***Toyota Smart Lost Key Solution - No Id code needed***

[simon77]

i can any one help reset this immo box 89990-52260.

[usman4]

here's your reset

[simon77]

thank you usman4 worked first time
regards

[usman4]

anytime.. and by the way its smart not immo :D

[simon77]

usman4 please could you do this one for me Smart key!!
regards

[usman4]

here u go.........

[Jhone smith]

Hello Anyone help me for renualt fleuance 2011 odo Correction Data lines..

[siyadk]

Hello Anyone help me for renualt fleuance 2011 odo Correction Data lines..

wrong thread mate....

[Johnner]

Hello Anyone help me for renualt fleuance 2011 odo Correction Data lines..



Jhone mate..please introduce yourself first here : Introduce Yourself (http://www.digital-kaos.co.uk/forums/forumdisplay.php/2-Introduce-Yourself)

[LEORNARD NKATA]

hie guys i have a toyota auris, the immo box was stolen and i want to replace it with another one so I'm looking for help on hound match it with the computer box and the key

[aketokediag]

Could you post your dump here i will virgin it for you. or try this method try and perform syncronize between the ECU and IMMO open driver's door, turn ignition ON short terminals Tc (PIN13) CG(PIN5)in the DLC/OBDII connector leave it for 45minutes the car should start

[LEORNARD NKATA]

ok thanks so much will try during day time tomorrow and i will report back thanks so much.

[aketokediag]

You are very welcome

[aketokediag]

Hello M8,
I have highlander 2008 all key lost i noticed the vehicle did not have receiver it will be very difficult to reset through obd because if i do so, i would beable to program key to the car, i will be glad if anyone can help me add up used key to dump, smart details 89990-48020 232500-2771, I will add the dump as soon as i remove the Smart Key and post keydata
Regards

[aketokediag]

Hello M8,
Here is the dump please help to add key to dump
Regards

[Nerox]

Hello,

I Feel kinda stupid but.. I've haven't found the main thread explaining what should i post here

I'm trying to add an used key to a Lexus IS 220 D - From what i've seen I Need a "Seed Code" to reset ECU Immobilezer and add both used key (from another car) and the working master key

Any help would be appreciated :D

[aketokediag]

Hello m8,
Try &pm me will try&help you, remember receiver's problem is very common to Lexus car will advice you to get original dump from chip 93C86 first before you proceed obd reset.
Regards

[PremierD]

Hmmmm.................

[aketokediag]

No one is willing to help me out??? I understand not everyone can do this I guess this perticular model is very difficult to handle.
Will look for way to solve it.

[PierreTheron]

trying ,, trying to understand .wish it was only a simple as irf37xx on scenic 2 dash

[PremierD]

No one is willing to help me out???


Nice edit ..... :).....Try &pm me will try&help you

[aketokediag]

Nice edit ..... :).....Try &pm me will try&help you

This man again??? Lolz, I don't knw if this is difficult for people to handle here, will try & look for alternative.
Thanks for your input.
Regards

[Nerox]

Hello m8,
Try &pm me will try&help you, remember receiver's problem is very common to Lexus car will advice you to get original dump from chip 93C86 first before you proceed obd reset.
Regards

Is there a procedure on this post ?.. Don't know how to get the dump :/ .. Except the dump on techstream which allow to create seed code

Thanks in advance !

[aketokediag]

There is, take out smart key out of the vehicle, read S93C86 chip keep the dump, you can reset manually or reset through techstream seed codes. Am talking from experience I had with different Lexus cars.
Regards

Sent from my Infinix X506 using Tapatalk

[usman4]

Aketokediag mate it's not true that no one willing to help but sometimes a person willing to help but he will not as help u which way u want, surely there are some alternatives.. post your id code and smart dump i will reset them then u easliy add used key :)

[aketokediag]

Have already solved my problem, i dont know why people here cant help me if i have Toyota problem, i consider it as racism, but i strongly believe we are one big family. Well thanks to you all.
Regards

[PremierD]

" i consider it as racism" why mate are you a Martian ?

[ibratex]

hello bro ..dont missunderstand the mates in here ,,, some of them are busy as or more than you , hope you dont take it wrong way but i bet you are a good guy lookinfor help , dont worry you will be as you are more active ...chill!!!

[aketokediag]

hello bro ..dont missunderstand the mates in here ,,, some of them are busy as or more than you , hope you dont take it wrong way but i bet you are a good guy lookinfor help , dont worry you will be as you are more active ...chill!!!


Thanks so much

[Tagne]

hello master this my first experience with smart keys
i have keys from dealer from prado 2010 costumer want keys with remote everything ok
as tool i hav x100 i attach key data and smart dump 370350370344370344

[PremierD]

Try that ......................

[Tagne]

Try that ......................
thx you but it not yet come master.....

[PremierD]

it was there for two hours ... :) .. back .. but not for long

[siyadk]

Tagne.. i doubt whether u can program this car with x100.. tried on land cruiser prado last week with x100 and failed. finally did with old t300

[Tagne]

Tagne.. i doubt whether u can program this car with x100.. tried on land cruiser prado last week with x100 and failed. finally did with old t300

thx you everybody car started after resetting ID CODE AND SMART KEYS
everything is OK

[usman4]

.............

[usman4]

Tagne.. i doubt whether u can program this car with x100.. tried on land cruiser prado last week with x100 and failed. finally did with old t300
ask him definitely "Tagne" done this job with x100 :P

[Tagne]

ask him definitely "Tagne" done this job with x100 :P
yes of course i did it with x100 once more for your files

[ivannzowa]

someone help me to renew smartkey and ecu id code for this toyota landcruizer so that i can adapt with key


smart key ecu
toyota
part no 89990-60092


ecu id code
toyota 89784-60030
Attached Files Attached Files

[Afzal k]

your id code dump is read wrong..i have resetted smart box dump

please read id code box dump properly, someone will help reset it for you

pass in pm

[ivannzowa]

help to renew id code ecu
toyota
89784-60030
attached dump

[usman4]

here u go.........

