C1 AYGO remote control

[kuti]

Hi
Anybody knows something about remote control locking in this model ?
How it works ? I know that it is separate box one for immo and one one for remote locking but it is possible to write used fob to get it work? PCB is very similar to other peugeot like 206 ...
I didn't find any connection of remote box to diag socket or immo box just stand alone ?
Even if trnsponder is match with FOB how info to remote lockng box is transfered when program new key....

[Snowy79]

The remote part of the key should be seperate from the transponder. It's a manual process to program the remote in and second hand remotes can be used.

[keygargoil]

i did a remote for a aygo the other day the process is a little different than the normal toyota remote procedure

[kuti]

Could You describe how to program used remote ?

[VTS_Tibi]

Time bump this old thread.

Bought myself a Peugeot 107 1.0i, but it only has one key and I would like to make an other one. I want to use a USED remote. (Buy a used 107 key fob with PCB and buy a new housing with uncut blade from Ebay. Have it cut, than install the used PCB in the housing)

How can I program the immobilizer and remote to

1. start
2. open & close

the car?

[keygargoil]

programme the chip by obd id70 if you have a working key and programme the remote seperately

[kuti]

Procedure to rpegram remote:
-put ignition on then off
-open and close driver doors 2x (leave open)
-put ignition on then off
-open and close driver doors 2x (leave open)
-close driver door
-lock doors
-put ignition on and off 2x
-open driver door

Now you are in programing "mode" press lock door on remote 2x remote shuold be added.

[VTS_Tibi]

Would the aforementioned procedure work with used remotes? (so adding a remote which was previously used by an other car)

[VTS_Tibi]

Additionally, is the 107 remote the same as the usual Peugeot 206 / 307 / etc. remotes?

Or should I buy a 107 specific used remote - being Toyota related, so maybe a bit different!?

[Snowy79]

Second hand remotes can be used, just replace the transponder chip to start the car.

[kuti]

Second hande remote fob will work but must be from 107 aygo etc. 206 will not work i tried program without success

[tdor49]

Second hande remote fob will work but must be from 107 aygo etc. 206 will not work i tried program without success

Hi mate
if you just want a second key for 107,C1 or Aygo you can use any second hand key, as long as it's from a 107 or C1 or Aygo, and you don't have to replace the chip.
They use toyota type 4D chip and all you have to do is add a key using Peugeot Planet or Lexia I believe you can use AD100 too but I haven't tried it.
If all keys are lost you have to virginise the immo box but if you have a working key all you have to do is add the second key.
It will ask the question 'do you have a key' you press yes then continue on.
Done hundreds of them!!
Happy New Year !!!

[dexter321]

Hi. Thank for istruction:)

[autochei]

NOTE : Ensure Ignition switch in OFF position and driver?s door open.


NOTE : This procedure must be completed within two minutes.


1. Switch the ignition ON and OFF.


2. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.


3. Switch the ignition ON and OFF.


4. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.


5. CLOSE the driver?s door.


6. LOCK the door using the door lock button on the door.


7. Switch the ignition ON and then OFF.


8. UNLOCK using the door lock button on the door - the locks will cycle to indicate programming mode.


9. Remove key from ignition.


NOTE : Some models require you to leave it in the ignition.


10. PRESS and release both LOCK and UNLOCK buttons on the remote transmitter.


11. PRESS and release LOCK button on the remote.

[Buddy41]

NOTE : Ensure Ignition switch in OFF position and driver?s door open.


NOTE : This procedure must be completed within two minutes.


1. Switch the ignition ON and OFF.


2. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.


3. Switch the ignition ON and OFF.


4. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.


5. CLOSE the driver?s door.


6. LOCK the door using the door lock button on the door.


7. Switch the ignition ON and then OFF.


8. UNLOCK using the door lock button on the door - the locks will cycle to indicate programming mode.


9. Remove key from ignition.


NOTE : Some models require you to leave it in the ignition.


10. PRESS and release both LOCK and UNLOCK buttons on the remote transmitter.


11. PRESS and release LOCK button on the remote.


I try this procedure for Aygo with used circuit board but would not accept it.

I see above now member mentions ignition on & off 2 times.

Is there any other procedures I can try as car is not local.
Aygo 2013 2 Button

[rob h]

Not all are equiped with central locking.
So they also dont have the remote receiver installed.

keydiy does list this remote, and possible xhorse.

