Chineese Galletto V54

[minimex]

Hi.
I know that ktag copes with it, I use it.

But back to the question of galletto, where it can be probrem:
hardware, firmware whether software.

How performs the Galletto EU?

[electronistul21]

galletto EU ist good device.i think you know better,because ist make in your contry

[carmageddon]

galletto eu have ONLY pcb better, nothing else!

v53_0475 china hw-sw upgraded is better

[art64]

Hello, I can't read EDC15P+ via k line on the bench(Galet. V54).Me did try on 2 different ECUs. How to the other owners of Galeto V54? Does this funtion works?

[tango]

Hello, I can't read EDC15P+ via k line on the bench(Galet. V54).Me did try on 2 different ECUs. How to the other owners of Galeto V54? Does this funtion works?

is it reworked ?
if no then there is your problem as people with reworked gallettos have no problems with edc15p+ etc if you read through most galletto threads you will see

[art64]

Sorry, I'm the beginner in this. What means 'reworked'? Me suposse it is upgraded device by the Fantomel schema, yes? Does it will be good in all modes (obd,bdm..)? Mine works fine in bdm mode and me don't want to loose it. Maybe cheaper way is to buy the other device (some like mpps) and fgtech V54 to keep for works in bdm? It seems for the reworks also necessary to buy someone device and spend some time

[morphvale]

Hello again lads, got a quick question for you.
Anyone that has read a 2005 Ford Focus 2 EDC16C34-2 by OBD? How long does it take? I've read and wrote mine a few times now, but reading takes about 20 minutes, while writing takes about 10 minutes (both CAN, no option to select Kline for this ECU on Ford).
While that is fine, this weekend I used the tool on two of my friends cars (a '03 Passat with EDC15CP - 512Kb read and a 05 A4, with EDC16U31 - 2MB read) and both took about 2 minutes to complete reading by Kline. Did not try a write.
Is that the normal time for the Focus's EDC16C34?

[wiski]

you got full file that's why

Sent from my SM-A510F using Tapatalk

[morphvale]

Shouldn't all 3 files be full read? I didn't see any option of doing a partial or full read, and all 3 files seem to have correct size.

[lupu_sandu]

On Audi EDC16CP34 takes 15 minutes to read only maps, so time is relative mate!

On other hands:
Seems that my G54 suddenly stop writing Renesas ECU. Read OK, cannot write. I don't know why.
Few months back i read/write few Nissan,Mazda ECU but now cannot write.
Cable is ok, connection are ok because if i change only galletto can write.
Mine is china G54 reworked. Is not that big deal, still have another that work, also Ktag, but still bugs me.

[art64]

Why for in green color marked wire named 'igniction'? Is it mistake? This pin in OBD is known as k line. I did test on this pin in my Galletto and find +12V. Is it normal?

[carmageddon]

if you use boot st or obd protocols green are K line whilst if you use boot mode tricore green are 12v, the relais make exchange for this function

[dadal]

I want to also change resonator with this one,,,but my galettos resonator has 3 legs,,,can I use it ?

373830

[carmageddon]

desold resonator, clean central hole, place a piece of ribbon or paper on central hole, resold up the quartz.

[dadal]

Thank you Carmageddon :shakehands:

[bobolin4o]

What improvements we can expect from this modification (resonator vs quartz)?

[spychu14]

Nice - shiny look :)
In original there is resonator but it works fine with quartz too. In my opinion there is no difference but always is good to change china parts to original ones :)

[carmageddon]

What improvements we can expect from this modification (resonator vs quartz)?

precision and constancy of clock!

have you never heard of resonator watch? i think not, only quartz watch

[bobolin4o]

Hm... my FG is with resonator and AROMAT relays, and for now i never had an issue with anything, which is in the car list, BDM or whatever.
Firstly i had use software from china disc on win7, which are "very unstable", without any troubles... then i decided to reflash with software for tool 0475, and now my FG work without any difference, exept that sometimes won't start and give me a message for Visual C+ blabla...

[bobolin4o]

Nice - shiny look :)
In original there is resonator but it works fine with quartz too. In my opinion there is no difference but always is good to change china parts to original ones :)

What mean "original parts"... they are produced in china too... in the best case - in Taiwan.
No big difference for me...
:)

[mircea13]

original ones means the real deal component not some 2 cent chinesse counterfeit. we all know that 90% of the electronic components are made in china or taiwan but they are made by some reputable industries , not by a bunch of chinesse teenagers in a shed, like the one used in these clones.

[bobolin4o]

original ones means the real deal component not some 2 cent chinesse counterfeit. we all know that 90% of the electronic components are made in china or taiwan but they are made by some reputable industries , not by a bunch of chinesse teenagers in a shed, like the one used in these clones.

You may think so, if that makes you more relaxed...
Read again my post - i have FG54, with only changed LS14 chips - work perfect with low cost china components, made "by a bunch of chinese teenagers in a shed"
Regards!

[mircea13]

374623are those 7 capacitor 10uF 50v? cause the first 4 from the bottom of the bord in my clone where 10uF 50v and other 3 from the top where 100uF 50. is 10uF 50v correct for all 7 capacitors?

[carmageddon]

c21-c26-c28 = 100uF 50V

the other 7 capacitor are 10uF 50V

[mircea13]

thanks camrmageddon! can you tell after hw reowork what software is good and stable for this 0386 tool? I'm using now the AES software.

[carmageddon]

v54 eu-china are old 6 month...v53_0475 is the best for fg clone!

[mircea13]

so i have to write lpc with the hex for 0475?

[carmageddon]

the best thing is rewrite lpc

[kakaruki]

hi is there somebody who do rework service on china fg tech v54 pcb to make it working good?
i can ship it to you then...

[mircea13]

and how can be done? i mean to upgrade my 0386 to 0475 i have to rewrite the lpc with the 0475 hex mcu and ept file for 0475? can someone explain in detail how can this be done "?

[massimo1974]

and how can be done? i mean to upgrade my 0386 to 0475 i have to rewrite the lpc with the 0475 hex mcu and ept file for 0475? can someone explain in detail how can this be done "?


http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386?highlight=fgtech

[mircea13]

today my galletto v54 went dead . k-line dosent work can dosent work bdm i didn't try it but it wont.is says error send wake . it worked fine until today and now is dead . what should i do ? what component are for kline and can ? l9613 ?

[proel]

I have strange issue with psa edc16c34 k-line writing over obd2 in car. I get "error format" message... I try read/write same ecu MPC561 on bench over obd2 k-line and all is ok. Could be problem with soft (I use v54 soft). EDC16c34 ecu's with CAN work fine over obd2 in car. I have all hw mod's except 2 zvn/zvp transistors (my version is with 2 x ZVP2601a). Someone has already tried to replace Q20 with 2N7000 , Q18 stay ZVP2601a ? Can somebody write d/l link for good v53 ver...

[kospoz]

I have v54 with strange error on bdm.I have read one edc16u34 and when i tried to write the file back i had error micro not supported also the software showed the bar after a good write (dashboard off for 10 seconds).after that i can not connect with the ecu.Car starts so ecu is fine but what is wrong with galletto?

[toms4]

I have strange issue with psa edc16c34 k-line writing over obd2 in car. I get "error format" message... I try read/write same ecu MPC561 on bench over obd2 k-line and all is ok. Could be problem with soft (I use v54 soft). EDC16c34 ecu's with CAN work fine over obd2 in car. I have all hw mod's except 2 zvn/zvp transistors (my version is with 2 x ZVP2601a). Someone has already tried to replace Q20 with 2N7000 , Q18 stay ZVP2601a ? Can somebody write d/l link for good v53 ver...
Not all ecus (car) have K-line pin from ecu connector to OBD connector. Did you checked, your car EDC16C34 have?
I have replaced Q20 with 2N7000.

[proel]

Not all ecus (car) have K-line pin from ecu connector to OBD connector. Did you checked, your car EDC16C34 have?
I have replaced Q20 with 2N7000.

If I can read over k-line in the car there is no reason not to write. I have used old v48 and never had problems with this ecu. I ordered the original zvn transistor and wait to come.

