms are from my home "collection", some new, some used, but all in good working condition. My other programmers don't have any problems with them.
Have you any idea what should I check/repair to make an eeprom function work?
Thanks in advance.

Still need some repair ideas...

[FORKAD]

you read wiht adapter?

[matekhr]

Yes, I read with the attached adapter. It needs a minor repair, pin 19 on the 25-pin connector wasn't connected to pin 5 on the eeprom side, so I made the missing connection (solder a piece of wire). Now I can read/write all 24cXX eeproms, but all others fail.
I don't know how digiprog makes internal pinout switching while you choose the eeprom type trough the menu. I tested only the voltage pins, and this part seems to be OK (for instance, I2C and SPI eeproms have Vss on pin 4, 93cXX has Vss on pin 5, and M35080 on pin 1, and Vcc is on pin 8 for all eeproms.) I can hear a relay clicking when trying to read an eeprom, but have no idea whether one or more relays is/are to click, depending on the eeprom type... any help is greatly appreciated

[aem]

hi friends i try to connect digi to eetool.iinstall driver on com 7.then start eetool and set com 7 but give me error ''gerat nicht gefunden''

i do set pc term on digiwigi and it have ftdi inside.....

thanks

[teerak2uk]

hi friends i try to connect digi to eetool.iinstall driver on com 7.then start eetool and set com 7 but give me error ''gerat nicht gefunden''

i do set pc term on digiwigi and it have ftdi inside.....

thanks
Change port to com 1 or 2 in device manager and try again or try this version

https://www.dropbox.com/sh/a41rfvg9hkk2cji/AACEi4C9fmN_fxTrOQpmox7Aa?dl=0

[digi men]

When you give Pc Term on digi, dont do nothing more on digi then try(dont pres ok)

[aem]

When you give Pc Term on digi, dont do nothing more on digi then try(dont pres ok)

thanks.....this is the procedure.thanks again!!!!

[hani key]

volvo s80 2008 is it can be done with it

many thx

[garabounga]

hallo guys

is there any news about digiprog 4 cloning?

[javyb]

hallo guys

is there any news about digiprog 4 cloning?
Yes there's 100 clones being tested

[garabounga]

ok nice news whos testing and when wil we get the results ?

[javyb]

ok nice news whos testing and when wil we get the results ?
Repsoft is testing

[garabounga]

hhhhhhh i specified clones i guess if they are testing it wil be long before we can have something thanks any way for your answer

[javyb]

hhhhhhh i specified clones i guess if they are testing it wil be long before we can have something thanks any way for your answer
I was joking. Digiprog 4 not been released yet. I doubt they will get cloned again

[garabounga]

im afraid that our chines friends can clone any thing, they even recently cloned a ~~~~ing range rover EVOQUE.

[javyb]

im afraid that our chines friends can clone any thing, they even recently cloned a ~~~~ing range rover EVOQUE.
Yes they can clone anything but they only clone what's worthwhile in terms of selling. They not cloned enigma yet or diagprog 3 although they advertised they had diagprog 3 but it never came to life

[aem]

Digiwigi skoda superb 2011 nec+24c64 obd works fine. "Good chinese food " :))

[paul_12345]

Repsoft is testing

and who is going to trust a company that put the digiprog3 on 'sale' to clear there stock and release a couple of updates around that time to make people think there would be more updates.

[Faraday]

digi killed ford maverick hc11 today :(

[hani key]

http://images.tapatalk-cdn.com/15/09/30/e02f83fae56f76a505dbf0c2bceff02e.jpghttp://images.tapatalk-cdn.com/15/09/30/cc5a6c24c45ff56b967fa969de02e79b.jpg

VOLVO S8P DONE ALL OK

Sent from my LG-D855 using Tapatalk

[hani key]

All ok by obd2 it ia take 10 minutes and all ok 😉😉

Sent from my LG-D855 using Tapatalk

[javyb]

All ok by obd2 it ia take 10 minutes and all ok 😉😉

Sent from my LG-D855 using Tapatalk
Read dtc with scanner you will see a mileage tampered fault code that can't be erased

[hani key]

Also digi prog kill vw toureg 2012 dash ~~~~ i read 95320 need fix also this photo of it before damaged 😞 http://images.tapatalk-cdn.com/15/10/01/2d81cdd1cc516c5162ccd53b9e45494a.jpg

Sent from my LG-D855 using Tapatalk

[aem]

you digiwigi is yanhua?

[Dayo]

Use xtool


Sent from my iPhone using Tapatalk

[teerak2uk]

Also digi prog kill vw toureg 2012 dash ~~~~ i read 95320 need fix also this photo of it before damaged 😞 http://images.tapatalk-cdn.com/15/10/01/2d81cdd1cc516c5162ccd53b9e45494a.jpg

Sent from my LG-D855 using Tapatalk
Use the backup you made from 95320!!!!

