Seat Cordoba 6L adding a key

[simaservis1108]

Hello,

Can anyone help me precode id48 for this car?
I read 9S12H256 dump from dash,got pin,just need to help me precode with Zed-Bull.
Here is the dump:
1.rar download - 2shared (http://www.2shared.com/file/yQ5cIY8N/1_online.html)

With kind regards,
Sima

[kiszka]

SEAT

CORDOBA
1996
1998
Transponder Philips ID33 PCF7930 - PCF7931



SEAT
CORDOBA
1999
2002
Transponder PHILIPS Crypto ID42 PCF7935AS precoded


SEAT
CORDOBA
2002

Transponder Megamos Crypto 48 - ID48




new 48 is ready for programming

[simaservis1108]

Just out of the box,put in new key shell,go to channel 21 and insert new key?

Kind regards

[lesakljucevi]

No need precode transponder,you have pin code,just learning key used sbb,t 300, mvp.vag commander...

[simaservis1108]

It won't learn,says key error,using VCDS.

[kiszka]

Select
17 - Instruments
Meas. Blocks - 08
Select Block 022.
Go!
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to
transponder is locked
Immobilizer.
You can check each key in this manner

[simaservis1108]

This it the problem I think,my Cordoba is MY 2008,and it's a new type key.




SEAT
IBIZA
2004
2008
Transponder MEGAMOS Crypto CAN


How to precode to SEAT CAN?

[Vladko]

No need to precode,go to 25 immobilizer there you can add key.Need only PIN,and if car is in lost keys situation,you have to wait security wait time.

[simaservis1108]

It's not possible.
Here is what I do:
1)25-Immobilizer
2)Login-enter pin code(success)
3)Adaptation
4)Channel 21
5)Shows 1,I enter 2,press test and it says Error("Save" button greys out).
It won't let me code new transponder,original passes the coding phase.

[H.Wessel]

Here is what you have to do:
1)25-Immobilizer
2)Login-enter pin code(success)
3)Adaptation
4)Channel 1!!!!!!

[simaservis1108]

Thank you,will try it out tommorow.Will post results.

[robert81]

as far as im aware 6l immo is coded via instruments not immobiliser.
its k-line car not CAN.
first of all you should turn ignition on and delete faulty codes from engine and instruments.
then yuo can code keys.
i had similar situation few times and usually faulty codes were causing problems

[simaservis1108]

I tried today everything.
Tried both channel 1 and 21.Tried to code it into instruments.In instruments channel 21 isn't allowed.Also deleted all DTC's.
The damned thing just won't code.I am a little bit stuck here.Any suggestions on what should I try next?

[potatodog]

ECU have IMMO off?

[simaservis1108]

I don't want immo off,because I have 1 working key,want to add 1 new key...

[keysph]

Select Block 024.
[Go!]
Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).


If the lock times are NOT 0:

Do NOT switch off the ignition!
Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.





Than try with



[Login - 11]


4-digit PIN

Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.



[Do it!]


[Adaptation - 10]
Enter 21 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]



Repeat the following steps until all Keys have been matched:

Switch Ignition OFF and remove Key.
Insert the next Key and switch Ignition ON.
The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.

[simaservis1108]

Solved.....

[keygargoil]

just use standard id48 and pin code 05581 and do it
your file size should be 4k not 2048 bytes

[simaservis1108]

as far as im aware 6l immo is coded via instruments not immobiliser.
its k-line car not CAN.
first of all you should turn ignition on and delete faulty codes from engine and instruments.
then yuo can code keys.
i had similar situation few times and usually faulty codes were causing problems
Immo is integrated into instrument cluster,but it is coded as 25-Immobilizer.

[simaservis1108]

just use standard id48 and pin code 05581 and do it
It was SEAT CAN transponder,I have a Cordoba with new Immo system.

[keygargoil]

i have loaded your dump into my software there is 2 keys coded use a t6 id48

[simaservis1108]

Solved already,thanks all for help :D

[kiszka]

IMMO 3
Determining IMMO-ID & VIN

[Select]
[17 - Instruments]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Key Matching

Prerequisites:

All keys are either new or were adapted to this car (IMMO-ID) before.
You can match up to 8 keys.
While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
Battery voltage at least 12.5 V.


[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 022.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.


Select Block 024.
[Go!]
Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).

If the lock times are NOT 0:
Do NOT switch off the ignition!
Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.

[Done, Go Back]


[Login - 11]

4-digit PIN
Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.

[Do it!]


[Adaptation - 10]
Enter 21 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

Repeat the following steps until all Keys have been matched:
Switch Ignition OFF and remove Key.
Insert the next Key and switch Ignition ON.
The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.

Note: The above steps must be completed within 60 seconds after saving the Adaptation!



Immobilizer IV Key Matching

This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer IV

Determining IMMO-ID & VIN

[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]



Key Matching

Prerequisites:



All keys are either new or were adapted to this car (IMMO-ID) before.
You can match up to 8 keys.
While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
Battery voltage at least 12.0 V.


[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 001.
[Go!]
The value in field 3 must be Yes. If value is No, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.

Select Block 003.
[Go!]
Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).



If the lock times are NOT 0:

Do NOT switch off the ignition!
Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.



If lockout time was present check Group 1.3 as mentioned above to confirm "Yes" is shown.
[Done, Go Back]


[Security Access - 16]



4-digit PIN

Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.



[Do it!]


[Adaptation - 10]
Enter 001 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
The old keys are automatically being cleared.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]



Repeat the following steps until all keys have been matched:

Switch ignition off and remove key.
Insert next key to ignition and switch ignition on again.
The warning light for the Immobilizer will light up for ~2 seconds, then go out.



Note: The above steps after saving the adaptation, should not exceed 60 seconds!


f not for the work you should double-check the synchronization between the engine and take pictures of the counter (measuring blocks) channels 21,22,23,24 immo3, immo 4 channel 1,2,3,4 or 21,22,23,24 and insert here immo 4 a temporary shutdowns that have cool one's heels