[jokerrro]

Hello
Gentlemen LOW Voltage, galletto worked and suddenly a number.
The device version 475 after replacing circuits and relays.
Windows sees the device but the voltage is not and can not use the equipment

[PartyTwist]

Hi,

I'm trying to repair my Galletto to work with Mitsubishi Boot but I'm missing a component that's not visible on the pictures. Can someone lend me a hand?
It's a SMD resistor (I presume) on the lower right part of the picture, between .3F and 295.

http://i.imgur.com/CBki6l2.jpg

Any help or pointers would be greatly appreciated.


EDIT: I mesured it wrong. it goes directly to the .3F So I have something else wrong :/ Anyone got mitsubishi boot protocol working? I have changed HC* stuff, relays,...

[lipart25]

I can not start it you can explain how to do?

[Alfik]

What is transistors Q18,Q20? On my PCB they are not that is installed.
What will not me work?

[leverage454]

v54 china clone works good but it had a problem trying to read a pcr2.1 after unlock and kess v2 clone did the work perfectly so i think you will need both of them

[svvag2000]

Hi, everybody.
Near the resonator I have two different condensers. Differ in color

What there has to stand? 22pF???

389432

[jsg1200]

Hi,

I'm trying to repair my Galletto to work with Mitsubishi Boot but I'm missing a component that's not visible on the pictures. Can someone lend me a hand?
It's a SMD resistor (I presume) on the lower right part of the picture, between .3F and 295.

http://i.imgur.com/CBki6l2.jpg

Any help or pointers would be greatly appreciated.


EDIT: I mesured it wrong. it goes directly to the .3F So I have something else wrong :/ Anyone got mitsubishi boot protocol working? I have changed HC* stuff, relays,...

I think that this It is a resistor 222, but I dont have this component...

[toms4]

Hi, everybody.
Near the resonator I have two different condensers. Differ in color

What there has to stand? 22pF???

389432


These can be 18-22 pF

[antotechaustin]

Anyone have the clean software V54? The software that came with my Galletto has a virus.

[jakesman]

I have strange issue with psa edc16c34 k-line writing over obd2 in car. I get "error format" message... I try read/write same ecu MPC561 on bench over obd2 k-line and all is ok. Could be problem with soft (I use v54 soft). EDC16c34 ecu's with CAN work fine over obd2 in car. I have all hw mod's except 2 zvn/zvp transistors (my version is with 2 x ZVP2601a). Someone has already tried to replace Q20 with 2N7000 , Q18 stay ZVP2601a ? Can somebody write d/l link for good v53 ver...


i also have 2 same transistors and replaced Q20 with 2n7000 and wooopy now BDM do not work anymore swaped it back , i will wait for the real component to arrive

[speedy100]

Hello,
Does anyone have any comments about this clone as i am thinking of buying it?
http://www.carsets.co.uk/wholesale/vd300-fgtech-galletto-master-bdm.html



(http://www.carsets.co.uk/wholesale/vd300-fgtech-galletto-master-bdm.html)

[carmageddon]

useless version of tool!

dont buy it

[speedy100]

useless version of tool!

dont buy it

What about this:
http://www.carsets.co.uk/wholesale/latest-fgtech-galletto-4-master-bdm-obd-function.html

Or any suggestions please for a working clone?

Thanks :)

[azibi130]

mine arrived yesterday.
here's some pics....

395975

i have one question, can i use an external power supply of 13.8v 3A constant, instead of the chinese power supply of 12v 1A?or it will burn my fg tech?

today will try to read/write by k-line, bench and on car and report...
next week will try bdm function...

[kospoz]

mine arrived yesterday.
here's some pics....

395975

i have one question, can i use an external power supply of 13.8v 3A constant, instead of the chinese power supply of 12v 1A?or it will burn my fg tech?

today will try to read/write by k-line, bench and on car and report...
next week will try bdm function...
I always use car battery without any problem

[speedy100]

What about this:
http://www.carsets.co.uk/wholesale/latest-fgtech-galletto-4-master-bdm-obd-function.html

Or any suggestions please for a working clone?

Thanks :)


Anything for me???

[azibi130]

I always use car battery without any problem

thank's for reply, but does anyone use an external power supply like the onei have?

[azibi130]

Anything for me???

you answer is in this topic mate.
there are 3 diff hardware pcbs. ppl in topic said some work some functions, others work all, can't say much because i haven't tried mine yet...

[speedy100]

Anything for me???

I have downloaded from this link that i found while reading this thread as the european version of software but my Avast finds three infected files. See pic....

http://uploaded.net/file/2ann5mny

396021

Best Regards

[azibi130]

it's normal for antivirus detect cracks (keygens, etc) like virus...no problem at alll, just ignore or your software won't work (MUST disable antivirus).

ALSO, software won't open if doesn't detect interface, tested yesterday...

[speedy100]

Hello again,

Prior to buy one i am posting here two of the current popular boards that sell these days.
Could You suggest witch is better as a design to become a good working clone after rework as it is suggested in this thread?

396054396055

Thank You :)

[azibi130]

Hello again,

Prior to buy one i am posting here two of the current popular boards that sell these days.
Could You suggest witch is better as a design to become a good working clone after rework as it is suggested in this thread?


396054396055

Thank You :)

i'm still a newbie regarding fg v54 mate.
but i should advert u that the store i buy mine v54, had pictures of "X" pcb, and they sold me one diff from the pics they have on site.


still no one can confirm to me if i can use my power supply of 13.8v and 3 constant amps to feed galletto and, the switch of 12v for bosh ecus??

[azibi130]

i'm soldering the needles to the adapaters, but siemens and marelli are a pain.

eard somehere that marelli doesn't nedd all the needles, true?which ones?
what about the other three adapters, just solder the 10 needles in all other three, or in all 4 (won't marelli ecu damage because other pins that are not need)?

[speedy100]

i'm still a newbie regarding fg v54 mate.
but i should advert u that the store i buy mine v54, had pictures of "X" pcb, and they sold me one diff from the pics they have on site.


still no one can confirm to me if i can use my power supply of 13.8v and 3 constant amps to feed galletto and, the switch of 12v for bosh ecus??

Hello,
Thank You very much for all Your input above.

Your board is the same as in pic. (A) that I have posted. CCDZ type.

About the Power supply, it depends... if Your PS is "up to 3 Amps" it is OK as the unit will draw as much as needed up to 3 A. but if it is the type that "pushes" 3 Amps no matter what then DO NOT USE IT! Usually a few mA. are needed for most functions on flashing...

Best Regards

[azibi130]

my board as yellow relays.

so i bought my power supply for nothing?

[smirnoff_rules]

l use 13.8 with mine and other stuff , you havnt wasted your money , more stable than china one that comes with unit

[azibi130]

this is my power supply
http://www.castroelectronica.pt/product/fonte-alimentao-estabilizada-138v-3--5a


i'm not afraid of the 13.8v (all good with that), my concern is about the 3 constant amps, with 5a surge...so i think it will fry all my tools (mpps,galletto1260,vcds,galletto v54,etc) when i try to read on bench

[speedy100]

my board as yellow relays.

so i bought my power supply for nothing?

Hi again,

The board is the same. The relays are interchangeable parts...
Be careful with the P.S...

Best Regards

[azibi130]

today made some tests with power supply,and i'm going to buy another one.
this PS it's too strong for this ecus jobs loool...