[aem]

that's why i ask him if is yanhua

[hani key]

Original dump lost 😐😐

Sent from my LG-D855 using Tapatalk

[javyb]

that's why i ask him if is yanhua
Yahuna or not digi cannot do the new a6

[javyb]

Original dump lost 😐😐

Sent from my LG-D855 using Tapatalk
Time to buy a new dash

[hani key]

Do u have mew dash same it !!

Sent from my LG-D855 using Tapatalk

[hani key]

Dash 7P69209880A

Sent from my LG-D855 using Tapatalk

[javyb]

Dash 7P69209880A

Sent from my LG-D855 using Tapatalk
A dump from same dash wont work.

[FORKAD]

Look in ebay uk or ebay de to find one
but to learning new key and coding new vin

[hani key]

I know same proplem i see it is show me safe and same - -

Sent from my LG-D855 using Tapatalk

[arvedo]

friends question do jaeger Renault Megane 2000 by gray connector can help

[gjuzel]

licznik 4.7can help!

Sent from my GT-I9305 using Tapatalk

[teerak2uk]

friends question do jaeger Renault Megane 2000 by gray connector can help
I think carprog does some versions

[arvedo]

dp3 clon
You can do for connector ??
is that I had read that you could with other connector

[matekhr]

Can you tell me which diode is D19 (near the power plug)?
Mine looks pretty burned...

[FORKAD]

Please digiprog v4.94 i can work by obd fiat ducato 2012?

[bersch8688]

Yes Fiat Ducato 2012 work perfect OBD

[bersch8688]

Digiprog 4.94

Fiat Doblo 2009 ---> OBD Work perfect 1 sec. Job

[kaihoc]

I want one ST59 as well.

[Dayo]

Is a 2015 64 plate xtrail possiblr with digi? I cant find any posts, im hoping its wire on with st47 like the one before?

Thanks


Sent from my iPhone using Tapatalk

[javyb]

Is a 2015 64 plate xtrail possiblr with digi? I cant find any posts, im hoping its wire on with st47 like the one before?

Thanks


Sent from my iPhone using Tapatalk
No it won't work

[Dayo]

How can they be done


Sent from my iPhone using Tapatalk

[javyb]

How can they be done


Sent from my iPhone using Tapatalk
Obd with a good tool

[Dayo]

Xtool?


Sent from my iPhone using Tapatalk

[DashProg]

Did digiprog can do range rover evoque 2013 via obd

Sent from my ASUS using Tapatalk

[javyb]

Xtool?


Sent from my iPhone using Tapatalk
I said good tool not bad [emoji23] . It's obd with smelecom.

[teerak2uk]

Did digiprog can do range rover evoque 2013 via obd

Sent from my ASUS using Tapatalk
Someone reported it working but I wouldn't risk it

[DashProg]

Someone reported it working but I wouldn't risk it
I try to read it tacho via obd first said plug 16 after confirm ok said 93c76 plug 1

[teerak2uk]

Should be 2 options
St16 or st1/4 basically clip

Or purchase smok and after 2 cars your in profit

[aem]

somebody use or try digiwigi Y on vag cluster with nec inside and 2 procedures on digi manuel? ''remove dash solder st47....put back dash and make it via obd''

[Dayo]

I said good tool not bad [emoji23] . It's obd with smelecom.

2015 xtrail does work with digiprog 4.94, chip 93c86 ;) worked a treat :)


Sent from my iPhone using Tapatalk

[Dayo]

I try to read it tacho via obd first said plug 16 after confirm ok said 93c76 plug 1

I wouldnt risk them with digi. Get xtool or smok for them. Evogue and touregs are abit dangerous with digi ;)


Sent from my iPhone using Tapatalk

[aem]

some people here wanna sell their products and we have to understand them.

[Dayo]

some people here wanna sell their products and we have to understand them.

Haha. You cant knock digi clone for what it can do. Very good value for money. Obviously enigma,dp3 and smelecom are 3 of the best, but they have a hefty price tag. Going to have to bite the bullet one day!


Sent from my iPhone using Tapatalk

[javyb]

Haha. You cant knock digi clone for what it can do. Very good value for money. Obviously enigma,dp3 and smelecom are 3 of the best, but they have a hefty price tag. Going to have to bite the bullet one day!


Sent from my iPhone using Tapatalk
If you charge good money the hefty price tag shouldn't bother you. if your doing cars for ?30 then u buggered

[Dayo]

Very true mate. Which would you say is the better of the 3?


Sent from my iPhone using Tapatalk

[javyb]

Very true mate. Which would you say is the better of the 3?


Sent from my iPhone using Tapatalk
Depends on budget. Elprosys ahead in terms of updates but support can be crap. Smelecom good but slow on European updates.

[u.s]

2012 Ford Focus - 95320 - by ST1 work ok

[unucip]

Astra J 2011 work by OBD.

[winaiservice]

Today I do volvo s80 2008+ work good 10min.

[djoko.k]

Having trouble with can based cars ``no connection``... Any experience?

[Dayo]

Check obd cable connections in st16


Sent from my iPhone using Tapatalk

[djoko.k]

Cabel checked connector resoldered....

[aem]

can anybody confirm zafira 2011 by obd?