[siyadk]

help to renew id code ecu
toyota
89784-60030
attached dump


it wont hurt for you to start thanking members who have helped you, or else in future your help requests will be unheard

[ivannzowa]

thanks for everyone who helped me with reset dump,am going to try and give feedback

[ngakson2002]

Hello mate,
Please need help for :

1) Reset file of the 93lc46b dump attached from the ESL of a 2007 RAV4
2) Page 1, 2, 3, 4 transponder data to be written in a TPX2 from the Smart box dump attached


Best Regards

[ttzag]

now TANGO can reset smart key 40,80,128 bit

[ivannzowa]

didnt work for me

[cjawahir]

Hello mate,
Please need help for :

1) Reset file of the 93lc46b dump attached from the ESL of a 2007 RAV4
2) Page 1, 2, 3, 4 transponder data to be written in a TPX2 from the Smart box dump attached


Best Regards

here u go bro , if every thing ok with your vehicle , should start .

cj

[ivannzowa]

hello,everyone..am back again,after having trouble with this toyota lancruizer,i decided to buy another used smart key ecu,please someone help me to renew this ecu as well as id code ecu
smart key ecu
toyota
89990-60171

ecu id code
toyota
89784-60030

attached dump

[usman4]

smart reset done. use my previous reset id code file

[ivannzowa]

pass please

[aketokediag]

hello,everyone..am back again,after having trouble with this toyota lancruizer,i decided to buy another used smart key ecu,please someone help me to renew this ecu as well as id code ecu
smart key ecu
toyota
89990-60171
ecu id code
toyota
89784-60030

attached dump

Here you go m8, use this file and report pass in pm please dint forget to push thanks button
Regards

[aketokediag]

now TANGO can reset smart key 40,80,128 bit

THANK YOOOOOUUUUUUUUU
(http://www.digital-kaos.co.uk/forums/private.php?do=showpm&pmid=1828378)

[taxo1965]

Hello
i need your help to get these started,thanks for your time.


P1; 98
P2; E7
P3; 1D 2F 66 (1D)
P8; 98 2B 12 EE AD
Best regards

[PremierD]

Read in 16bit ?....:)

[taxo1965]

PG 94 is not working,Clearly pg94 for older models

Best regards

[cjawahir]

Hello
i need your help to get these started,thanks for your time.


P1; 98
P2; E7
P3; 1D 2F 66 (1D)
P8; 98 2B 12 EE AD
Best regards

here is your file with the key your post , if the key is exact for that vehicle it will start .

cj

[NORSHAN]

HI FRIEND
I need vrigin files for toyota land cruier 2009 all keys lost
smrt key ecu 89990-60141
ecu ID code 89784-60010

[cjawahir]

[QUOTE=NORSHAN;2759416]HI FRIEND
I need vrigin files for toyota land cruier 2009 all keys lost
smrt key ecu 89990-60141
ecu ID code 89784-60010[/QUOTE

this vehicle had lost key before and add one key only , and lost the one key now right

try to write key to dump and see .

cj

[NORSHAN]

plaese any body can add this key to my dump372867
P1: 98
P2: 08
P3: 63 E8 45 1D
P8: 98 2B 15 99 42

[davidjunior]

Key Added My friend


David

[aketokediag]

hello,everyone..am back again,after having trouble with this toyota lancruizer,i decided to buy another used smart key ecu,please someone help me to renew this ecu as well as id code ecu
smart key ecu
toyota
89990-60171

ecu id code
toyota
89784-60030

attached dump

Free for you m8, check and report

[NORSHAN]

so thank davidjunior but my car didnt start never same problem
please friends i need trusted soultion

[NORSHAN]

[QUOTE=NORSHAN;2759416]HI FRIEND
I need vrigin files for toyota land cruier 2009 all keys lost
smrt key ecu 89990-60141
ecu ID code 89784-60010[/QUOTE

this vehicle had lost key before and add one key only , and lost the one key now right

try to write key to dump and see .

cj

yes you are rihgt 100% but i try by resetting and by add key to dump but car didnt start

[kyawkyaw]

[QUOTE=cjawahir;2759477]

yes you are rihgt 100% but i try by resetting and by add key to dump but car didnt start
Fri, can open switch on?

Sent from my GT-I9500 using Tapatalk

[aketokediag]

Hello M8,
If i may ask where did you locate 93LC46 ESL RAV4 dump from? could please specify? where you able to sort it? if no i think i can help you out. Thanks in advance
Regards

[koncimobil]

Disassembly ESL block, you will find eeprom.

[aketokediag]

Disassembly ESL block, you will find eeprom.

Thanks mate will try it... thank you verry much

[hiroto ichinohe]

Hello
How do I to add the smart key second-hand?
My car is a 2008 Estima hybrid AHR20.
ECU is denso89990-28031
Thank you to someone good advice.

377267

[usman4]

give proper info mate. like its all lost or vehicle has one working smart key??

[hiroto ichinohe]

give proper info mate. like its all lost or vehicle has one working smart key??




I have lost all the smart keys.

I purchase used ECU and the smart key to set and one is registered, but wants to register a smart key used one more.

[siyadk]

you need make your used smart key to virgin by tools like tango, mk3 or tm100, after that you can add smart key to the system

[hiroto ichinohe]

you need make your used smart key to virgin by tools like tango, mk3 or tm100, after that you can add smart key to the system

Thank you for good advice.
Besides, is there not the method?
Can you not add a used smart key in skp900?

[usman4]

I will give u reset file tomorrow, write it in smart ecu and program your used key using your skp900.

[hiroto ichinohe]

I will give u reset file tomorrow, write it in smart ecu and program your used key using your skp900.

Hello
I'm sorry, I do not understand a meaning.
I am weak in English, and it is to the thing which translated the English sentence written here in a translation site.
You reset my ECU, and will it be that it allows you to add a used key, and と says?
The thing which I have is only GTS Techstream and EZP2010.
Are you made only from this?
I am sorry that my way of writing is bad

[Brayn]

Hello
I'm sorry, I do not understand a meaning.
I am weak in English, and it is to the thing which translated the English sentence written here in a translation site.
You reset my ECU, and will it be that it allows you to add a used key, and と says?
The thing which I have is only GTS Techstream and EZP2010.
Are you made only from this?
I am sorry that my way of writing is bad
Yes, Siyadk correct you can reset/ virgin your smart key using Tango, MKIII, TM100, iprog+, Zedfull like that if not you should reset smart ecu manualy and programme keys

Sent from my C5502 using Tapatalk

[Brayn]

Aftet long time I'm here. Where is Gwee??
There is a lot of Toyota masters cjwahir, Siyadk, bram380, imfooser, Jonny_D like that lot of there
I need nelp for reset Toyota Id Code box 93c46 but this is 2015 Toyota H type

Sent from my C5502 using Tapatalk

[usman4]

write this file back and program used key with any of obd tool like skp900,x100 etc.