[jakesman]

today made some tests with power supply,and i'm going to buy another one.
this PS it's too strong for this ecus jobs loool...

cant see the problem i have a bench power supply that i can adjust from 2v up to 35v at 15 amps , i normaly set it at 14volt with a car battery as a backup if the power should fail , and i see that most ecu when power up do not realy go above 1 Amp just see a small drop in voltage once it is switched ON so i use 14volt with car battery and never had a problem but yes i see what u say " what if u have a short ?" the AMPS is there to frie every thing

[azibi130]

i buyed this one...
adjustavel volt and amps

http://www.castroelectronica.pt/product/fonte-alimentacao-regulavel-015v-02a-c-display-duplo

[azibi130]

have spent these 2 days trying to get the galletto work ok...no sucess.

i had all ok for about 4 tries in a row (close soft and unplug usb/plug usb and open soft), ok for 4 consecutives times. thought that was finally ok, so i hibernate laptop and go out. when arrived, i plug usb and try to open soft...nothing happens!
try another time but with device manager tree open to see what cames up in drivers...and for my surprise, for the 3 times i unplug/plug interface he shwoed me 3 dif names (tdi, fgtech,serial something...)...
i insisted on unpluging and pluging usb and tried opening soft each time usb was pluged, till one time it opens soft!

what's wrong?why each time i unplug interface everything gets messed??

i'm using win7 x64...on my win xp (2 diff laptops) gets an error opening software, but i think that each time i unplug and plug usb on win xp everuthings stays fine (because i can read and write ftdi eeprom with the usb fixs that came with the cd).
i already write the v54.bin files that came on the usb tools but still the same.

please help...

[azibi130]

finnally i start understanding how the hell this hacks works lol...
i as able to work the software again, but,...restart windows, and again driver was "erased/modified" and had to spent more 30m to instal new driver
and software again just to try k-line on my car edc15p+...

ecu id ok...reading file stopped at 18%, software error...


i'm waiting for fantomel pass for his rar file with 0475 version.
would 0475 be stable?
and how the heck will i solve the driver always modified when "she wants"??

[azibi130]

anyone knows the pass for the fantomel software?

[teerak2uk]

anyone knows the pass for the fantomel software?
Ask him .

[azibi130]

already sent him a PM...maybe is off

[azibi130]

i'm trying to open 0475 but says... "fgtech cannot be verified..." on win 7 x64.

my tool is 0386.

[carmageddon]

change usb cable from tool to computer, bad quality

[azibi130]

change usb cable from tool to computer, bad quality


will try that later night... (does 0475 work with full chineese stock pcb v54 like mine?)

i have instaled the soft from AES, and tomorrow will see if K-line and BDM works.
with china soft k-line stop reading at 18%....

is there any solution to stop software from showing messages for update every minute????

[teerak2uk]

will try that later night... (does 0475 work with full chineese stock pcb v54 like mine?)

i have instaled the soft from AES, and tomorrow will see if K-line and BDM works.
with china soft k-line stop reading at 18%....

is there any solution to stop software from showing messages for update every minute????
Fantomels files show how to change serial as for stability you need to post hq pictures of your galletto pcb so components can be seen clearly

[azibi130]

yellow relays pcb i have...the pic it's the last post on page 70

[teerak2uk]

397033


Compare to this

[azibi130]

i already saw that, thank's...but before i start changing components, i want to try every possibilities with win xp/win7 and software 0386/0475 and see what happens.

that's why i ask:
-does soft 0475 works with stock v54 pcb (tool 0386)?
-what components are a MUST to change?
-AES soft is stable?better in win xp or win 7?

[carmageddon]

the best fg clone are V53_0475 with hw upgraded!
work with xp-7 32-64 bit without problem

-v54 and v53 have same pcb, not the same fw, you need change fw inside LPC2119 and use v53_0475 sw
-you MUST change all components to have stable tool
-aes use the same SW and FW of v54 china, very bad!

[azibi130]

thank's carmageddon...but, i think i didn't get a direct answer...does soft 0475 works with stock v54 pcb (without making any changes)?
because i'm trying to open it but says can't find fgt2xx.dll (i have that file on system32),so i don't understand.

PS: i think i finnally have the soft/hardware working ok till now (AES software).
today i plugged usb galletto and try to open software...and it opened, great.
know will try edc16u34 on bench by k-line and bdm to see what happens.

PS2: why the hell the software is always teeling me this???in 2m i have almost 25 messages!!
on youtubes videos i don't see this message on others guys software, or it's just my impression?

397172

[carmageddon]

the hw aes-china-v53-v54 are the same, you must only change FW on LPC 2119 and use the right SW.

v54 aes and china using same sw and same OLD fw (0386)....the best is v53 (0475)

[smirnoff_rules]

l have a v54 l dont use it alot only bdm really and then only a few times ,use ktag 99% of the time , l have noticed its 0386 in the menu , is it easy to update or is it a pain ?

[teerak2uk]

l have a v54 l dont use it alot only bdm really , l have noticed its 0386 in the menu , is it easy to update or is it a pain ?
It's not so hard

[carmageddon]

i use this with LPC2000 software : http://denkovi.com/usb-to-uart-ftdi-serial-interface-adaptor

https://www.youtube.com/watch?v=vds76AgkQJs (http://denkovi.com/usb-to-uart-ftdi-serial-interface-adaptor)

[smirnoff_rules]

any links to what tools and software l might need ?
l have a J-Link on the way is that any good

[azibi130]

the hw aes-china-v53-v54 are the same, you must only change FW on LPC 2119 and use the right SW.

v54 aes and china using same sw and same OLD fw (0386)....the best is v53 (0475)

you could simply said no :)...


so i need to update the FW to use 0475?that's the reason why 0475 soft won't open?


PS: many thank's to you carma, i changed my ~~~~ty usb cable that came with v54, by the one from my eeprom programmer,
and i could read/write edc15p+ by K-Line with no problem :). AND NO MORE MESSAGES EVERY 5 SEC

will test edc16 tomorrow, but i have a huge doubt, despite many info on the web...

heres my adapters with needles soldered....are they ok?

397195

bosch
397196

delphi
397197

marelli
397198

siemens
397199

but heres my doubt, why the hell the bosh adapter has only 10 needles and on the pdf says it uses 12?
on ecu we have 14 pads, but wich one to connect RIGHT without burning ecu?see more than 3 ways that ppl read??

[azibi130]

for those users with fgtech galletto 4 v54 that can't comunicate k line, try to change the usb cable and turn the laptop bat settings to full performance...
worked for me and for many others on th world...

[smirnoff_rules]

you could simply said no :)...


so i need to update the FW to use 0475?that's the reason why 0475 soft won't open?


PS: many thank's to you carma, i changed my ~~~~ty usb cable that came with v54, by the one from my eeprom programmer,
and i could read/write edc15p+ by K-Line with no problem :). AND NO MORE MESSAGES EVERY 5 SEC

will test edc16 tomorrow, but i have a huge doubt, despite many info on the web...

heres my adapters with needles soldered....are they ok?

397195

bosch
397196

delphi
397197

marelli
397198

siemens
397199

but heres my doubt, why the hell the bosh adapter has only 10 needles and on the pdf says it uses 12?
on ecu we have 14 pads, but wich one to connect RIGHT without burning ecu?see more than 3 ways that ppl read??
397203 here m8

[azibi130]

smirnoff, i already know that, that's what i asked.

on the pic we can see that the pins are located diff that on my bosch adapter.

on pic we have:
. . . . | .
. . . . | .

on my adapter i have:
. . . . .
. . . . .

why?it says bosch adapter if the needles points doesn't match?

please help, don't want to burn ecu, it's my 1st attempt for bdm

[smirnoff_rules]

my set are like this
. . . . | .
. . . . | .

but yours will have no power or connection on them spare ones , you could even remove them , seen cheap ones like this on the net

[azibi130]

you know we are in chineese clone topic right :)...off course my adapters are s h i t t also heheh...

this adapters are from bdm frame.
i have other 4 adapters that came with galletto, but the set up are like this:
. . . . . .
. . . . . .

still no separation between last 2 points, but eard that galletto doesn't use that 2 points ( | ).

i will do a continuity test to see if pinout it's the same on both adapters.

[azibi130]

http://www.lesamisdelaprog.com/lecture-ecriture-ecus/7987-tuto-petite-aide-lecture-edc16-fgtech-galletto-v5x-bdm-table.html

[azibi130]

post of jean22 with a pic and some french i understand

[carmageddon]

any links to what tools and software l might need ?
l have a J-Link on the way is that any good

sw for usb--uart is philips LPC2000 with ftdi drivers downloadable from web

for the tool you can click on the link...or find other tool usb---uart

[pablo1971]

i have V54 CHINA CLONE...it has a dongle and its just stopped working....can anyone help me with dongle free software plz.