[teerak2uk]

can anybody confirm zafira 2011 by obd?
Yes it will .

[Dayo]

Zafira c yea


Sent from my iPhone using Tapatalk

[aem]

Somebody make golf 4? I try to make and stay 40 min on verify 5 and read and read and nothing .....

[I Vasil]

Motometr dash about 60 min .

[Dayo]

Iv only ever struggled with a year 2000, took ages to go through


Sent from my iPhone using Tapatalk

[garabounga]

Golf 4 MM Just open dash en look voor 24C** it takes 2 minutes

[viejomatius]

335864


Hello exist a method to make these old megane dash, in this easy way with Digiprog 3 clone???? like old tacho 2008

[Speedofix]

Audi Q7 2013 someone try them ?

[garabounga]

335864


Hello exist a method to make these old megane dash, in this easy way with Digiprog 3 clone???? like old tacho 2008

This method dont even work with tachopro en you want to make work with digi???!!!! nice :)
im afraid not .if you succeed let us know please

[viejomatius]

Thanks for reply, but with tach? pro 2008 works 100% fine, tested hundreds of times, but no succes with digiprog

[garabounga]

Ah ok then excuse me because i tried with mine never succeeded i think bad unit maybe you are wright if tacho can read it this way why not with digi look to the schematic of tacho and try to make sence with pinouts i once tryed with tacho nec to read a Elantra nec with the schematic cluster pinout of een enigma but it didnt work but its not a bad idea at all i wil look once again to the schematic maybe !!!! but digi wil barbecue the hc908 for sure if it with solder points

[skens]

hi
passat 2011 work by OBD
regards

[memet99600]

hi guys
I'm new in this forum but I want to share my experience with my digi clone. I buy this model http://fr.aliexpress.com/item/DHL-Free-shipping-2013-Digiprog-III-Odometer-Programmer-with-Full-cable-the-Newest-Release-Digiprog-3/679100704.html?adminSeq=201002923&shopNumber=909653 but it's a bad clone did not work with all car I try and now I have a device and can't use it. I try to do bmw and passat nothing working correctly. The most strange in this product is can read mileage without any cable conected for bmw 3series and 307. Now I want to know if you have some link for a model who work perfectly or if a person know how repair the main unit i'm very disapointed. I can share picture of motherboard if you want.
Thank you guys.

[teerak2uk]

hi guys
I'm new in this forum but I want to share my experience with my digi clone. I buy this model http://fr.aliexpress.com/item/DHL-Free-shipping-2013-Digiprog-III-Odometer-Programmer-with-Full-cable-the-Newest-Release-Digiprog-3/679100704.html?adminSeq=201002923&shopNumber=909653 but it's a bad clone did not work with all car I try and now I have a device and can't use it. I try to do bmw and passat nothing working correctly. The most strange in this product is can read mileage without any cable conected for bmw 3series and 307. Now I want to know if you have some link for a model who work perfectly or if a person know how repair the main unit i'm very disapointed. I can share picture of motherboard if you want.
Thank you guys.
How have you tried obd or clip

[Berubeg]

Vw Jetta 2013 take golf 6 on car list. Work fine 2 minutes

[unucip]

passat 2006 dash work
edc16 unknown version
some edc 16 does not work with my 4.94 digi
someone knows a tool for edc 16 for km, immo....?

[sida]

passat 2006 dash work
edc16 unknown version
some edc 16 does not work with my 4.94 digi
someone knows a tool for edc 16 for km, immo....?

For EDC16 I am using VAG DASH CAN and never had a issue with it. Digi does not work EDC16 on Passat, Audi A4, tested only on Golf 5 EDC16 it was good...

[sida]

Vw Jetta 2013 take golf 6 on car list. Work fine 2 minutes

2013? I dont know are you brave orjust had a luck :damnmate:

[Berubeg]

Why? You have bad experience with this car and Digiprog?

[Berubeg]

This is my cluster model. You not thrust Digiprog on this model Sida?

[rtbdiagnostic]

336640336641336642
Is anybody try to do hilux 2011?
Use the pdf's attached Hilux 2006 earlier models use 93c56 in menu landcruiser c56 to read and write for later models use 93c66 which is in digiprog menu hilux c66 although it says use ST 01 you use as per pdf and colour chart ST47 to read & write eeprom in circuit - no need to strip cluster or remove needles ...:y:

[memet99600]

How have you tried obd or clip

I try with OBD but when I remove dash from an other car for try with ST01 it said chip not found I try for a bmw e90 eeprom clip, maybe it's my clip is bad ?? I have to check my clip, I see in this forum a person who done a passat 2006 by OBD in 1min but maybe it's my fault I don't know

[Dayo]

Unsolder the chip and try


Sent from my iPhone using Tapatalk

[memet99600]

Unsolder the chip and try

Ok I try it thanks

[ibratex]

Hello mates on digiprog 3 version 4.94 till now

Made : sportage 2012
Swift 2014
Ranger 2010
Prado 2006
Runner 2006
Navarra 2012


All eeprom on board ...i did NOT try obd

[Berubeg]

When st01 is clip on the chip Check with a little tool If the steel tab touch the leg of the chip. If the leg spring bend the st01

[teerak2uk]

I try with OBD but when I remove dash from an other car for try with ST01 it said chip not found I try for a bmw e90 eeprom clip, maybe it's my clip is bad ?? I have to check my clip, I see in this forum a person who done a passat 2006 by OBD in 1min but maybe it's my fault I don't know
Clip and obd cables are known to be poor quality

Change DB9 plug on st16

[unucip]

only VDO work...