[hiroto ichinohe]

Thank you, everybody.
I will do it tomorrow.
I thank everybody who cooperated.
I report the result.

[ULYSSE77731]

Hi I think the best solution if you did not master the key is with ABRITES tool.
Nissan because as they are rotating and very difficult to add key codes ...
ABRITES or ZBULL

[aketokediag]

Hello
How do I to add the smart key second-hand?
My car is a 2008 Estima hybrid AHR20.
ECU is denso89990-28031
Thank you to someone good advice.

377267


Hello M8,
Here you go, you will not get ignition, just register your key. You can add key with techstream next time you need to post your id code dump.
Regards

[siyadk]

write this file back and program used key with any of obd tool like skp900,x100 etc.


Hello M8,
Here you go, you will not get ignition, just register your key. You can add key with techstream next time you need to post your id code dump.
Regards


Are you sure you can add second hand smart key only by resetting smart ecu....??

[hiroto ichinohe]

Everybody hello
Thank you for advice.
I worked, but cannot register a smart key well today.
It becomes the ignition on, but cannot start a hybrid system.
My car did not work.
Please help me.
The situation does not change even if it goes back up in an original dump …

[Brayn]

Everybody hello
Thank you for advice.
I worked, but cannot register a smart key well today.
It becomes the ignition on, but cannot start a hybrid system.
My car did not work.
Please help me.
The situation does not change even if it goes back up in an original dump ?
You should reset smart ecu and id code box
Post both files here
Actually I don't know about your vehicle details however I can help you if you have smart ecu and id code box dump files

Sent from my C5502 using Tapatalk

[hiroto ichinohe]

You should reset smart ecu and id code box
Post both files here
Actually I don't know about your vehicle details however I can help you if you have smart ecu and id code box dump files

Sent from my C5502 using Tapatalk

I do not understand id code box.
My car is estimahybrid AHR20 for 2,008 years.
Is it by any chance this?
Should I dump IC2 93C46?
But I do not know where is it in.
It was used and bought this.
http://yahoo.jp/box/_enGGM

[Brayn]

I do not understand id code box.
My car is estimahybrid AHR20 for 2,008 years.
Is it by any chance this?
Should I dump IC2 93C46?
But I do not know where is it in.
It was used and bought this.
http://yahoo.jp/box/_enGGM
Send me vin number

Sent from my C5502 using Tapatalk

[Brayn]

I do not understand id code box.
My car is estimahybrid AHR20 for 2,008 years.
Is it by any chance this?
Should I dump IC2 93C46?
But I do not know where is it in.
It was used and bought this.
http://yahoo.jp/box/_enGGM
Yes that's right. Id code box 93c46
Smart ecu 93c86
Send me both files for reset
After you can programme keys

Sent from my C5502 using Tapatalk

[hiroto ichinohe]

OK.

Give me time a little.

I will do a point tomorrow because I am absent.

[davidjunior]

Dear Friend,

Do not need to Reset anything,

I shall repair your bin file and will post it back to you tomorw.

Thanks
David

[aketokediag]

Aftet long time I'm here. Where is Gwee??
There is a lot of Toyota masters cjwahir, Siyadk, bram380, imfooser, Jonny_D like that lot of there
I need nelp for reset Toyota Id Code box 93c46 but this is 2015 Toyota H type

Sent from my C5502 using Tapatalk

Hello M8,
Where you able to make it? if not try and read your dump with 16bit and post it.
Regards

[hiroto ichinohe]

I returned to an original state with the file which I dumped in digiprog.

Thank you, good everybody

Is it impossible to add a used smart key when after all I do not unlock it?

[simon77]

please could somone add this key to dump having some real problems here
98
0D
6804661D
regards

[davidjunior]

Hi Simon77

You need to give us page 8 data as well to add this key up .

Thanks
David

[simon77]

thanks david
i have read with zedbull this is what i get
DATA 98 0D 6804661D
RESPONSE 392675-FB77B6
INFO DST PLUS LLL
CHIP 4D SMART CODE
my zedfull would read it better but it has gone for repair
regards

[davidjunior]

You need to read it with some other machine,
Page 1:
Page2:
Page 3:
and
Page 8:
Otherwise it will not work

[siyadk]

read the the key in any of this
tango,tmpro,tm100,mk3,cn900,tksprog

[simon77]

i got hold of a friends zedfull and programmed remote via eprom. car starts but only if i put the key on the start button. i virgin smart box inserted key data manually reprogrammed key is now working perfectly .only problem now is car starts and switches off after a few secs trying to re-sync and see what happens.
regards to all for you help.

[simon77]

now the car is running thanks to all

[aketokediag]

AM HAPPY FOR YOU

[say882]

Hello please i lost all my smart key for my toyota prado and i have two other key one is new one and the second is used one these are picture of them
i need if some body can program these two key for me,i send file of smart key box eeprom is 93C86

[siyadk]

used added to dump. You will be able to start and turn on ign.

Do add key procedure. When asks for registered key, place used key near ign and then put new key

pass in pm

[siyadk]

Hello please i lost all my smart key for my toyota prado and i have two other key one is new one and the second is used one these are picture of them
i need if some body can program these two key for me,i send file of smart key box eeprom is 93C86


Almost two days and no report or even a thanks. People like you makes contributors to help less for others

[Johnner]

I'm sorry Siyadk,there was no feedback from him,but there never will be,I'm afraid...

[aketokediag]

But why these people are getting banned

[haiz0708]

Hi Mate,
I have 2 pcs Toyota Original Vios H Smart Key buy with Chinese supplier.
I cant use those Smart key add to customer car.
I check both original and those smart key are 433mhz frequency correct.

Please help me check those smart key whether used or brand new.
Is the Pg6 problem?
pg6 is unlock but i cant change value on tango.

[siyadk]

as far as i am aware you cant identify new or used from key data.. You can buy new software for unlocking toyota remotes in tango and can test the remotes if used or blank

Just by having sama frequency doesnt mean the remotes are compatible. I always go by checking original remote pcb and new remote pcb

Did you try to add remote via obd, if so did you get single beep or no beep while adding?