[smirnoff_rules]

http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386 this will help

[YoungDan]

You pm box is full

bubu55 im looking to buy an updated fgtech please inbox me

[teerak2uk]

bubu55 im looking to buy an updated fgtech please inbox me
Pm me .

[vanos batam]

you know we are in chineese clone topic right :)...off course my adapters are s h i t t also heheh...

this adapters are from bdm frame.
i have other 4 adapters that came with galletto, but the set up are like this:
. . . . . .
. . . . . .

still no separation between last 2 points, but eard that galletto doesn't use that 2 points ( | ).

i will do a continuity test to see if pinout it's the same on both adapters.


no problem you can use like your pict post..
delphi and Bosch adapter no problem

[YoungDan]

inboxed mate

[azibi130]

no problem you can use like your pict post..
delphi and Bosch adapter no problem

only just like this?

397342

and the rest of the wires connected?

won't be miss match of needles from galletto to the ecu??

[vanos batam]

only just like this?

397342

and the rest of the wires connected?

won't be miss match of needles from galletto to the ecu??


Yessssssssssssssss!!!!!!!!

[azibi130]

Yessssssssssssssss!!!!!!!!

thank's

will try that next week, will have to get new power supply already ordered...


does anyone can point me where to get info about the meaning of:

- VF0, DSCK, PORST, DSDI, DSD0??

[azibi130]

anyone?
i'm tired of looking on web but nothing...frustrating!

i want to understand the meanings of bdm connections names....

[azibi130]

no one's interested in that....

[ddnc]

Why do you want to know that?? Just use it as the above photo and you are good to go. Done C39 and U31 without problems.

[smirnoff_rules]

Background debug mode (BDM)

[azibi130]

Why do you want to know that?? Just use it as the above photo and you are good to go. Done C39 and U31 without problems.

how much Amps should i use on power supply + igniton switch?

tomorrow i'll get my PS, 0-15v and 0-2A, that PS is for galletto and ignition switch, that's why i ask.

if i set the current for 1a, is it good enough for galletto and igniton switch also?

[smirnoff_rules]

13.8V 3A works for me but 1/2 amp will be ok

[azibi130]

heres my first attempt bdm, good ;)

https://www.youtube.com/watch?v=4r-nF5DEh00&feature=youtu.be

[smirnoff_rules]

nice and easy them , have you setup your laptop in battery/charge settings not to go to sleep ?

[azibi130]

nice and easy them , have you setup your laptop in battery/charge settings not to go to sleep ?

yes, HDD, and screen never slip

i have 3 os installed on laptop. 2 win7 and one XP.
1 win7 no antivirus and full performance laptop (i only plug charger because low bat :) , before video i was playing with it only with bat mode and bat went down)
xp for hacked stuff
and the other win7 for work loool

the hard it's the first time, then you know. more confident...

conclusion, just do what chineese tell you on manuals lol

[ddnc]

Better stabilize it at minimum 13V or you might have surprise wile writing.

[azibi130]

Better stabilize it at minimum 13V or you might have surprise wile writing.

even with a stabilized power supply u think it's better 13v? i thought in 13v also, but tried the
"same voltage" as ps from galletto xina, it must work i thought, so give a try.

but remenber that i'm feeding galletto and ecu switch by the same PS...
13v it's safe for ecu and galletto?

but thank's for the tip ;)

[smirnoff_rules]

you didnt read my post on the other page then 13.8 is best , no danger , if powering two units then your best over 12v

[PremierD]

Power up using car battery ... never fails .:)

[azibi130]

you didnt read my post on the other page then 13.8 is best , no danger , if powering two units then your best over 12v

tomorrow will try with 13v and 13.8v.

thank's

[azibi130]

today i was able to see what components i have on my pcb, and this is what i have:

U14 - U9 - U19 = LS14 nxp
U8 - U17 = 74 HCT 125D nxp
U11 - U15 = 74 HC 245D nxp
U20 - U22 = MAX 485 ESA +
U16 - U23 = L-9613 ST
U10 = 82C250Y
U21 - U12 = LM 393
U18 = HEF 4011 BT (this one is no nxp, at least doesn' say on chip)
Q18 = ZVP 2106A
Q20 = ZVP 2106A
Big relays are aromat
Small relay is Sunhold
Y1 = yellow ressonator
C21 - C26 - C28 = 100uF 50v (the three capacitors near C27 are also 100uF 50v)
and the other 4 small capacitors are 10uF 50v

i can see symbols from phillips, nxp and ST on the chips
K-Line R/W worked on edc15p+ on car, and edc16u34 on the bench.
BDM read/write worked on edc16u34

i ask please which components would be a must to change?

[carmageddon]

U14-U9-U19 are 74HC14D

U8-U17 are 74HCT125D

U11-U15 are 74HC245D

U20-U22 are MAX485ESA+

U16-U23 are E-L9637D

U10 are PCA82C250

U21-U12 are LM393

U18 are HEF4011BT

Q18 are ZVP2106A

Q20 are ZVN2106A

big relais : G6AK-234P ST-US 5VDC

small relais : G5V-1 5VDC

Y1 change resonator with quartz 16 mhz

c21-c26-c28 100uF 50V

the other 7 capacitor are 10uF 50V

[azibi130]

U14-U9-U19 are 74HC14D

U8-U17 are 74HCT125D

U11-U15 are 74HC245D

U20-U22 are MAX485ESA+

U16-U23 are E-L9637D

U10 are PCA82C250

U21-U12 are LM393

U18 are HEF4011BT

Q18 are ZVP2106A

Q20 are ZVN2106A

big relais : G6AK-234P ST-US 5VDC

small relais : G5V-1 5VDC

Y1 change resonator with quartz 16 mhz

c21-c26-c28 100uF 50V

the other 7 capacitor are 10uF 50V

i already saw your list carma, thank's.

but to be more specific, i want to know which components of this list are related to:
- k-line
- Can line
- bdm

so i can make proper changes to where i want...

because i have almost 50% of the right components of the list.
397873

[bobolin4o]

i already saw your list carma, thank's.

but to be more specific, i want to know which components of this list are related to:
- k-line
- Can line
- bdm

so i can make proper changes to where i want...

because i have almost 50% of the right components of the list.
397873

So, change the other 50% and stop flooding here!
Regards!

[azibi130]

R/W in bdm for 5 times consecutive...ALL ok edc16u34 - 2.50 minutes at 3.3v on software with 13v on PS (galletto show 13.5v)
Read K-Line edc16u34 - 3m (immo is on so can't write)
Read Can edc16u34 - 14m (immo is on so can't write)

for everyone interested to know...

[JasonP]

the link is off

[azibi130]

i eard somehere that couldn't be possible to have galletto v54 and other any tool that uses ftdi driver.
so that galletto doesn't give trouble.

not true!


today i used mpps v13 to read marelli and, and then i used galletto v54 to see if it's was true, but everything worked ok.
Same win7 x64 for both tools

PS: JasonP manda mensagem privada

[Roberto68]

Hello,
i made a Part List with Rework Components incl. farnell.com Part Nr.
Can someone please check it?

farnell.com Part Nr.

U14 - U9 - U19 = 74HC14D ---------------------- 1201316
U8 - U17 = 74HCT125D -------------------------- 1201306
U11 - U15 = 74HC245D -------------------------- 1201324
U20 - U22 = MAX485ESA+ ------------------------ 2519382
U16 - U23 = E-L9637D -------------------------- not found @ farnell
U10 = PCA82C250 ------------------------------- 2400543
U21 - U12 = LM393A ---------------------------- 4586128
U18 = HEF4011BT ------------------------------- 1085279
Q18 = ZVP2106A -------------------------------- 9525505
Q20 = ZVN2106A -------------------------------- 9525432
Big relays = G6AK-234P ST-US 5VDC ------------- 1181048
Small relay = G5V-1 5VDC ---------------------- 9949577
Y1 = Quartz 16 mhz ---------------------------- 9713700
C21 - C26 - C28 = 100uF 50v ------------------- 1822685
and the other 4 small capacitors = 10uF 50v --- 2368692
3 capacitors near (right) LPC2119 ------------- 8126976
3F = BC857C ----------------------------------- 8734771
6BW = BC817-25 -------------------------------- 1081224
WV4 = BAT54S ---------------------------------- 1081194
ADAA = MAX809S -------------------------------- 2512754
U5 - U6 = LP2951ACM --------------------------- 9493425
Q1 = BC337-25 --------------------------------- 1574380

Thanks

[azibi130]

seems right

[Roberto68]

Hi,
are the parts that I have chosen to Farnell.com OK?