[aem]

vito mm dash 95080 with solder pin on back of pcb and st47 work ok/read real value/ write ok

[Berubeg]

My friend have salvage Yard and go this morning to make test. The r?sult is:
nitro 2009:ok
patriot 2013:ok
caliber: not work
tribute 2008 and 2009: not work
caravan 2012: not work
focus 2012: not work
golf 2007: dash and dsg ok
300 m 2009:ok
cruze 2014:not work
focus 2013:not work
jetta 2014: ok test Many Time always ok
tiguan 2009: ok test Many Time always ok
wrangler 2012:ok
q7 2011: read but very long to write i stop test because no more Time...

[skens]

hi
evoque 2012 work by OBD
regards

[FORKAD]

please where i can buy
transitor Q23 Q26 ?
for solved problem NO COMINICATION
Thanks for help

[clusters]

Nissans

2002 Altima 93C66 OK in circuit with Murano
2001 Xterra 93c56 OK unsolder with Patrol

[garabounga]

Focus 2012 blue screen via clip just flip the display over to get acces to eeprom i did one las week

[Dayo]

Focus 2012 blue screen via clip just flip the display over to get acces to eeprom i did one las week

95320 ;)


Sent from my iPhone using Tapatalk

[garabounga]

95320 ;)


Sent from my iPhone using Tapatalk


Thanks Dayo for the detaild info :)

[bersch8688]

Digiprog 4.94

Toyota RAV 4 2007 ---> eeprom clip 93c56 work

[skens]

hi
MERCEDES w210 E - DB 4_99 with Stecker 10 , ok!
regards

[electronicservicemate]

audi a4 2010 obd ok, audi a3 2010 obd ok

[sida]

audi a4 2010 obd ok, audi a3 2010 obd ok


One question? Did you have any problem with doing A3 dash? Thanks

[Berubeg]

Someone try jeep compass 2014?

[electronicservicemate]

no problem with audi a3 for now 2011 and 2010 doing ok by obd

[satkingno]

I am trying to correct Berlingo 2002 dash. HC08. Is that possible with DP3 clone?

[xtech]

Hc08 not working

[teerak2uk]

Hc08 not working
Works with right modifications

[satkingno]

Really? What modifications would that be teerak2uk?

[viliukas]

Hi friends, i tried change mileage on mercedes w211, 2007 years (facelift), i choose on digiprog mercedes-w211-tacho diag-plug 16(60)-ok and in the right corner it write that - connection500 - verify 83 and it stopped to work and i got ''ERROR NO COMUNNICATION''. I tried a few times but all the time i got the same...The dash is VDO. With car everything ok - i tried connect with autocom diagnostic tool to dash and other blocks - everything works fine. Where could be a problem? Digiprog 4.94, can works fine on that device(i did a lot can bus VAG cars...). Thanks for your help.

[bodzio012]

Try engine running

[viliukas]

Try engine running
The car was standing about a month, i think starter motor cranked a little bit too slow because battery wasn't fully charged. You think low voltage could be a problem when digiprog try to read the dash?

[Dayo]

Jump start the car. Run for 2 miles. Turn car off. Ignition on and it should work


Sent from my iPhone using Tapatalk

[javyb]

Hi friends, i tried change mileage on mercedes w211, 2007 years (facelift), i choose on digiprog mercedes-w211-tacho diag-plug 16(60)-ok and in the right corner it write that - connection500 - verify 83 and it stopped to work and i got ''ERROR NO COMUNNICATION''. I tried a few times but all the time i got the same...The dash is VDO. With car everything ok - i tried connect with autocom diagnostic tool to dash and other blocks - everything works fine. Where could be a problem? Digiprog 4.94, can works fine on that device(i did a lot can bus VAG cars...). Thanks for your help.
Take dash out and use st60

[viliukas]

Take dash out and use st60
i could try, but the problem is that i have not a full digiprog ( without cable set). Maybe someone could help me with st60 cable pinout? It was a problem for you with this w211 that it couldn't be done throuhgt OBD and helped jus st60 cable for you? I have a friend who has digiprog 4.94 and done this model through OBD over 10 cars...thanks.