[Buddy41]

This car has central locking.
Customer has one remote key at present but requires a spare.

[szengen]

peugeot + toyota, next cooperation citroen crosser + mitsubishi, remote besides authorized serivis, any ideas?

[newone]

I try this procedure for Aygo with used circuit board but would not accept it.

I see above now member mentions ignition on & off 2 times.

Is there any other procedures I can try as car is not local.
Aygo 2013 2 Button
you can not adapt used remote,new or kd will be ok

[Buddy41]

Hi
Why do you say a used item can’t be adapted?

This key has a separate 4D chip.

[szengen]

old megan scenic also has 4d, I have not seen someone coded it again, I can be wrong, I can not see the clones of these keys.. "remote synchro +4d... id 60..1,2,3,4,5,6

[HeXeN]

https://www.youtube.com/watch?v=fCiJiR4RF-c

[newone]

Hi
Why do you say a used item can’t be adapted?

This key has a separate 4D chip.
virgin remote when programmed to car gets locked to the specific car and can not be readapt to another,there is a thread of mithod who tried to renew used remotes and now shooting makes a try again

[Buddy41]

Hi,
I tried that process but only worked for original.
I have now left the job.

Thanks

[HeXeN]

what you mean process worked for original? for completely new remote from dealer or new made by KEYDIY?
I wonder if keydiy works 100%.

[newone]

what you mean process worked for original? for completely new remote from dealer or new made by KEYDIY?
I wonder if keydiy works 100%.
kd works ok,remote must be v3.0

[bero]

You CAN reprogram used remotes without a problem.
And KD does a good job on it. Had a C1 today. First tryd on a NB multifunctional remote with KeyDiy X2 (new function), but the car rejected the remote (did detect it, but opens/closes 2x after pushing the button).

[newone]

You CAN reprogram used remotes without a problem.
And KD does a good job on it. Had a C1 today. First tryd on a NB multifunctional remote with KeyDiy X2 (new function), but the car rejected the remote (did detect it, but opens/closes 2x after pushing the button).
you can not program used remotes,there are threads here from members mithod and shooting with far better knoweledge than me who try to renew those remotes,also no nb remote,only b with seperate transponder

[RFRemotes]

you can not program used remotes,there are threads here from members mithod and shooting with far better knoweledge than me who try to renew those remotes,also no nb remote,only b with seperate transponder

You're talking about completely different things here. PSA remotes has nothing to do with Toyota Aygo/C1/Pug107. They use different algo and even PCB of both types looks the same - they are NOT. Firmware in MCU has nothing common in between. PSA are pain in the @ss but Aygo's can be reused more easily.

[newone]

hi,i was talking about bero post from above who was saying you can reprogram used remote,as far as i know to take a used remote and simply program it to another car (107-c1-aygo) just that is not possible,,it must be renew first if i am not wrong off course,so if it another option can you share the way?

[rob h]

I programmed a few used remotes, works fine.
There i no need to renew.
Just follow the procedure, and make sure the car is equipt with central locking system.

[rokibar]

I programmed a few used remotes, works fine.
There i no need to renew.
Just follow the procedure, and make sure the car is equipt with central locking system.
---------------agree-----------------------

[newone]

thanks,never tryed used on these as i thought there was like the other psa 2b non flip remotes
can someone post pcb of those and what is written on?

[rokibar]

thanks,never tryed used on these as i thought there was like the other psa 2b non flip remotes
can someone post pcb of those and what is written on?
who can read content from c1,p107 toyota aygo will see same data in all remotes. in other psa remotes it is diferents always.

[HeXeN]

Now trying kd remote to program to C1 and not possible!!! s..t
car confirm to see remote (2x lock/unlock) but after I end procedure (ign on off) then only original remote works, kd remote not work.

[newone]

Now trying kd remote to program to C1 and not possible!!! s..t
car confirm to see remote (2x lock/unlock) but after I end procedure (ign on off) then only original remote works, kd remote not work.
use remote with pcb v3.0 and will work

[HeXeN]

I specially bought toyota new shape remote 3button :/ (its printed on battery holder B13 v7.0 180514) K801 on pcb.
which one are v3.0 ? I tried VW 2 button also and no go.

[newone]

V7 will not work friend you must use v3,i have many styles with v3 and works ok ,find a v3 and you will see