[azibi130]

galletto v54 only reads 64kb of 6jf 1.3 marelli, while mpps v13 reads full read 448kb

[ddnc]

Nop, it reads 2048kb

[carmageddon]

Nop, it reads 2048kb

6jf dont have 2 mb flash, only 6f3 have it

[azibi130]

6jf dont have 2 mb flash, only 6f3 have it

correct carma.

[ddnc]

6JF read inside the MPC5xx micro instead of external flash from 6F3.
My bad

[Roberto68]

Can someone Help me Please!

[bobolin4o]

Can someone Help me Please!

Look (http://www.digital-kaos.co.uk/forums/showthread.php/411050-Chineese-Galletto-V54?p=2849768&viewfull=1#post2849768) at #1127 (http://www.digital-kaos.co.uk/forums/showthread.php/411050-Chineese-Galletto-V54?p=2849768&viewfull=1#post2849768)

[vanos batam]

nothing news about higer firmware galletto?
maybe V55 v56 ???

[Babos]

Fgtech from 2014 start work via internet online.

[vanos batam]

Fgtech from 2014 start work via internet online.

clone no read this ecu..http://www.digital-kaos.co.uk/forums/showthread.php/529565-PCM-Motorola-NCG5-Chrysler-Dodge-%E2%80%93-Jeep
and http://www.digital-kaos.co.uk/forums/showthread.php/514915-NGC-5-jeep-PCM
may i have solution please !!

[midnightman1]

Have anybody firmware and software for v53?

I have revorked v54..want to downgrade to v53..... any tutorial?

thanks!!!

Viktor

[FUSED:]

Fgtech from 2014 start work via internet online.


hi all,anyone to make this file virgin for me,GREATWALL>WINGLE

regards

[azibi130]

Have anybody firmware and software for v53?

I have revorked v54..want to downgrade to v53..... any tutorial?

thanks!!!

Viktor


http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386

[rgnaya]

i have broken transistor bc335-25 on my galletto. local dealer only have "TRANSISTOR BC337 NPN 50V 0.8A 0.625W 100 MHz TO-92" and i need to work with my machine now and do not want to wait for another unit for farnell... could i put this transistor? so thanks.

[tango]

did you even look at the original picture ?
and also did you not look at the parts list?
because if you did then you would see the unit uses a bc337 not a bc335

[rgnaya]

sorry! i wanted to write bc337-25! and yes, i have read the list and see the picture so many times, and will see it more times again... but, is this possible to put this transistor?

[tango]

the picture of the original and the parts list clearly says bc337 therefore your board having a bc335 in it was wrong and needed changing to a bc337 anyway
so simple logic the answer is yes use bc337

[FUSED:]

hi all,anyone to make this file virgin for me,GREATWALL>WINGLE

regards

hello guys anyone to help me make this ECU file virgin BOSCH 0 281 013 328 EDC16C39 for greatwall

kind regards

[tango]

without the file noone can do anything

[FUSED:]

without the file noone can do anything

this is the file my friend
sorry my mistake

regards

[azibi130]

mate this is "Chineese Galletto V54" thread

[tango]

yes sorry i should have also said make your own thread in the correct section with your request

[TurboTuur]

useless version of tool!

dont buy it

What exactly is wrong with this version mate?

I already bought it and indeed, it's not working, the relais are constantly clicking when connected to the usb. I've checked all the hardware using your list and this is what i came up with so far:

U14-U9-U19 are 74HC14D nxp all ls14
U8-U17 are 74HCT125D nxp correct
U11-U15 are 74HC245D nxp correct
U20-U22 are MAX485ESA+ correct
U16-U23 are E-L9637D L9613
U10 are PCA82C250 nxp no text
U21-U12 are LM393 correct
U18 are HEF4011BT nxp correct
Q18 are ZVP2106A correct
Q20 are ZVN2106A ZVP210 6A
big relais : G6AK-234P ST-US 5VDC DS2YE-SL2-DC5V
small relais : G5V-1 5VDC THA-5-L
Y1 change resonator with quartz 16 mhz ZTT 16OM.X
c21-c26-c28 100uF 50V correct
the other 7 capacitor are 10uF 50V 3x 100uF 50v

The wrong ZVP bothers me the most and also the wrong capacitors, could this be causing the on and off switching of the unit?

Also would it be worthwhile replacing all the parts or do you have a better alternative to just buy a new one?

[TurboTuur]

Looking at pictures online it does seem to be a cheap version vs looking at the rest. Decided to buy a better one and fix the board on that one :)

[javyb]

What is the latest year bag Siemens pcr 2.1 ecu people have managed to unlock with v54? I struggled on a 2012 ecu, I'm the end unlocked direct by reading eeprom

Sent from my SM-G935F using Tapatalk

[kospoz]

Skoda rapid 1.6 2013 the latest that i have done

[kptuning]

Read skoda 1.2 tsi simos 10 with v53 hardware updated sw v54
Its in the list but chines clones cannot do it

Mine read golf 1.2 tsi just good, but is it good for writing?

[jakesman]

ok today my galleto stoped working , open it and found the 1117cd 1.8 gets real hot and also galleto not reconised by usb , desolder the legs from it and galleto is reconized again by usb , the 1117cd 1.8 and 1117cd 3.3 is both voltage regulators for 1.8 volt and 3.3 volt , i did not test it futer , the 2 indicator lights by the usb side only 1 work , ok when i give it 12 volt these regulators do not get hot only with usb , so for what is this regulators ? BDM because i had a faulty ecu and after BDM attempt the galleto did this , BDM went fine first time identify but stoped middle of the read and then all dead , with what other transistors can i swap it out for , the lm317 have same pin out but specs is way off

[smirnoff_rules]

l believe its this one for bdm l ordered one the other day for a spare fgtech that didnt like bdm reading

havnt got around to swapping and trying .. not a fan of bdm with these anyway , go straight to my ktag

https://i.gyazo.com/2de19e735696f8f5696fa83e20d0e2a0.png

[kospoz]

Can someone tell which part is for renesas mode?i tried with opel denso and at the end i have error wire 2 and 3

[jakesman]

awww this thing is a piece of crap , buy new one k-line not work rework then bdm start then can then then ........ i think the older version is more stable like galleto v2 I dnt see 78 pages about that one so i buy v50 or 53 and think it will have less problems and rework storys , time spend on rework and looking for why what is not working it would have been better to get a good EU clone or older version and add a good quality kess and ktag and oops here we go again kess ktag tokens rework the sh*t never ends ........Buy original but we dnt all have the $$$$$ to do so

[Multipla]

today i was able to see what components i have on my pcb, and this is what i have:

U14 - U9 - U19 = LS14 nxp
U8 - U17 = 74 HCT 125D nxp
U11 - U15 = 74 HC 245D nxp
U20 - U22 = MAX 485 ESA +
U16 - U23 = L-9613 ST
U10 = 82C250Y
U21 - U12 = LM 393
U18 = HEF 4011 BT (this one is no nxp, at least doesn' say on chip)
Q18 = ZVP 2106A
Q20 = ZVP 2106A
Big relays are aromat
Small relay is Sunhold
Y1 = yellow ressonator
C21 - C26 - C28 = 100uF 50v (the three capacitors near C27 are also 100uF 50v)
and the other 4 small capacitors are 10uF 50v

i can see symbols from phillips, nxp and ST on the chips
K-Line R/W worked on edc15p+ on car, and edc16u34 on the bench.
BDM read/write worked on edc16u34

i ask please which components would be a must to change?