[teerak2uk]

i could try, but the problem is that i have not a full digiprog ( without cable set). Maybe someone could help me with st60 cable pinout? It was a problem for you with this w211 that it couldn't be done throuhgt OBD and helped jus st60 cable for you? I have a friend who has digiprog 4.94 and done this model through OBD over 10 cars...thanks.
ST 60

~

~db25 ~ dash
~~

~13 ~~~ ~1 ~GND

~12 ~~~~ 4+6 ~POWER

~9 ~~~~~ 17 ~CAN

~10 ~~~~ 18 ~CAN

[viliukas]

ST 60

~

~db25 ~ dash
~~

~13 ~~~ ~1 ~GND

~12 ~~~~ 4+6 ~POWER

~9 ~~~~~ 17 ~CAN

~10 ~~~~ 18 ~CAN
Thanks mate ;) I'll do this cable and i'll try to do this dash on the table. I have the last question: when i'll do this dash through OBD or on the bench digiprog should show me the old mileage value? Or it will be ''the old value: ?''. thanks.

[memet99600]

Unsolder the chip and try

Hello I try to unsold chip but read wrong mileage and when I push "X" it says unknow version, my digi not work ?337907337908337909

[aem]

are you sure you put pin 1 where it have to be?

[teerak2uk]

Chip looks rotated but could just be poor picture

[aem]

anyway that 35080 can not be write with digi.....only if is new 35080

[PremierD]

:hmmmm: ......... 35080 in a Merc e class mate ... you need to leave of the weed :)

[javyb]

:hmmmm: ......... 35080 in a Merc e class mate ... you need to leave of the weed :)
There on about a astra h Tam [emoji23]

[Dayo]

Hello I try to unsold chip but read wrong mileage and when I push "X" it says unknow version, my digi not work ?337907337908337909

Havent you got st01 clip?


Sent from my iPhone using Tapatalk

[memet99600]

have, try and same result :(

[viliukas]

Hi friends, i tried change mileage on mercedes w211, 2007 years (facelift), i choose on digiprog mercedes-w211-tacho diag-plug 16(60)-ok and in the right corner it write that - connection500 - verify 83 and it stopped to work and i got ''ERROR NO COMUNNICATION''. I tried a few times but all the time i got the same...The dash is VDO. With car everything ok - i tried connect with autocom diagnostic tool to dash and other blocks - everything works fine. Where could be a problem? Digiprog 4.94, can works fine on that device(i did a lot can bus VAG cars...). Thanks for your help.
UPDATE:
Today i tried as you said with engine running throuhg OBD, tried drive few miles, tried take dash out and do it with st60 on the table but i have the same result...Any ideas? Problem with digiprog?I tried switch it with power supply adapter on the table, choose w211-tacho diag(power supplied just main unit without any cables) and i have the same result as it would be connected in OBD port or with st60 cable - connection-verify500-verify83 and i got ''ERROR NO CONNECTION''. I could guess that my digiprog CAN line don't work, but i tested it on audi a4 2006 and skoda superb 2008 and everything works fine...Any ideas? Thanks.

[Dayo]

Check st60 wire up


Sent from my iPhone using Tapatalk

[viliukas]

Check st60 wire up


Sent from my iPhone using Tapatalk

wire up - OK.

[kospoz]

can somebody send me in pm a good seller I want to buy one unit

[garabounga]

UPDATE:
Today i tried as you said with engine running throuhg OBD, tried drive few miles, tried take dash out and do it with st60 on the table but i have the same result...Any ideas? Problem with digiprog?I tried switch it with power supply adapter on the table, choose w211-tacho diag(power supplied just main unit without any cables) and i have the same result as it would be connected in OBD port or with st60 cable - connection-verify500-verify83 and i got ''ERROR NO CONNECTION''. I could guess that my digiprog CAN line don't work, but i tested it on audi a4 2006 and skoda superb 2008 and everything works fine...Any ideas? Thanks.

open the dash en do the eeprom directly

[viliukas]

open the dash en do the eeprom directly
but in this case i should do and ezs if i do dash with programmer on the table via chip...if i do via chip i need dump modification that there wouldn't be sinchronization between ezs and dash (dash wouldn't take mileage from ezs)...

[teerak2uk]

can somebody send me in pm a good seller I want to buy one unit
No such thing as good seller always a gamble when buying from china just check sellers ratings on aliexpress you might be lucky

[aln1]

344 pages of info and I can't find what I'm looking for :apologetic:

My question is simple, can I use digiprog 3 to set kilometers for mercedes SLK R171 for both odometer and EZS?
With so many sellers on alibaba can someone who bought a unit recently recommend one?

Thank you all

[DashProg]

344 pages of info and I can't find what I'm looking for :apologetic:

My question is simple, can I use digiprog 3 to set kilometers for mercedes SLK R171 for both odometer and EZS?
With so many sellers on alibaba can someone who bought a unit recently recommend one?

Thank you all

First go here http://www.digital-kaos.co.uk/forums/forumdisplay.php/2-Introduce-Yourself
Second don't forget to read
Forum Rules (http://www.digital-kaos.co.uk/forums/misc.php?do=showrules)

[DashProg]

344 pages of info and I can't find what I'm looking for :apologetic:

My question is simple, can I use digiprog 3 to set kilometers for mercedes SLK R171 for both odometer and EZS?
With so many sellers on alibaba can someone who bought a unit recently recommend one?

