FORD ESCAPE 2011 DOESN'T START AFTER PROGRAM 2 KEYS WITH AVDI ABRITES

[abadcinho]

Hi Friends
I Have a big problem with Ford Escape 2011, I'll tell you what I did, the car was running, the customer had only one key that could start it so my customer needed one spare key to add to VEHICLE. In the first tried AVDI couldn't add the key then I tried with SBB that couldn't too, so With AVDI I erased all keys and automatically added 2 keys old key and newer key but when I tried to start the car with both keys that was added successfully car didn't start and immo light after 4 seconds started to blink the same with second key so I test and in PCM there was p1602 and INSTRUMENT CLUSTER reported u2511 so I did a PATS INICIALIZATION and after that immo light is steady with both keys and there is b2141 on Instrument cluster and p1602 on PCM. That's not all Today I tried to program new keys in a FORD ESCAPE 2009 and the same problem.
I forgot to say that I'm using oem keys and any help would be appreciated.

THANKS IN ADVANCE

[itrade]

Quite simply, ........... AVDI not work !

You are not alone

[abadcinho]

ARE YOU SURE?
Maybe you are right but I would like to help me. I need solutions. there are some procedures that can I test.
Regards

[ray-ray]

The 09 model use a 40 bit (8 cuts) 599114 key 4d63
The 11 model use a 80 bit (high security) 4d63+(trick>>program remote section first follow up by key.
Light solid (ready to learn 2 new keys)
T-code pro or MVP pro

[abadcinho]

hanks ray ray
I Managed to program 2 keys and the remote keylles in both vehicles but when I put a programmed key and turn ignition on the immo light is steady and after 1 minute aproximately turn off and the car doesn't
start and have p1602 code in PCM and B2141 on Instrument cluster

[abadcinho]

hanks ray ray
I Managed to program 2 keys and the remote keylles in both vehicles but when I put a programmed key and turn ignition on the immo light is steady and after 1 minute aproximately turn off and the car doesn't
start and have p1602 code in PCM and B2141 on Instrument cluster after pats inicialization

[cklair]

do you have ford ids may be that is the only sloution .if one key is wrong and you have resert the pats then it would not start.becuse you must have two good keys.if you go in dataloger and see how many keys are stored.or get the second good/right key and reprogram just to veryfy if it is not a bad key.

[abadcinho]

I was thinking of buying a subscription and do it by motor craft Web using AVDI AS PASSTHRU interface what do you think

[abadcinho]

PLEASE DK members I need help with this car

[Fallen]

What is the ID of the keys your trying to program in?

I have heard that AD100PRO can't do the latest fords and they have to be done with IDS.

[abadcinho]

The vin of the car is 1FMCU0D70BKC04759 and the ikts that are programmed fcc Id : 0UCD6000022
IC : 850K-D6000022, When I read this ikts zedbull reported 4d63 dst PLUS.
The key that could start the car before I erased keys is only 4d63 and it has a S on blade

[Fallen]

Try programming in the original with another 63 mate. Dst plus is 80 bit

[abadcinho]

I forgot to say that I have three keys programmed and the rke Functions correctly but the car doesn't start.
The code b2141= Non Volatile, Memory configuration (pcm I'd not stored) in Instrument cluster

[abadcinho]

I forgot to say that I have three keys programmed and the rke Functions correctly but the car doesn't start.
The code b2141= Non Volatile, Memory configuration (pcm ID not stored) in Instrument cluster is present

[abadcinho]

Please Someboby Help me

[abadcinho]

PROBLEM SOLVED I don't know how but car start after PMI using PASSTHRU AVDI and charge battery until 13.4 volts

[djjazzer]

PROBLEM SOLVED I don't know how but car start after PMI using PASSTHRU AVDI and charge battery until 13.4 voltsJust had a similar problem with an 09 Escape. Once in PMI what steps did you take.

Sent from my ASUS_Z00AD using Tapatalk

[cyril]

hello pls i have same problem loss the keys for escape how can we do it ?