Which be the interested party, the can line? Tanks

[miralem]

After reading this thread, I bought for me china clone, hope it will be as they told me it would be, and here is some tips that I copied from hard/working friends that were willing to help us:

_________________________________________________
obd R-W with temp under 50? only on renault-bosch diesel

renault-siemens diesel dont have this strategy
__________________________________________________ __________
tprot on vag are present from 05/2009 but is very random this option, is most present on engine with low power and is not compeer to years or ecu type.
the best way to know if tp is active is always bootmode and read tag on file
__________________________________________________ ________________________________

desold resonator, clean central hole, place a piece of ribbon or paper on central hole, resold up the quartz.
__________________________________________________ _________________________________
don't use this tools for checksum correction, there are better ways like using winols or something in that way.
__________________________________________________ _________________________________

Important is also U2. You have a rezistor and a cap instead of tranzistor and it has impact direct in bdm and bootmode.

__________________________________________________ _________________________________

U2 "S5B" is the same as "ADAA". Made by texas instruments.
__________________________________________________ _______________

You should have only one missing resistor, 4.7kohm near U19. The rest are empty places.
__________________________________________________ ________________________

BDM timing is dependent of software and system clock (crystal or ceramic resonator), other components can't have no effect in speed.
__________________________________________________ ________________________________

ZVN and ZVP transistors are connected to OBD pins 2 and 10,

this two are used for J1850 protocol, so cars that use it, will not work (some ford e.g.)
__________________________________________________ _____________________________

K-line repair consist of chips U16 and U23 both are E-L9637D

__________________________________________________ ________________________________


70% of problem on this tool is not HW but SW....bad cracked and without stability (and old for v54_0386)....on HW you can play how you need.
__________________________________________________ ________________________________


V54(0386) is poor cloned version. Firmware need downgrade to V53(0475), then can use newest(11/2012) soft which is also better cracked than V54 soft.
__________________________________________________ ________________________________


SN 0386 and SN 0475 both is fw53 not 54 !

difference only one... 0386 use sw from 11/2012, 0475 use sw from 12/2012 (can read/write epp in pcr2.1 ecu)
__________________________________________________ ________________________________


fg 49-50-51-52 are ALWAYS v48!
__________________________________________________ ________________


galletto eu have ONLY pcb better, nothing else!

v53_0475 china hw-sw upgraded is better
__________________________________________________ _


desold resonator Y1, clean central hole, place a piece of ribbon or paper on central hole, resold up the quartz.
__________________________________________________ _________________________________

replaced Q20 with 2N7000
____________________________________


usb cable from tool to computer, bad quality
__________________________________________________ _


-v54 and v53 have same pcb, not the same fw, you need change fw inside LPC2119 and use v53_0475 sw
-you MUST change all components to have stable tool
-aes use the same SW and FW of v54 china, very bad!
__________________________________________________ ___-

use this with LPC2000 software : http://denkovi.com/usb-to-uart-ftdi-serial-interface-adaptor
https://www.youtube.com/watch?v=vds76AgkQJs
__________________________________________________ ___

Pay attention to this parts on your PCB and compare with the one in this table, and if they are not like those, or like allowed one, change them with the one in table below






U14-U9-U19

74HC14D nxp



U8-U17

74HCT125D nxp



U11-U15

74HC245D nxp



U20-U22

MAX485ESA+



U16-U23

E-L9637D



U10

PCA82C250 nxp



U21-U12

LM393



U18

HEF4011BT nxp



Q18

ZVP2106A



Q20

ZVN2106A



2 big relais

G6AK-234P ST-US 5VDC



1 small relay

G5V-1 5VDC



Y1

quartz 16 mhz



c21-c26-c28

100uF 50V



the other 7 capacitor

10uF 50V




_____________________________________________

[dadal]

I have read 78 Pages and made notes exactly like you ( and I see now your notice ,,pain pain pain )
Next time I will read out from the last page to first page :)

[miralem]

I received mine a few days ago, and after some promises that it will be all Omrons and so one and so one , I have just received this:
413954

And this is from the back...
413955

It even dies not have Q20 and 18, and I dont have it with me...

[mrchip]

Hi Mates,

I wanted to rework my galetto ( replace U16-U23 by E-L9637D)
as you can see in the photos some soldering pads of U16 broken. I want to connect these legs of L9637D directly via wires to circuit board,( not via traces because pads are broken).

I cant find/see connection points( trace) of some legs on circuit board.
Can someone check it please ( continuity test by multimeter) ? I cant find connection point of 3 pads/pins
418758

https://s29.postimg.org/o74393tjr/Knipsel.png

[mrchip]

Hi Mates,

I wanted to rework my galetto ( replace U16-U23 by E-L9637D)
as you can see in the photos some soldering pads of U16 broken. I want to connect these legs of L9637D directly via wires to circuit board,( not via traces because pads are broken).

I cant find/see connection points( trace) of some legs on circuit board.
Can someone check it please ( continuity test by multimeter) ? I cant find connection point of 3 pads/pins
418758

https://s29.postimg.org/o74393tjr/Knipsel.png


please can someone help

[street2maxx]

I need the software version of 2016 or 2017 , which one support denso ecu from toyota avensis.

[dorofteius]

Try original.
I need 10K E. But nobody gives.
Be realistic mate.
Good piece off clone exists. As I have-it, but when it has produces allot off money, then you buy the real one.
I am at almost there.

[pulsar2000]

BDM Problem China v54,
probably been covered, and im sure i read somewhere already but cant find, my china v54 on BDM screen hangs when go to read,
whats the components needed for a fix,
might get round to changing at some point if i know where im looking at and what to change,
works ok OBD, but BDM the screen sort of Freezes and hangs,
cheers

[smirnoff_rules]

you need to see if you have 2 of these fitted in the middle m8 http://www.ebay.co.uk/itm/131716779041?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

unlike this picture

https://i.gyazo.com/d4c90db165254cedf511151777bdd5bf.png

[pulsar2000]

Excellent will take a look its no real issue as have a Proper v54 , its a spare test piece i suppose the china one, just ordered one as wanted to see how good they were,
More shopping LOL m8, Bearings on order :chuncky:

[pulsar2000]

you need to see if you have 2 of these fitted in the middle m8 http://www.ebay.co.uk/itm/131716779041?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

unlike this picture

https://i.gyazo.com/d4c90db165254cedf511151777bdd5bf.png
would appear i have same as in your Photo, so i need to replace these 2 yes

[gazvts]

3 of them on the board chap 1 beside q18/q20

[pulsar2000]

Ok thanks will order up some and try

[mrchip]

Hi Mates,

I wanted to rework my galetto ( replace U16-U23 by E-L9637D)
as you can see in the photos some soldering pads of U16 broken. I want to connect these legs of L9637D directly via wires to circuit board,( not via traces because pads are broken).

I cant find/see connection points( trace) of some legs on circuit board.
Can someone check it please ( continuity test by multimeter) ? I cant find connection point of 3 pads/pins
418758

https://s29.postimg.org/o74393tjr/Knipsel.png

can someone help me please ??

[mrchip]

yeesssssss I did it :stung: it works again,,, my galletto has now 2nd live ( I find it unfortunate that no one has helped )
anyway it works now good
:celticparty:

[diplo]

Hello, somebody can tell me, is it the same, OMRON G6AK-234P -ST-US 5VDC and OMRON G6AK-234P 5VDC ? Is it important without ST-US ?
Thank you.

[jsg1200]

Hi guys.

I have a v54 chinesse, and i update HW with photo of fantomel.

But, I not change ls74, and I dont know if its necesary resistor 222 and resistor 472.

My line Can not work.

Regards ;)

[jsg1200]

My line "CAN" not work.

[Feilng]

clone v54 hard to install on win7.

[azibi130]

clone v54 hard to install on win7.

loool....

i spent 4 days till i finnally understand what was the problem...know it works ok every time i use it

[kospoz]

My line "CAN" not work.

Bootmode is working?

[jsg1200]

Hi.

Yes. Bootmode, line K.