[hiroto ichinohe]

Everybody nice to meet you.
Thank you the other day.
When I copy id71 toyota smart kye, which Transponder chip should I choose?

[haiz0708]

as far as i am aware you cant identify new or used from key data.. You can buy new software for unlocking toyota remotes in tango and can test the remotes if used or blank

Just by having sama frequency doesnt mean the remotes are compatible. I always go by checking original remote pcb and new remote pcb

Did you try to add remote via obd, if so did you get single beep or no beep while adding?

H Smart key i think tango still cant reset right now.

add remote via obd no beep sound while adding.

[Brayn]

Tango can't reset Toyota 128bit-AES keys

Sent from my C5502 using Tapatalk

[siyadk]

[emoji15] [emoji15] yes it can...
You need to purchase the software though

[Siham]

If you mean reseting the key ,yes Tango can do it 100% but if you mean about all keys lost situations and need to reset the immo yes Tango can't do it now ,only MK3 can do it .

[haiz0708]

[emoji15] [emoji15] yes it can...
You need to purchase the software though


What Software need to buy?
Toyota Smart key unlocker?

you mean my Smart key is used condition?

[siyadk]

http://www.scorpio-lk.com/downloads/Tango/News.pdf

check ver 1.104
Need to purchase software for 200 Eur

All lost keys for smart H type:
Only MK3 can do it like Siham said, but its possible to add and reset by manually. Just post the dump and key data here if you want to add keys to dump

[haiz0708]

http://www.scorpio-lk.com/downloads/Tango/News.pdf

check ver 1.104
Need to purchase software for 200 Eur

All lost keys for smart H type:
Only MK3 can do it like Siham said, but its possible to add and reset by manually. Just post the dump and key data here if you want to add keys to dump


now my problem is my H smart key cant use obd adding, i need to know whether my H smart key is used or new key, can you help me to check?380894380895

[siyadk]

:banghead:for the last time.... no one tell your key is used or not from key data(as far as i know).

your only option is to check in tango after purchasing "reset of toyota keys" module

[siyadk]

Everybody nice to meet you.
Thank you the other day.
When I copy id71 toyota smart kye, which Transponder chip should I choose?

tpx2, eh2 or cn2

[rob h]

Aygo, 2015 smartkey 89990-0H030
Is there any id box in these cars?
Which eeprom should be in here?
380966380967380968

[hiroto ichinohe]

Thank you
I copy it

[Brayn]

Aygo, 2015 smartkey 89990-0H030
Is there any id box in these cars?
Which eeprom should be in here?
380966380967380968
c86 chip have. using vin number can check have id code box or not?

Sent from my C5502 using Tapatalk

[Brayn]

MSOP8 c86 chip have back side

Sent from my C5502 using Tapatalk

[rob h]

I can pm you the vin this week.

[rob h]

381017381014 Do you mean this one?
I can pm you my vin this week.
Thanks

[rob h]

I will read it soon, and check it with my Tango.
Or do i Always need a reset for this type. It is with a H chip.

[Brayn]

Yes this is the chip. C86
I think this vehicle have id code box.
This type smart ecu I have virgin file

Sent from my C5502 using Tapatalk

[siyadk]

I will read it soon, and check it with my Tango.
Or do i Always need a reset for this type. It is with a H chip.

unfortunately tango cant reset or add keys to this immo type , as far as i am aware
Also no need to reset as well..
read dump and key data and post it here. Will add the key the dump to start the car

[Brayn]

That's why I said Tango can't do this. Siyadk correct. Also Tango not support this type immo and can not reset 128bit keys
Page 1 A8, A9, 88, 38, F1

Sent from my C5502 using Tapatalk

[rob h]

If i would write a virgin dump in to the smartbox.
Then i can add keys, but have to synch to steeringlock, and ecu.

I you add keys to my dump, i will keep the synch?

Will techstream V.10.30.029 help me to synch steering lock?

I am hoping to upgrade to V.11.10.039 soon.
But i do not know if it covers the new Aygo (KGB40).

I found the partnumber for these smartkeys now, 89904-0H010

These are the tools i now have, techstream Tango, and skp900.

[Siham]

[QUOTE=Brayn;2788858]That's why I said Tango can't do this. Siyadk correct. Also Tango not support this type immo and can not reset 128bit keys
Page 1 A8, A9, 88, 38, F1

Did you tested DST 128 reset fonction on Tango ?
Because they claim that with their new update they can do it and also TM100 seam to be ok in this fonction .

Thank you Dude :)

[Brayn]

If i would write a virgin dump in to the smartbox.
Then i can add keys, but have to synch to steeringlock, and ecu.

I you add keys to my dump, i will keep the synch?

Will techstream V.10.30.029 help me to synch steering lock?

I am hoping to upgrade to V.11.10.039 soon.
But i do not know if it covers the new Aygo (KGB40).

I found the partnumber for these smartkeys now, 89904-0H010

These are the tools i now have, techstream Tango, and skp900.
If you reset smart ecu, you can add keys and no need to synchronise system.
Techstream any version can do that.


Sent from my C5502 using Tapatalk

[rob h]

We should be able to reset H smart keys with Tango.
•Reset of Toyota/Lexus/Subaru Smart Keys 40, 80, 128 bit*
As far as i know, you can only reset the smartbox, if you have a working master key.
Or a smart system without id box, like some US market Toyotas.
And making the smartbox virgin by dump, is for all keys lost situations.

[siyadk]

Did you tested DST 128 reset fonction on Tango ?
Because they claim that with their new update they can do it and also TM100 seam to be ok in this fonction .

Thank you Dude :)

Tango and tm100 can reset used DST 128 keys . Both Tested!! where do you think tm100 engineers cracked DSt128 reset code:playful:. of course from our poor tango.Fly managed to crack within a day after tango released their DST128 unlocking update and started selling them like hot cakes

[siyadk]

If i would write a virgin dump in to the smartbox.
Then i can add keys, but have to synch to steeringlock, and ecu.

I you add keys to my dump, i will keep the synch?

Will techstream V.10.30.029 help me to synch steering lock?

I am hoping to upgrade to V.11.10.039 soon.
But i do not know if it covers the new Aygo (KGB40).

I found the partnumber for these smartkeys now, 89904-0H010

These are the tools i now have, techstream Tango, and skp900.

