Mitsubishi L200 all key lost

[fazal]

Dear all i have to program the key for Mitsubishi L200. i have the MVP pro (original UK), T300, and SBB. i am trying but all time it show the "Eror" in the programming procces. so please explain that which 4d chip will work for this car. and if there any other way for programming the key. so please inform me. the Engine ECU and Immo deatail are below.

Engine ecu. MR577084
Immo box. MR587390

[autoenthu]

L200 after 2006 uses PCF7936,

[manasrah]

l200 2006-2009 use
ID:46 Locked
PCF7936 and u can make
8key

[fazal]

my dear friend i have tried the 46, lck46, id60 and id61 but all showed "Error" during programming procces. please give me any other way to start the car. my all programmer show the same problem. please guide me any good solution. i am waiting.

[yssf]

you can also get key from eeprom(cloning),or writing key tiris in dump

[keysph]

Provide Year of the car if you want help!

[fazal]

my friend the car is L200 year 2001 model ( K74TGJENXFR6 ). and i have not found any 8pin eeprom in the immo box or ECU that contain the Immo dumps. i think this model of mitsubishi will not have these types of eeproms and the program will be in the main ics. the photos are attaced.

[keysph]

You need 4D chip with ID 61 for Mitsubishi and with pin 3828 you must be able to program it with any of your tools.

[fazal]

ok thanks my friend but i have tried many times but all time it failed. and show a massage "ERROR" during the programming process. is there any other way to put the key in the system.

[manasrah]

hi my friend u must used D:46 Locked

[qwertyuiop12]

Hi,
1 1999-2002 60 ID (4 d)
2 Check the immobilizer antenna pumping
3 make a diagnosis
PS: If everything ok no problem staying up ID60 MVP and SBB

[keysph]

Right, it's my mistake It's ID 60 and the pin is the same 3828

[fazal]

my dear friend i have also checked this type of transponder chip. ok i have noted in defrent keys that mostly the id was same but still there are the defrence in thair datas in the transponder cheching machine. so can u show me any conform id 60 data that will work for this car. then i will find that type of id 60 and will try to programm.

[fazal]

dear keysph (http://www.digital-kaos.co.uk/forums/members/236256-keysph/)
i am online now can u come with me at skype to find out the solution for my problem.

[fazal]

if any one have the ecu pinouts ( wiring diagram ) for this car please send me i want to check its conection.

[keysph]

There is no ID60 special transponder for this car.
The problem is other. Check fuses and do a diagnostic on the car.

[autoenthu]

With id 60 with the pin 3828 Leave ign on for 35 min, and do progaramming

[siyadk]

Mitsubshi is known to go lock mode when an un programmed key is made to start with.
Leave ignition on for 35 mins and see what happens

Sent from my GT-I9300 using Tapatalk 2

[fazal]

Thanks to all,
i have succeeded to progrqamm the key for my L200 K74 (diesel). ID61 is the correct transponder chip for this car. i have also the wirring diagramm for this car, if any one need it, i can provide. thanks again for your all support.

[DOUGLASDL]

Good day friend could send to me thank you

[curtpza]

So what was the problem? Because you said that you did try ID61 and it didn't work. What did you do different that made it work? Did you leave ign on for 35 min...was this the solution or was there some other fault that you cleared?

[fazal]

Thanks all,
i have succeded to programm the key for mistsubishi l200. the correct transponder for this car is ID61. i also have the wiring diagram for this car (L200 K74 Dieasel), if any one need i will upload it.

[fazal]

actualy i was programming the key for that car on a table not in the car. so when i was checking the ecu connections i have found that some ground points of the wirring was not connected to ground. then i have connected them and as i start to program the key on T300 it started the programming and asked the next key.

[makura]

May i have the diagram please mate?

[alclot]

Hi mates,
I have the same car which I need to match immo box with ecu. Which is the ee inside immo box? I see one e2prom but I know which one is.
Thanks a lot ;)

[systemlinux]

Upload the info and reading of the ecu and we make it immo off.

[perfido]

Hi mates,
I have the same car which I need to match immo box with ecu. Which is the ee inside immo box? I see one e2prom but I know which one is.
Thanks a lot ;)
use 68hc805P18

[ngakson2002]

Hello Mate

For immobox have a look at the Post #7 here.It contains a Motorola 44 pins known as 68hc805P18.Tmpro2 read this MCU without problem.
For transponder, it uses the ID 4D61.You can try to program this via OBDII using T300, SBB or any other tool.

BR, Serge

[mecanicaina]

I had the same problem the t300 gave me error and the fault was the cylinder switch that does not detect the key put the chip is an id61