I cant write edc16c3 of Ford 1.6tdci but I can read this ecu.

Mpps v13 and galletto v54 can read, but dont can write...

Regards ;)

[kospoz]

Hi.

Yes. Bootmode, line K.

I cant write edc16c3 of Ford 1.6tdci but I can read this ecu.
Mpps v13 and galletto v54 can read, but dont can write...

Regards ;)
Mine has also can bus problem by obd but in bootmode can bus is working.If you want to try something pm me

[ankjay]

Hey guys,

So I've just received one chinchon (means china) clone from FG Galletto with the V54 (apparently...).

I've installed the drivers correctly and the software as well (again, apparently...).
There are few things that I consider strange. Let me enumerate them:
I've installed on Windows XP Pro x86, clean software installation, installed the FG Tech software from the CD that they gave me and... bum! A big cabum with the Microsoft C++ Runtime error. I've installed the Microsoft C++ Redistributed 2005, 2008 and finally 2010 package but same thing...

So I though: "Maybe it's a software problem... ok let's install the Win 7 x86."
Installed again the software and drivers and that thing and the application won't run. It simply shuts down and the reason that windows give is "FG Technology stopped working". And that's it.

I've searching that this might need an eeprom reprogramming but... I received it yesterday. Is it really necessary? :(
Any tips?

Thanks in advance guys!

[Suv4x4]

I have bought a chinese clone V54 latest claimed 2017 version. I have done all the tricks possible to make this tool work. I have written n number of ept files till now, followed all the different processes like setting the system date to 1/1/2013 , installing correct drivers and what not. But this tool does not budge. When i connect to any of the cars the software opens properly, it shows tool no 0386, it shows correct voltage. But when i select the driver and try to connect to any of the cars it throws an error as shows in the picture
Attention!! Send File C:\FGTECH\EOBD2_LOG\_ebod2_XXXXXX_ERR.gal to support@fgtechnology.it

I have been breaking my head over this tool since 5 days now without any success. I have not done any hardware changes yet. I have ordered a USB to TTL converter to write MCP with 0475 version now. But i doubt if that will work for me.

Request all the senior members and expert to please help me on this.

425259425260

[ankjay]

I have bought a chinese clone V54 latest claimed 2017 version. I have done all the tricks possible to make this tool work. I have written n number of ept files till now, followed all the different processes like setting the system date to 1/1/2013 , installing correct drivers and what not. But this tool does not budge. When i connect to any of the cars the software opens properly, it shows tool no 0386, it shows correct voltage. But when i select the driver and try to connect to any of the cars it throws an error as shows in the picture
Attention!! Send File C:\FGTECH\EOBD2_LOG\_ebod2_XXXXXX_ERR.gal to support@fgtechnology.it

I have been breaking my head over this tool since 5 days now without any success. I have not done any hardware changes yet. I have ordered a USB to TTL converter to write MCP with 0475 version now. But i doubt if that will work for me.

Request all the senior members and expert to please help me on this.

425259425260

From what I know, I believe that yellow Aromat relays aren't the right ones.
You need to rework your PCB in order to make it work properly.

Regarding the error, I believe that's an hardware/firmware problem. Mostly firmware.

Mine doesn't even start the application. :-(

[bobolin4o]

From what I know, I believe that yellow Aromat relays aren't the right ones.
You need to rework your PCB in order to make it work properly.

Regarding the error, I believe that's an hardware/firmware problem. Mostly firmware.

Mine doesn't even start the application. :-(


Nonsense... Mine FG is with the same relays.
Work more then OK
I've changed only the LS14 chips...

[ankjay]

Nonsense... Mine FG is with the same relays.
Work more then OK
I've changed only the LS14 chips...

Hum, I've read it here that they aren't good. Thanks for your reply!
Just a newbie in the woods mate. :-)

By the way, I believe I've sorted out what the problem is. My chinchon galletto probably needs to fix the HEX DUMP. :-(
God damn it!

[vasco fernandes]

i have fgtech equal, work fine

[gazvts]

if you haven't changed hex can use AES version

[ankjay]

if you haven't changed hex can use AES version

Thanks mate. I've managed to get one USB-TTL adapter from a colleague at my work anyway.
I'll try to use the AES Version in order to fix it. :-)

Just to confirm: the AES Version is the Program 0386 from this topic: http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386?highlight=galletto+v54 , right?

[Suv4x4]

my friend exchanged the photos of his chinese board which works perfectly. i just noticed that the boards are very similar only with the different relays- again not omrons. then i could notice his tool version is 0475. does it mean the hex on my tool is wrong. i guess in this case i would need to use the fantomels guide to change the tool version from 0386 to 0475 using the usb to ttl adaptor. Am i missing something?

[ankjay]

my friend exchanged the photos of his chinese board which works perfectly. i just noticed that the boards are very similar only with the different relays- again not omrons. then i could notice his tool version is 0475. does it mean the hex on my tool is wrong. i guess in this case i would need to use the fantomels guide to change the tool version from 0386 to 0475 using the usb to ttl adaptor. Am i missing something?

I've managed to get mine working, but it's 0386. :)
I've used the fantomel programs and guides (cheers mate!!) and now it starts the program.

I don't have an available car in order to check if it reads or identifies the ECU.
But when I choose a driver in EODB and do the "Ecu Data" the galletto starts to click. I believe that's normal.

After that he can't connect (of course) and it give error (expected...).

Now I have a question: what's the power supply that you guys use? I'm talking only read/write via OBD.
For BDM I was thinking getting another one, of course.

[pulsar2000]

Obviously OBD not required,
Boot mode and BDM use a 0-36v 5.0ah bench precision Supply as recommended and endorsed by Smirnoffrules !
about ?40
absolute perfect psu.
Be interested to hear if your BDM function works,
cheers

[Suv4x4]

I shall try to use fantomels aes program with my 0386 tool. As said earlier getting the eobd2 to work is not an issue for me, every time my program opens, also when connected to the car it shows correct voltage. But when I select drivers and click on read ecu id or read ecu I get the error.

[Suv4x4]

ok i did a totally fresh install, removed all old versions, deleted all drivers etc and set my laptop (win7) date to 1/1/2013. Then used mprog to flash fantomels ept and wrote the eprom too. Then installed the AES software from fantomels files. The software starts perfectly like it always does for me, shows ECU voltage and then which i click ecu read i get an error.
This is driving me nuts. tomorrow my USB to ttl converter shall arrive. I will try changing the MCY hex to 0475 tool. thats my only hope before i start making hardware changes.

[ankjay]

Obviously OBD not required,
Boot mode and BDM use a 0-36v 5.0ah bench precision Supply as recommended and endorsed by Smirnoffrules !
about ?40
absolute perfect psu.
Be interested to hear if your BDM function works,
cheers

I still haven't received the BDM structure... So I can't tell you if it works.
But when it arrives, I'll let you know. :-)

I'll order a psu as well!


ok i did a totally fresh install, removed all old versions, deleted all drivers etc and set my laptop (win7) date to 1/1/2013. Then used mprog to flash fantomels ept and wrote the eprom too. Then installed the AES software from fantomels files. The software starts perfectly like it always does for me, shows ECU voltage and then which i click ecu read i get an error.
This is driving me nuts. tomorrow my USB to ttl converter shall arrive. I will try changing the MCY hex to 0475 tool. thats my only hope before i start making hardware changes.

I haven't tried to read an ecu but this weekend I will try one, for sure and I'll let you know. ;-)

[gazvts]

I shall try to use fantomels aes program with my 0386 tool. As said earlier getting the eobd2 to work is not an issue for me, every time my program opens, also when connected to the car it shows correct voltage. But when I select drivers and click on read ecu id or read ecu I get the error.what vehicle ?

[Suv4x4]

Fiat punto, tata safari, none of these work

[Suv4x4]

Today I changed all the capacitors and 3 LS14 hex inverters. Still no success. I couldn't get the omron relays so retained the original ones

[dadal]

Today I changed all the capacitors and 3 LS14 hex inverters. Still no success. I couldn't get the omron relays so retained the original ones

dont change some parts, change all parts + software 0475 ( read post of Fantomel)
I had also problems with galletto, it works now perfect without problem for ex. read/write full flash Sagem S3000, sirius32,
you'll feel the difference

[Suv4x4]

Nonsense... Mine FG is with the same relays.
Work more then OK
I've changed only the LS14 chips...