Thank you all

the 344 pages that you claim here is the experience members of this forum and their efforts

you had a bad start :beheaded:

[memet99600]

can somebody send me in pm a good seller I want to buy one unit

I can just say don't buy from zoliobd (from aliexpress) because I buy from this store, they have most good evaluation from other seller and good feedback but my digi not work, if I can help you :(

[garabounga]

but in this case i should do and ezs if i do dash with programmer on the table via chip...if i do via chip i need dump modification that there wouldn't be sinchronization between ezs and dash (dash wouldn't take mileage from ezs)...

for the w211 you can do this ezs with rosfar red clone its strange because this one has to go with obd no offence but did you choose the right menu ? some time we just get confused with another Wxxx in the menu check again and report.

[DashProg]

Mates please
Can digiprog 4.94 do range rover evoque via obd

Sent from my ASUS using Tapatalk

[PremierD]

Yes .. depending on how large your gonads are mate ... :)

[garabounga]

Mates please
Can digiprog 4.94 do range rover evoque via obd

Sent from my ASUS using Tapatalk

Ask DK member Skens he has done it this his replay quote :
hievoque 2012 work by OBD
regards

[norbisko]

digiprog 4.88
2011 Audi Q5, no work.
Tried different menu options, Q7,Q5, waited 40 min kept saying READ 010, 020, 030 .... no go

[XmoDDeR]

norb you around wats going on ??????????????

[aem]

hi friends.i need info about a4 2010.work only on obd or i need to remove eeprom from dash and make 2 steps like on a6 (4g) ?

[PremierD]

PPG mate .............. :) Plug Pray and Go ..........

[aem]

PPG mate .............. :) Plug Pray and Go ..........

:))))))))))))))))))))

[aln1]

the 344 pages that you claim here is the experience members of this forum and their efforts

you had a bad start :beheaded:

No disrespect ment to nobody's effort, just saying that the overwhelming length of this thread makes it impossible to find any useful information that might be hidden in it.
Your reply surly didn't get me closer to the answers I seek.

[memet99600]

anyway that 35080 can not be write with digi.....only if is new 35080

I use the datasheet of the component to find pin 1 :) , can not be write with digi ok I understand but read can not too ? when I use eeprom menu and set 35080 read, nothing happend ...

[Faraday]

I use the datasheet of the component to find pin 1 :) , can not be write with digi ok I understand but read can not too ? when I use eeprom menu and set 35080 read, nothing happend ...

digi read/write 35080 for 100%.

[DashProg]

Range Rover Evoque 2013 via obd ok :congrats:

[memet99600]

digi read/write 35080 for 100%.

Thank you I think the problem is from my main unit, have to buy another :( :( :(

[garabounga]

Om
Range Rover Evoque 2013 via obd ok :congrats:
Ok nice you conform that its ok skens was right thanks for this valueable post

[smokey08]

thanks mate, nice to know :)

now everyone who can google can do evoque too :congrats:

$20 job now :giveup:

[sida]

hi friends.i need info about a4 2010.work only on obd or i need to remove eeprom from dash and make 2 steps like on a6 (4g) ?

I did it only by OBD, it takes about 20 min. Regards

[XmoDDeR]

sharing is caring................this is DK , arent we here to help each other. or is who knows more?

[aem]

Ohohoo. Welcome back gwee!!!!!

[DashProg]

thanks mate, nice to know :)

now everyone who can google can do evoque too :congrats:
The title of this thread is Digiprog clone questions and answers
It's not Gwee's comments

I think you have to be modest is better for you

Ohohoo. Welcome back gwee!!!!!


Sent from my ASUS using Tapatalk

[drpeter]

Range Rover Evoque 2013 via obd ok :congrats: You won the lottery, no damage at all? I don't even think about this doing this job with digi clone.

[garabounga]

welcome back GEWEE

[Johnner]

sorry sir, i don't know how i offended you, please kindly advice :)

you are sounding like a moderator, next in line?? :)

p.s. sorry i forgot you have extremely high reputation, my bad, please forgive me :)






Well mate, I'M a Moderator,and can say that Electrodata is correct.Keep this thread on topic,or it gets binned,and people get upset then.

I would also remind people to have a look at these again : Forum Rules (http://www.digital-kaos.co.uk/forums/showthread.php/2-Forum-Rules)

Pay particular attention to Rules #1,#3 and #31.Anyone flouting these,either blatantly,or skirting around the edges with them,WILL be receiving PM,at the very least...

Carry on.......

And remember,we are a community here,not groups of individual fifedoms...

[mikhailzgv]

Prompt he can make VW Tiguan 2011 ????

[Berubeg]

Yes no problem for tiguan obd2

[sida]

Prompt he can make VW Tiguan 2011 ????

Tiguan 2011 OBD no problem, takes about 10 minutes

[Berubeg]

Digiprog user what you make with Hours and sri on Chrysler Dodge Jeep products? You don't change it?