A lot of confusion going on, so let me keep this simple as possible

you have three options ( in most of toyota smart systems)

1. Adding keys to Dump manually:-post smart box dump and key data. Once you get new dump with key added, you will get ign on and can program the new keys in. You will not lose any sync codes. however this requires new(aka virgin) key. if you have used key, of course you can reset it with tango, tm100, mk3 and now with vvdi2 to make it virgin all over again and add like a new key. this option doesn't require to pull id code box which saves a lot of time, money and labour. For me typically takes 10 to 15 mins max


2. RESETTING DUMPS:-Resetting smart box and id code box dumps,post dumps here, most of them here in dk can reset the dumps. this again will not lose any sync and can program even an used key to it. However disadvantage to this option is to get id code box which is very hard to get and mostly half a day job. A lot of waste time and labour

3. VIRGINISING Dumps or "New smart box and Id code box" from dealer : Virginising smart box and id code dumps, again used key can be used and need to sync id code box to ECU by short 4 and 13. ESL will sync automatically.However getting virgin dumps are hard or else you need buy both ecu from dealer, therefore i dont prefer this method because this needs a lot of labour again to pull id code box and money if need to buy new ecu from dealer or time and patience to keep hunting for virgin dumps

[Siham]

Tango and tm100 can reset used DST 128 keys . Both Tested!! where do you think tm100 engineers cracked DSt128 reset code:playful:. of course from our poor tango.Fly managed to crack within a day after tango released their DST128 unlocking update and started selling them like hot cakes

Dear Mate , you right Fly cracked it tango as they cracked AVDI ,but AVDI did cloning improvments so why Scorpio did not or if they did they did it badly . :)
Only think they wasn't able is to add image generator for DST and g chips ,but is only a matter of time and Fly will make a new update. :)

Best regards :)

[siyadk]

YES.. but a point to be noted here. Tm100 hasn't implemented all modules which tango released lately( for ex: image generator for toyota DST+ key, couple of ford modules). Tm100 released toyota key reset key because they knew this was golden egg for them and can be monetized easily. In other words, additional revenue from their existing tm100 clients base and bit more appealing product for new clients to buy

so it makes me wonder lately with tm100, they are releasing updates which can be quickly made to cash. It seems they turn backs current bugs which tm100 has for example: the transponder reading/writing speed which more than a min for normal 4d transponder

To make things worse; they have very bad customer support. I have sent many humble request to fly pointing out bugs which could be fixed easily. however they never seems to listen. Gone were the days where Gwee could stand up, put pressure and bargain for us to fly engineers and management to fix bugs we faced

[Brayn]

i use Russian tool for toyota smart key reset and program

https://www.youtube.com/watch?v=7eazJDv65GA

[SMARTBOY]

Hi

This is Camry 2015 smart H key

i don't find chip which one i have to read

please masters advise

[usman4]

solved.....

[SMARTBOY]

if you asking me then NO

[Brayn]

Send me your smart ecu part number

Sent from my C5502 using Tapatalk

[MattLock]

That is the same smart ecu as the Kluger/Hilander
Not all key data is stored on the smart ecu
some on smart ecu some on electronic steering lock and some on code id box
all have to be replaced with virgin and coded with tech stream as far as I'm aware atm

[SMARTBOY]

Send me your smart ecu part number

Sent from my C5502 using Tapatalk

Smart box aded

[Mr_Fix]

IC003 must be EEPROM - 93C86

[Brayn]

Yes your right Mr_Fix that should be eeprom location
I think someone remove that

Sent from my C5502 using Tapatalk

[Mr_Fix]

Yes your right Mr_Fix that should be eeprom location
I think someone remove that

Why to confirm obvious?

[Tagne]

382151 hello mate please i need reset or virgin files for this camry ecu H KEY thx you i attach dump of smart ecu

[cjawahir]

382151 hello mate please i need reset or virgin files for this camry ecu H KEY thx you i attach dump of smart ecu

here try this let me know how it goes .

:)
cj

[Tagne]

here try this let me know how it goes .

:)
cjthx you master i write your reset file keys shows 0 but when i touch smart key to the push butin it gives error . thx for those that can give another files

[cjawahir]

thx you master i write your reset file keys shows 0 but when i touch smart key to the push butin it gives error . thx for those that can give another files

post key data , like dst +

cj

[siyadk]

thx you master i write your reset file keys shows 0 but when i touch smart key to the push butin it gives error . thx for those that can give another files


without reseting id code box, how are you going to add key?

your best option, like CJ said, add key to dump

read this post
http://www.digital-kaos.co.uk/forums/showthread.php/406865-***Toyota-Smart-Lost-Key-Solution-No-Id-code-needed***?p=2789665&viewfull=1#post2789665

[Tagne]

post key data , like dst +

cjthx you this key data


382228

[siyadk]

H smart key added on dump

[Tagne]

H smart key added on dump

thanks for added me key but unfortunately only ignition gets on when i put smart key near to push button but not star. please i need another file thx you

[siyadk]

my bad..a small typo error. did theprevious file in a hurry
this file should work

[rob h]

synch steeringlock and ecu with techstream.

[aketokediag]

my bad..a small typo error. did theprevious file in a hurry
this file should work

You are doing great job friend, please keep it up...

[Tagne]

my bad..a small typo error. did theprevious file in a hurry
this file should work
thx you very much M8 but that car still not start :mad-new:

[cjawahir]

thx you very much M8 but that car still not start :mad-new:


post the id code box , if can reset u can add key via obd .

cj

[siyadk]

post the id code box , if can reset u can add key via obd .

cj

You getting ignition on? what does security light do?
Double checked the dump i posted and it has key added in it perfectly
or else like CJ suggested get id code box

[Tagne]

You getting ignition on? what does security light do?
Double checked the dump i posted and it has key added in it perfectly
or else like CJ suggested get id code box

yes security light go off ; steering lock is free thx for you effort masters; this is ID CODE
382743

[cjawahir]

yes security light go off ; steering lock is free thx for you effort masters; this is ID CODE
382743

does the steering unlock with the key , and then lock back after ignition off ?
does the vehicle crank?
did you scan the vehicle for fault code ?


cj

[Tagne]

does the steering unlock with the key , and then lock back after ignition off ?
does the vehicle crank?
did you scan the vehicle for fault code ?
cj
no it doesnt go off
no vehicle no crank
yes i scan no dtc stored

