Renault megane 2003 year 19 dci pinout

[carsofting]

Hi

Renault megane 2003 year 1.9 dci pinout i need of ecu , please

thanks advanced

i get the pinout and all is OK, so the problem with car is the when i want the start the car , car no start every time , he start normal 5 times and after 20 min when i want start , only FAN working and i can't start the car .... can anyone help me ???
( when he can't start , working fan and with cardiagnostics i can't see example sw version etc , but when i start the car then i see sw hw and other details normal FROM ECU.... )

thanks

[carsofting]

PLEASE HELP

thanks

[carsofting]

... no one can't help me ????

[genius76]

here is a 5 engines, engine code neeeeeeed

[carsofting]

code 0281011275

i check wire and all is ok

i really don't know what is the problem .... heeeeelppppp please

[genius76]

if fan working that's men ECU not getting feed, fan forking in emergency mode when no signal from ECU
check ignition contact / relay for ECU / connector to ecu / or in most cases MINUS

engine code i mend F9Q****

[carsofting]

please can you send me pinout , i would check minus , this i not check

[miha99]

EDC16C3 ECU.

[cagatay87]

Hi

Renault megane 2003 year 1.9 dci pinout i need of ecu , please

thanks advanced

i get the pinout and all is OK, so the problem with car is the when i want the start the car , car no start every time , he start normal 5 times and after 20 min when i want start , only FAN working and i can't start the car .... can anyone help me ???
( when he can't start , working fan and with cardiagnostics i can't see example sw version etc , but when i start the car then i see sw hw and other details normal FROM ECU.... )

thanks

could you please upload your ecu's pictures friend?i need back side please.i dropped some components near bosch 30505 ic.please help

[Meat-Head]

could you please upload your ecu's pictures friend?i need back side please.i dropped some components near bosch 30505 ic.please help


right, got one in hand, been using it as a stepping stone for months, 0 281 011 776

just found packet of wine gums as well, just trying to get back off, if it don't come off, tough

[cagatay87]

can you take pictures for me?

[Meat-Head]

can you take pictures for me?

yeah just on it now, had to get Torx(R) screws out, then use bedside hot air gun to get back off, had it hotter than the *HOT* bird from the parts place. Then took photos, then have to upload to computer.

What country are you in?

just sucking off camera now BRB

[Meat-Head]

arse wipe computer froze solid

here to prove i wasn't lie about wine gums there in second photo

[carsofting]

i have not more car at service :(

[carsofting]

i check all wire and still is same problem , i have not any idea where is the problem , i also desolder ecu and bsi complet .... hae anyone experiences with this problem ???

[genius76]

sou you checked pus minus to ECU also shut be edc15 not 16

[carsofting]

yes... i check all plus and minus ... also relays ... and still problem same problem

[genius76]

sou ecu gets feed and you cant get diagnostic on bench ?

[carsofting]

yes, when car can't start the problem is like have not plus or minus , and i can't read example sw version of ecu etc .... i check plus minus and all wires and all is ok

[genius76]

on desk ???

[carsofting]

i test on car alll...

[genius76]

so try on desk, and you will sure, where is problem mate

[kostovnikola]

I have problem like this.Solution was another computer and copy paste with BDM.

[miha99]

Agree with kostovnikola, Motor ECU does`t communicate VIA can line and the resault is locked system (motor fan run and no info from motor ECU to diagnostic device).
If you copy content to new ECU than eeprom, flash and mcu config must be copied!

[Meat-Head]

sounds more like lost an ignition feed.

rip the battery out, and use a ice pick to remove the tape off the loom as it runs in front of the battery

also remove the wheel and cover on same side as battery and check loom chaffed in wing ding

[carsofting]

i test all but nothing , tomorow i will try change the ecu ....