[XmoDDeR]

Digiprog user what you make with Hours and sri on Chrysler Dodge Jeep products? You don't change it?

another tool , tacho does some early ones, jprog , usaprog , all i know actually that does OBD

[sida]

Digiprog user what you make with Hours and sri on Chrysler Dodge Jeep products? You don't change it?


I guess that digiprog users do not own ONLY digiprog to get a job done.

[teerak2uk]

another tool , tacho does some early ones, jprog , usaprog , all i know actually that does OBD
Yes I brushed off the dust on my TU to do a 2001

[Berubeg]

Sure... For sri is possible with scanner but for Hours If need other programmer not super for a clean job! I'm buy Digiprog for test i have jprog but for most car by obd with Digiprog is not possible to do a clean job...

[rtbdiagnostic]

Either machine faulty, or not VDO dash (TRW/MM).
338717
Would this 2014 VW Polo Vivo dash be done by OBD with Digi Prog ? Looks similar to Magnetti dash or could it be VDO :y:

[Dayo]

Try it. I think that year is nec35xxx


Sent from my iPhone using Tapatalk

[mikhailzgv]

He asks 47 connector. it OBD?

[DashProg]

338717
Would this 2014 VW Polo dash be done by OBD with Digi Prog ? Looks similar to Magnetti dash or could it be VDO :y:
Yesterday I try on Polo 2012 JC Dash with Nec+95320 it gave error

Sent from my ASUS using Tapatalk

[DashProg]

Try it. I think that year is nec35xxx


Sent from my iPhone using Tapatalk
Mate I don't think that the digiprog can do Dash with NEC35xxx

Sent from my ASUS using Tapatalk

[Dayo]

Mate I don't think that the digiprog can do Dash with NEC35xxx

Sent from my ASUS using Tapatalk

I know it cant mate. My digi only does up to and including 2012 with the nec95320


Sent from my iPhone using Tapatalk

[rtbdiagnostic]

338717
works 100% polo 6N 2001 - diagnostic -ST16 - doesn't show old mileage but writes perfect - on cluster display where mileage shows while writing it shows error for about 5sec then check written value on Digi:y:Remember to reset service reminder

[Dayo]

338717
works 100% polo 6N 2001 - diagnostic -ST16 - doesn't show old mileage but writes perfect - on cluster display where mileage shows while writing it shows error for about 5sec then check written value on Digi:y:Remember to reset service reminder

You said 2014, not 2001


Sent from my iPhone using Tapatalk

[rtbdiagnostic]

338869Vehicle is an 2014 Vw Polo Vivo 1.4 Trendline see picture attached but uses same platform as the older model Polo :)

[DashProg]

Polo 2014 have cluster tft color not same picture as you posted

Sent from my ASUS using Tapatalk

[unucip]

My digiprog 4.94 fail today.
Where to buy a good quality one
maybe from europe if somebody knows
thanks

[honingkoning]

My digiprog 4.94 fail today.
Where to buy a good quality one
maybe from europe if somebody knows
thanks

What failure do you have? Blue screen?

Wbr Adam.

[unucip]

"no conection"
few days ago, not all the time
yesterday fail,
checked cable from serial to obd, remove screen to see conector solder but no problem
after remounted touchscreen not work, displaying all but no touch
So, I need screen and I think st16.

[garabounga]

Today i deed the following seat ibiza 2012 no connection
Cas3 bmw with cas connector read write perfect

[honingkoning]

"no conection"
few days ago, not all the time
yesterday fail,
checked cable from serial to obd, remove screen to see conector solder but no problem
after remounted touchscreen not work, displaying all but no touch
So, I need screen and I think st16.

For touchscreen tou resolder all components on pcb.
For st 16 replace serail connector

Wbr Adam.

[mikhailzgv]

Touareg 7P corection??? Can make?

[teerak2uk]

Touareg 7P corection??? Can make?
Year .

[mikhailzgv]

2011 year VW ........

[teerak2uk]

Maybe .

[mikhailzgv]

You tried?

[viliukas]

today i tried audi a6, 2006 years, dashboard - M73 and i get no connection. Any ideas? digiprog 4.94 don't do this dash or i have problem with my digiprog can bus because a few dasy ago i couldn't do and mercedes w211 2007y.(k line works ok). Tommorow i'll test it on passat b6 2006 and i could say if i have connection probems or not because i suspect that my digiprog have can bus problem. Thanks.

[aem]

passat 2011 menu dash diag -2012 read ok/write ok /3 minute.

[Dayo]

Did it have tft?


Sent from my iPhone using Tapatalk

[aem]

no...............................

[mikhailzgv]

Touareg 7P 2011 not work

[garabounga]

Hallo Guys,

Maybe it has been discussed already but i couldnt find a detailed information about it how can i do the assyst with digiprog for exampel for a car with 128000 km .

km thnks for you answers

[skens]

hi
neeed info,picture,position etc new dashboard twingo 2014
thx

[teerak2uk]

hi
neeed info,picture,position etc new dashboard twingo 2014
thx
Is that the same as I would like!!!!