[siyadk]

1. Check brake switch
2. Check gear in P
3. Check ign1 n ign2 relay in main body ecu
4. Check whether you are getting green light in start stop button
5. Sreerling lock like cj said
Security off means key is fine. Most probabaly some other issue preventing car to start

Sent from my SM-G935F using Tapatalk

[mra999]

Good Job Siyadk

[SMARTBOY]

IC003 must be EEPROM - 93C86

MR FIX ,You are right i did not found ic 93c86 i think missing but when i have fix the ic with working dump no more ignition and i am more confused
what i did i have take off full dash then i try to find The ID code Box , where should be ID Code Box there i dont find out id code Box
Now i am Big confused and here is VIN 6T1BF9FK5K5EX492172

[SMARTBOY]

Yes your right Mr_Fix that should be eeprom location
I think someone remove that

Sent from my C5502 using Tapatalk
MR FIX ,You are right i did not found ic 93c86 i think missing but when i have fix the ic with working dump no more ignition and i am more confused
what i did i have take off full dash then i try to find The ID code Box , where should be ID Code Box there i dont find out id code Box
Now i am Big confused and here is VIN 6T1BF9FK5K5EX492172

[Tagne]

does the steering unlock with the key , and then lock back after ignition off ?
does the vehicle crank?
did you scan the vehicle for fault code ?


cj

thanks for all details and i checked that when i pressed brake pedal there's no green light on push button now tell me what's the problem of starting and how can i solve it

[Tagne]

1. Check brake switch
2. Check gear in P
3. Check ign1 n ign2 relay in main body ecu
4. Check whether you are getting green light in start stop button
5. Sreerling lock like cj said
Security off means key is fine. Most probabaly some other issue preventing car to start


Sent from my SM-G935F using Tapatalk
thanks for all details and i checked that when i pressed brake pedal there's no green light on push button now tell me what's the problem of starting and how can i solve it

[mra999]

You can try this
Write Files

[Tagne]

thx you everybody i cloned id box n smart ecu ; virgin smart keys n add key from the same working car
car STARTED FINE :thrasher::thrasher::thrasher::rock::rock::rock:

[ngakson2002]

Hello Mate,

Please need help in having the Page 1, 2, 3 and 4 Transponder data from the dump attached which is from the ECU AGGREGATION box of a 2006 TOYOTA VITZ with all smart keys lost.


All the Best

[cjawahir]

Hello Mate,

Please need help in having the Page 1, 2, 3 and 4 Transponder data from the dump attached which is from the ECU AGGREGATION box of a 2006 TOYOTA VITZ with all smart keys lost.




All the Best

OK i send u pages to write to tpx2 chip , u can start vehicle . let me know how it goes

cj

[irwin88]

Hi Sir,

I encounter this Toyota Camry with all key lost. Can anyone help to virginise the Smart Key Module and ECU ID Code box.

Also appreciate if anyone can prepare Page 1 - 4, transponder data to write key, temporarily to start the car.

Appreciate if you can help, and thanks in advance

[aketokediag]

You will not get ignition just register the key with your techstream or X-100 and follow this proccess try and perform syncronize between the ECU and IMMO open driver's door, turn ignition ON short terminals Tc (PIN13) CG(PIN5)in the DLC/OBDII connector leave it for 45minutes the car should start.
Regards

[Tagne]

hello mate please i need help to program me this smart key data inside this smart dump car is toyota pruis 2010; i attach dump n keys data
thx you in advanced
KEY DATA
pg1 98
pg2 E3
pg3 20 A7 55 1D
pg8 98 31 5D 92 30

[neverquiet]

It is possible for a RAV4 2013 smart key ecu designed to work without a ID Box?
384522
The ID Box is no where to be found?
It's South America Version.
BR.

[Tagne]

hello mate please i need help to program me this smart key data inside this smart dump car is toyota pruis 2010; i attach dump n keys data
thx you in advanced
KEY DATA
pg1 98
pg2 E3
pg3 20 A7 55 1D
pg8 98 31 5D 92 30
hello master please really need help; thx you in advanced

[PremierD]

Give that a birl mate ...

[usman4]

Hello Masters.. Here's Aqua all lost smart keys, someone tried and unfortunately erase its smart dump. now i have original smart dump from another Aqua, is it possible to add key in dump and start the car??
Here's virgin smart key data
pg1 = 98
pg2 = C9
pg3 = E5 22 01 1C
pg8 = 98 31 30 5E 96

[aketokediag]

Is possible to write key to another smart dump and start the car only the remote will not work
Regards

[aketokediag]

@ irwin88. It cost you $0.00 to say thank you, no update, no thanks, no help. Good day
Regards

[PremierD]

Hello Masters.. Here's Aqua all lost smart keys, someone tried and unfortunately erase its smart dump. now i have original smart dump from another Aqua, is it possible to add key in dump and start the car??
Here's virgin smart key data
pg1 = 98
pg2 = C9
pg3 = E5 22 01 1C
pg8 = 98 31 30 5E 96


Try that ... and report one way or the other ..

[usman4]

thanks bro.. but only ignition gets on, no start

[Tagne]

Give that a birl mate ...
milion thx big master car started few minute ago. have nice day

[siyadk]

thanks bro.. but only ignition gets on, no start

this should work..pass in pm

[usman4]

thanks bro but same condition.. only ignition gets on near to the push button but vehicle not started, i tried DLC 4,13 but not started

[usman4]

really thanks PremierD and Siyadk for your generous help but may be the problem of the dump of another vehicle. now i have to remove id code and then program smart keys. the only working solution i ever have :D

[usman4]

Thank u guys.. vehicle started with removing dash and reset id code and smart ecu, program smart keys.. thanks

[aketokediag]

Am happy for you USA MAN, enjoy your ride

[usman4]

thanks brother :)

[lylezim]

can someone please help to add key to this dump386371

[ibratex]

hello , mates will the remote work also if i used this method on this thread posting 93c86 ? it is prado 1kd-ftv 04.2014

[Brayn]

Am happy for you USA MAN, enjoy your ride

my friend he is not USA MAN he name is Usman :)

[usman4]

ha ha ha Thanks bro :P

[Brayn]

Hello Dk masters
Toyota 2014 Voxy Hybrid 128bit-AES
This vehicle smart ecu have 93c66. But smart key data not in this eeprom (93c66) key data have NEC prosecer also it have a lock 🔐. I have ask some Friends they told me when all keys lost situation should replace Smart ecu
We can't reset / virgin smart ecu and programme keys.
Any body have experience with this Toyota new system?

