VW Amarok 2012 lost the keys

[KFZ]

Hi all
I have got Amarok without keys all key are lost ,, and Ihave Chinese AVDI ..
any Idea to program key to it ?Thanks
I have read the Eeprom from dash it is 24Lc32,and it is EDC17C
03L 906 012 AQ

[keygargoil]

its micronas and 24lc32 vdo type cluster you need to read the micronas aswell as the micro for the immo data block to be able to make and add keys

[KFZ]

Hi
will you show me the procedure please I am new in this please
Regards

[keygargoil]

if you have avdi you can go into key learning and it will autodetect the ecu and pull 6 bytes of cs then scan for the7th byte
if you cannot get the cs and pin from the ecu it will need the clocks to be read on the bench you will need a eeprom reader to read the micronas 10 wires need to be soldered down

[KFZ]

if you have avdi you can go into key learning and it will autodetect the ecu and pull 6 bytes of cs then scan for the7th byte
if you cannot get the cs and pin from the ecu it will need the clocks to be read on the bench you will need a eeprom reader to read the micronas 10 wires need to be soldered down
Hi
Thanks , but dosent access in autodetect,, but you mean after service mode and solder the IC back to the dash it can read Auto detect.
regards

[leandroks]

yes m8 u have to write it to service mode before make de dealer key.

[RAFIS]

Use immoPlus soft with VVDI and any eprom reader

1)read eprom from 24c32 use any programmer and save as ori.bin
2)Lostall keys NEC 24C32 Load orginal, Prepare Special Eprom and save as prepare.bin
3)Write PREPARE.BIN to 24c32
4)put back 24c32 to dash
5)Go to normal function 24c32
6)Now you can read immo add keys change milage etc.

[yugo45]

Smoke tool can do this as well.

[achaccha]

Dear Friend.
I am quite sure that avdi ORIGINAL work done in 5 minutes. but I do not know if Chinese clone tool AVDI have that goodness. the steps are simple. enter dashboard - read nec24lc32 - Service mode - set a key - put a TP08 in the TAG key tool - OK and ready. if i get access to "team viwer" we can try.
regards

[roth18]

Dear Friend.
I am quite sure that avdi ORIGINAL work done in 5 minutes. but I do not know if Chinese clone tool AVDI have that goodness. the steps are simple. enter dashboard - read nec24lc32 - Service mode - set a key - put a TP08 in the TAG key tool - OK and ready. if i get access to "team viwer" we can try.
regards

With all keys lost the dash will not let you to enter the service mode via OBD, have to read/write manually.

[Maartinj]

With external programer it is a 5-10 min inc disasembly and assembly cluster.
VVDI is very good for this.
No need to read NEC, only eeprom ,and follow procedure in options " all key lost"

[achaccha]

Dear Friend
if you choose, maybe you can give via team viwer asitencia. but you can see from the following link the procedure.
https://www.youtube.com/watch?v=MYuS1Ub-3Xc
luck

[topclef]

Now , With Original AVDI (V18.0) , you can do it without need to remove dash and modify eeprom dump for VDO-NEC , all by OBDII , you've special Button ( ALL KEY LOST ).

[sparkz02]

So AVDI original can do these lost keys without the need to open dash, has anyone tested as of yet?

Thanks