[viliukas]

Please help me identify this chip, which i found in OBD2(ST16) cable.
340011

[shirokov]

HEF4049BT

http://www.alldatasheet.com/datasheet-pdf/pdf/255334/NXP/HEF4049BT.html

[viliukas]

HEF4049BT

http://www.alldatasheet.com/datasheet-pdf/pdf/255334/NXP/HEF4049BT.html
i looked very carefull,in my case it is CD4094BM. I think it's differences than 4049(i'm lokking pinouts).

[ibratex]

Hello mates ...
Digiprog v4. 94 clone can do range rover 2006 sport ?? I think it is 35080 don't know yet didn't open

Any one did by digiprog or upa ?

Sent from my SM-N900 using Tapatalk

[teerak2uk]

It will do it use new or erased chip

[ibratex]

Ok thanks bro

Sent from my SM-N900 using Tapatalk

[PremierD]

i looked very carefull,in my case it is CD4094BM. I think it's differences than 4049(i'm lokking pinouts).


mr google................... (http://lmgtfy.com/?q=http%3A%2F%2Fwww.ti.com%2Flit%2Fds%2Fsymlink%2F cd4094b-mil.pdf)

[Radek2000000]

Grande Punto EVO 2011 dash-- obd OK.... fiat doblo :fat:

[ibratex]

Golf 6 2012 obd ok

Sent from my SM-G850F using Tapatalk

[Dayo]

Hello mates ...
Digiprog v4. 94 clone can do range rover 2006 sport ?? I think it is 35080 don't know yet didn't open

Any one did by digiprog or upa ?

Sent from my SM-N900 using Tapatalk

I just clip onto these up to 2008. My digi writes on board without erasing. I think there the 35080 6 chips


Sent from my iPhone using Tapatalk

[ibratex]

Wow thanks for info

Sent from my SM-N900 using Tapatalk

[Music73]

I just clip onto these up to 2008. My digi writes on board without erasing. I think there the 35080 6 chips


Sent from my iPhone using Tapatalk
That takes some big test1cles if they... think I would play safe and use new chip... then erase and keep v6 for another job once all working... or at the very least make sure have a good back of the dataset..

Sent from my SM-T533 using Tapatalk

[zecamaneca70]

Hi Guys,

I will have next week my first BMW F31
does the clone 4.94 makes it?
is it chip 35080?

if someone can help i am very apreciated.

Thank you

[teerak2uk]

Hi Guys,

I will have next week my first BMW F31
does the clone 4.94 makes it?
is it chip 35080?

if someone can help i am very apreciated.

Thank you
160DOWQ and wouldn't try it with digiprog

[zecamaneca70]

160DOWQ and wouldn't try it with digiprog


can you explain better, please

[teerak2uk]

can you explain better, please
Codiprog and calculate dump manually and add a blocker

[zecamaneca70]

Codiprog and calculate dump manually and add a blocker

blocker to f31, equal to witch one?

thank you

[javyb]

blocker to f31, equal to witch one?

thank you
Your obviously new to this. I'd walk away and leave the car. As with blocker customer will get caught at dealers and cone back to you.

[zecamaneca70]

Your obviously new to this. I'd walk away and leave the car. As with blocker customer will get caught at dealers and cone back to you.

yes i am new compared to you guys but to take dash and install a can blocker is "easy", just the question that cas4 can blocker are not speaking about the f31 except the new canemu.

my question about the blocker was if the canemu or other makes the job?!?


about costumer i will have to tell him about that dealersheap can read old value but 99% times dealers can read original if they want because they are stored in our days in a lot of places like abs, airbags, gearbox,....


if you can help in some advice i will apreciate

Thank you

[javyb]

Buy a geko blocker from enigma there good, Can-emu won't work

[bersch8688]

Digiprog v4.94

- Skoda Roomster 2009 ---> Diag work Perfect

[claudio35]

vw eos 2007 ---> Diag obd2 work

[Dayo]

Has anyone been successfull doing a bmw e39?


Sent from my iPhone using Tapatalk

[makadam]

Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok

Sent from my Redmi phone

[bersch8688]

Digiprog v4.94

Opel Insignia 2014 ---> OBD Work perfect

341130

[Dayo]

Digiprog v4.94

Opel Insignia 2014 ---> OBD Work perfect

341130

Your brave lol


Sent from my iPhone using Tapatalk

[PremierD]

Why mate .. you pay your money you take your chances ... :) .. done a few of them lol

[Berubeg]

Someone try to keep Dsg fonction of golf 5 for golf 6 because in 6 menu don't have dsg

[bodzio012]

Yes, you can use golf V or other group vag

[aem]

SKODA Fabia 2009 obd ok. fabia -diag-read ?-write ok. (digi4.94)

[Faraday]

Passat b5 2003 tdi digi 4.94 all ok

[ibratex]

hello audi a4 2012 obd tooook looooooooooooooooooooooooooooong time while reading , i decided to eeprom it and digiprog did it well and fast ....

good luck all

[Dayo]

E39 m5 dash done with digi using st47


Sent from my iPhone using Tapatalk