Sent from my C5502 using Tapatalk

[ucokseparoh]

Hi friends.. if it's a deal this would be my first experience dealing with a smart key. I was just phoned to make a spare for Corolla Altis 2008 (automatic transmission).

Will anyone here point me out to the right direction so i can make a spare for this key please..

I have Tango with Toyota Key Maked loaded in and an X100Pro. Just checked X100Pro there is an option for smart key,just don't know which type should i choose for this job (1,2 or 3?)

Should i order a smart key from dealer or getting it from HKlock is enough?

Please shed me some light on what should i do for this job..

Thanks for any help..

Best regards..

[Brayn]

Hi friends.. if it's a deal this would be my first experience dealing with a smart key. I was just phoned to make a spare for Corolla Altis 2008 (automatic transmission).

Will anyone here point me out to the right direction so i can make a spare for this key please..

I have Tango with Toyota Key Maked loaded in and an X100Pro. Just checked X100Pro there is an option for smart key,just don't know which type should i choose for this job (1,2 or 3?)

Should i order a smart key from dealer or getting it from HKlock is enough?

Please shed me some light on what should i do for this job..

Thanks for any help..

Best regards..
1. If you use x100pro you should silect 1
2. If you buy key from dealer it is very easy to programme key
3. If you buy used smart key, you can programme it also
4. If you buy used key you can programme it aftet reset smart ecu or you can virgin that key using Tango or any other tool ( should have Toyota smart key reset function)
5. If you virgin / unlock smart key you can programme key via obd port just like a brandnew key.


Sent from my C5502 using Tapatalk

[ucokseparoh]

1. If you use x100pro you should silect 1
2. If you buy key from dealer it is very easy to programme key
3. If you buy used smart key, you can programme it also
4. If you buy used key you can programme it aftet reset smart ecu or you can virgin that key using Tango or any other tool ( should have Toyota smart key reset function)
5. If you virgin / unlock smart key you can programme key via obd port just like a brandnew key.


Sent from my C5502 using Tapatalk


Hi Brayn,many thanks mate for your valuable input.

I've seen here in this thread if ordering a brand new smart key from dealer,it is done by vin number. In case i want to buy a used one,do you have any tips for this Brayn? what things should i look closely when buying a used smart key (things like Pg1,frequency..etc?).

Best regards.

[aketokediag]

Hello M8,
If you are buying the key through dealer is not most to make use of chassis number take not of original key frequency and Pg type, if you are to buy used type no problem both will work the car, all you need to do is to read the the master key that start the car with your Tango also read used key to confirm if both are same Pg and frequency type.
Good luck
Regards

[ucokseparoh]

Hi @aketokediag.

thanks mate for your valuable insight.. i really appreciate that mate.

[aketokediag]

You are always welcome.

Sent from my Infinix X506 using Tapatalk

[makura]

Hi
I need smart entry box reset solution without ID box for smart box number 89990-52260.
Regards

[Brayn]

Hi
I need smart entry box reset solution without ID box for smart box number 89990-52260.
Regards

for what you want reset only smart ecu?
1. for add used smart key?
2. All lost key situation?
3. replace smart ecu?

or any other?

if you tell what is your problem can help you

[makura]

Hi
All keys are lost for this car.
thanks.

[makura]

for what you want reset only smart ecu?
1. for add used smart key?
2. All lost key situation?
3. replace smart ecu?

or any other?

if you tell what is your problem can help you
Thanks for the questions m8,got my hopes high thinking i am getting a solution only for you to go silent,guess if i had said i wanted to replace smart box you would have told me to swap eeprom,right?

[Brayn]

Hi
All keys are lost for this car.
thanks.
If all lost key,
1. You can make master key to smart ecu dump using Tango, MKIII, TM100, FVDI, TLSprog, iprog like that tool and start vehicle

2. you have to reset Smart ecu and id code box
After you can programme keys using t300, X100, techstream or any sutable key programmer

3. All lost key job can not do reset only smart ecu

Sent from my C5502 using Tapatalk

[makura]

If all lost key,
1. You can make master key to smart ecu dump using Tango, MKIII, TM100, FVDI, TLSprog, iprog like that tool and start vehicle

2. you have to reset Smart ecu and id code box
After you can programme keys using t300, X100, techstream or any sutable key programmer

3. All lost key job can not do reset only smart ecu

Sent from my C5502 using Tapatalk
Thanks m8 but thats the same old way of doing it,the title of this thread says SMART LOST KEY SOLUTION NO ID CODE NEEDED right? That is why i posted here,i have seen some posts were people got a reset that works without ID box dump.
Thanks any way.

[Brayn]

......[emoji2]

Sent from my C5502 using Tapatalk

[Brayn]

Thanks m8 but thats the same old way of doing it,the title of this thread says SMART LOST KEY SOLUTION NO ID CODE NEEDED right? That is why i posted here,i have seen some posts were people got a reset that works without ID box dump.
Thanks any way.
Yes can do
1. You should post key data and smart ecu data after can key data add to smart ecu and start vehicle
2. You have tool Tango, TM100, MK3, iprog like that tool you can do it yourself
No need to remove Id code box.

If you can post key data to then dk friend will help you
Unfortunately I can not add key data to smart dump

I can help you reset smart ecu and id code box.
Usually I do remove smart ecu and make master key to smart dump vehicle start within 10minuits

Sent from my C5502 using Tapatalk

[makura]

Hi
I have tried to make master key to dump with my original AVDI but its not working at all,it works on other smart boxes but it wont work with this one.
With tango i am getting ignition on and the car just cranks and wont fire up.
This car just lost the keys and it was running fine so i think its all in the programming and nothing else.

[PremierD]

Your Dump looks very strange .. lots of dublicate data ...

[ivannzowa]

hello,someone help me to renew idcode and ecu aggregation for toyota rav 4,attached is both dumps

[mahmoudsaq]

hello
please i need help to program me this smart key data inside this smart dump car is toyota land cruiser

KEY USED DATA
pg1 98
pg2 96
pg3 63 72 5D 1C
pg8 98 2B 07 16 D6

392066

BEST REGARDS

[makura]

[QUOTE=Brayn;2825081]If all lost key,
1. You can make master key to smart ecu dump using Tango, MKIII, TM100, FVDI, TLSprog, iprog like that tool and start vehicle

2. you have to reset Smart ecu and id code box
After you can programme keys using t300, X100, techstream or any sutable key programmer

3. All lost key job can not do reset only smart ecu

Sent from my C5502 using Tapatalk[/QUOTE
Hi
I have searched my Vits,stripped it to bits and i cant find no ID box any way.
Any ideas?

[aketokediag]

Why can't you reset the smart and id code box

Sent from my Infinix X506 using Tapatalk

[makura]

Why can't you reset the smart and id code box

Sent from my Infinix X506 using Tapatalk
Well i cant reset ID box because its not there.

[Frankcar]

anyone can help me for adding a key on this file ?
is250 2009

pg1: 98
pg2: B3
pg3: B72B1B2A
pg8: 98310B3D48

[aketokediag]

I can only reset for you and you add key with your diagnostics tool.
If you want that let me know.

Sent from my Infinix X506 using Tapatalk

[makura]

Please rest my set of dumps.
Regards

[aketokediag]

Please provide your id code dump and i reset for you.
Regards

[ucokseparoh]

Why can't you reset the smart and id code box

Hi mate.. how do you reset them? Did you do it manually or with some spesific tools/soft? As far as i know only one with AVDI can do it.. i may be wrong. Please give us advice mate..

thanks in advanced. Best regard mate..

[makura]

Please provide your id code dump and i reset for you.
Regards
No ID box on this car,just the steering lock and smart key ecu 89990-52260 steering lock 45020-05-3

[usman4]

here u go......

[makura]

here u go......
Thanks m8 but the reset is not working,it starts key learning ok but cuts it out after 2 seconds before i can touch the start button with the key the buzzer starts buzzing.

[usman4]

bro there's no doubt on my files.. its better to post here more details like which tool u used and what was the procedure u did to program smart key.

[makura]

bro there's no doubt on my files.. its better to post here more details like which tool u used and what was the procedure u did to program smart key.
Hi
I used abritus and it failed then i used techtream with the same results.
Connected the diagnostic machines,started the key programming procedure then it tells me to touch the start button with the new key with the emblem side facing the button,before i can do that the buzzer starts beeping and touching the key to button has no effect or responce.
Both programmers have the same error

[usman4]

I think u first time registering smart keys.. bro bro bro reset files don't gives u ignition on so how can u use techstream?? Techstream perfectly works with ignition on. Use my reset files and use any obd programmer like skp900,x100 pro, t300 to register smart key, doesn't matter its new or used.

[makura]

I think u first time registering smart keys.. bro bro bro reset files don't gives u ignition on so how can u use techstream?? Techstream perfectly works with ignition on. Use my reset files and use any obd programmer like skp900,x100 pro, t300 to register smart key, doesn't matter its new or used.
I am not getting ignition on bro,when i connect techstream i get an option that says key registration on the car selection and key programming procedure starts.I have done several smart keys but not the one with no id code unit.
I could be doing something wrong,i will try with x100 in the morn and report back.

[usman4]

Yes its better to be try with x100 and report..

[zippy82]

Hi can anyone reset these dumps? It's not the normal eprom as it's a 95160

393070393071

[akbarkeys]

Please help,,,,!!!! all key lost toyita passo 2004...
Toyota passo, thn 2005, No vin QNC100014894 and mechine K31272252,and i need your help....

[makura]

Yes its better to be try with x100 and report..
Not working for me,X100 wont communicate with unit after the reset dump,but with original dump i get options to reset immo etc.

[aketokediag]

Mate what is the problem? What brand of vehicle are you working on? Will try n help u.

Sent from my Infinix X506 using Tapatalk

[makura]

Mate what is the problem? What brand of vehicle are you working on? Will try n help u.

Sent from my Infinix X506 using Tapatalk
Its a 2011 Toyota Vitz,no ID box on this model.All keys lost,AVDI cant do master key on this either,but with tango i can do master key and get ignition on,but the car wont start but just crank and wont accept adding a key that i got from the stealer.

[usman4]

bro then find your fault.. my files are 100% correct

[usman4]

Solved..........

[PremierD]

Data inserted looks fine to me ...
apart from it having 4 keys on one location and 2 in the other :)

[usman4]

I repaired dump and then make master key and vehicle started. :)

[lioncam]

Hi,
please i need frequency for this toyota,
vin: 2T3DK4DV7AW026780,
try to program key with 433 mhz without succes.
thks.

[cjawahir]

Hi,
please i need frequency for this toyota,
vin: 2T3DK4DV7AW026780,
try to program key with 433 mhz without succes.
thks.


315mhz , this vehicle is LHD ?

cj

[rob h]

Tango came out with a new upate: I do not know what types it coverers.
Probable G-chip and before.

First in the World:Dump editor to pair Smartkey ECU with ID CODE ECU.
True calculation of synchro code on Smartkey ECU.
Dump editor pairs all four units:
Engine ECU, Smartkey ECU, Steering Lock ECU and ID CODE ECU

Not so long ago,they released a g-chip all keys lost by obd, for european cars.

[abvayani]

I try to find that Option in Tango pairing smart Key ECU and ID Code.
But im not Success.
Can i have to active softwear.

Sent from my SM-J700F using Tapatalk

[offys]

Hello DK member

Thanks for goods information for sharing i need to renew ID code and Certificate ECU on My Lexus is250 swap engine to be ISF (2ur-gse)

[vitzauto]

can so one reset the file for me it's landcrusier vdj200

Sent from my SM-G935F using Tapatalk

[vitzauto]

ls some one reset this smart box file for me.
thanks\396854

[usman4]

here u go..............

[vitzauto]

usman can u check the file again it's blank

Sent from my SM-G935F using Tapatalk

[usman4]

Impossible mate u can check it again :)

[vitzauto]

ok I will check and report

Sent from my SM-G935F using Tapatalk

[aketokediag]

hello,someone help me to renew idcode and ecu aggregation for toyota rav 4,attached is both dumps


Hello m8,
Have you solve your problem, let me know please.
Regards

[teamimpresiv]

need help with coding of Toyota Rav4 keyless, i have attached the 93c86 dump and 2 key data, any key will do, thanks397492397493397494