Hello Sir, thanks for the inputs. I retained those relays as i couldnt find the omron ones. I changed all the LS14 to 74HC14 and the capacitors.
Apart from LS14 did you change any SMDs?

I am still not able to read any damn ECU. i have started getting a doubt that the tool itself is jinxed and wont work even if i change components further.
I just need to read via OBD and no other function.

[roth18]

Look for solution by member Fantomel

Sent from my SAMSUNG-SM-G900A using Tapatalk

[ZetorGumi]

Hi!

I Was recently buy a chinese Galetto V54 (Tool number: 0386 :( )
I was trying to start the program in XP 32 bit (Fresh install, just drivers), and Win7 32bit (Fresh install too).
The problem is same in the 2 OS's.
I was installed the program, connect the tool, install driver in the FGTech folder, and install again the program, and the Win7 patch (In xp, i didn't install the W7 patch)
And i started it.
The program was making an error:
APPCRASH
Timestamp: 5090ef18
StackHash_0a9e

What is this?
What's the solution?

Thanks. David.

Ps.: Sorry for my bad english. :)

[smirnoff_rules]

in device manager can you see fgtech is installed

[ankjay]

Hi!

I Was recently buy a chinese Galetto V54 (Tool number: 0386 :( )
I was trying to start the program in XP 32 bit (Fresh install, just drivers), and Win7 32bit (Fresh install too).
The problem is same in the 2 OS's.
I was installed the program, connect the tool, install driver in the FGTech folder, and install again the program, and the Win7 patch (In xp, i didn't install the W7 patch)
And i started it.
The program was making an error:
APPCRASH
Timestamp: 5090ef18
StackHash_0a9e

What is this?
What's the solution?

Thanks. David.

Ps.: Sorry for my bad english. :)

Hi mate,

Probably you've the same problem has I did.
Install the 0386 software with the AES version.

Also, install the drivers that are in this topic: http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386?highlight=galletto+v54

[Suv4x4]

Thanks to Fantomel I made all the mcu changes by using a usb to ttl converter and flashing the 0475 version using the LCP2000. All went well and now my tool shows 0475 version in the eobd2 program for 0475 version.
But again the same issue. Connected to a fiat punto and clicked on ecu id and it throws the same error.
I am somehow sure now it's a hardware issue.
I have already changed the 3 LS14s and all capacitors. Relays are ordered. What else controls the read from obd

[ZetorGumi]

Hi mate,

Probably you've the same problem has I did.
Install the 0386 software with the AES version.

Also, install the drivers that are in this topic: http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386?highlight=galletto+v54


Hi.

I was downloaded the program that you linked.
And it didn't help. :O
Fresh Win7 x32, and it misses the "FGT2XX.dll"..

[ankjay]

Hi.

I was downloaded the program that you linked.
And it didn't help. :O
Fresh Win7 x32, and it misses the "FGT2XX.dll"..

Did you installed the AES flasher in the same folder as the FGTech?
I did that and it started to work.


Thanks to Fantomel I made all the mcu changes by using a usb to ttl converter and flashing the 0475 version using the LCP2000. All went well and now my tool shows 0475 version in the eobd2 program for 0475 version.
But again the same issue. Connected to a fiat punto and clicked on ecu id and it throws the same error.
I am somehow sure now it's a hardware issue.
I have already changed the 3 LS14s and all capacitors. Relays are ordered. What else controls the read from obd

I've tested today the reading of an EDC16U34 and all went well, on Can Line. :)
I've made some newbie mistake, I've selected the wrong driver and it send the wake error. But after I choose the CAN-Line and the proper driver it reads the ECU.

[ZetorGumi]

Did you installed the AES flasher in the same folder as the FGTech?
I did that and it started to work.


Yes, i was installed the flasher, and it didn't help.

[ankjay]

Yes, i was installed the flasher, and it didn't help.

Did you installed the drivers properly ?
Try to reinstall it again. If it still doesn't work maybe you should think about reworking your galletto. :(

[ZetorGumi]

Tried it too, i reinstalled it a several times.
I was trying a Virtual pc, because the fresh installed win7 without drivers run it, and works.

[trotyl]

Maybe sometimes it's not necesarry but I always start "exe's" as ADMINISTRATOR.

[ankjay]

Anyone had the experience on write in a EDC16U34, via OBD?
What was the result?

Thanks! :)

[Suv4x4]

Horray !!!! finally the da vinci code has been cracked. All the credits go to @evisdaci
http://www.digital-kaos.co.uk/forums/showthread.php/505501-FGtech-how-to-fix-this?p=2952041#post2952041


Your problem is USB cable. Change with new one hight quality. To see if your USB cable is OK or not make a test with multimeter. Check the continuity of NEGATIVE in USB cable. Continuity not between wires inside but negative outside. If you see continuity the cable is OK, otherwise your USB cable must be replace. See the photo foolowing :


Check continuity between metalic cover

you know what sir, i want to salute you. You cracked the da vinci code for me. after struggling for 10 days with this tool , making hardware and software changes your suggestion to check connectivity in the outer casing worked. I changed the usb cable and my tool started working

[ankjay]

Hurrayyyyyyyyyyy! :D
In fact, I've used another USB cable... Probably mine was also with issues. :-)

[BoNzOtM]

I have a problem with my fgtech v54 i cannot read obd. Bdm working ok...i have this error.tested obd on 3 cars..what should i check inside

[ankjay]

I have a problem with my fgtech v54 i cannot read obd. Bdm working ok...i have this error.tested obd on 3 cars..what should i check inside

BoNzOtM, have you tried with other protocol, like CAN Line?
If that is with K-Line, probably K-Line of your Galletto is messed up.

[shooting]

Does anyone have the CD for the Galletto4 ?
Mine arrived today and the CD is split in two...

wbr

[azibi130]

I have a problem with my fgtech v54 i cannot read obd. Bdm working ok...i have this error.tested obd on 3 cars..what should i check inside


try changing usb cable

[GTB2260VK]

429115

Hi guys I urgently need some help. I have a Galletto where I am changing some ICs and three SMD caps got lost.
I marked the position in the picture in red, if somebody has the correct values that would be great!

Thanks :single_eye:

[GTB2260VK]

Just figured out that these should be 100uF for decoupling against GND, and that number two in row is not even fitted everywhere.

[ziko]

I cant connect on 2 ecus sid305 renault tricore
Use conenction from fgtech manual, anyone has some usefull info?

Tnx

[Ahmy501]

How to monitor or view .Gal log files with FGtech, is there a way to monitor the process while flashing/reading

[jsg1200]

[Quote = kospoz; 2937052] Mine has also can bus problem by obd but in bootmode can bus is working.If you want to try something pm me [/ quote]

hi.

I changed all to fantomel?s photo.

I can read edc16c3 RENAULT, for bdm port. But i dont can read to bootmode.

Know you where are the problem?

[jsg1200]

Mine has also can bus problem by obd but in bootmode can bus is working.If you want to try something pm me

hi.

I changed all to fantomel?s photo.

I can read edc16c3 RENAULT, for bdm port. But i dont can read to bootmode.

Know you where are the problem?

Regards ;)

[Ahmy501]

I`m having an issue after upgrading my v54 0386 to 0475 i followed the update process as :

Clean delete of fgtech and drivers
-Delete drivers from system32
-Restart
-Install fgtech V54 0475 all win
-Connect device and install drivers from the installation folder
-FTWrite
-Mprog
-program starts but everything is grayed out !!

[Ahmy501]

No hardware rework. is MCU rewrite with LPC2000 a necessity before attempting the above steps ?

[toms4]

No hardware rework. is MCU rewrite with LPC2000 a necessity before attempting the above steps ?

Yes, need update LPC

[shooting]

Does anyone know how to solve this error?

wbr

(Using Windows10 64bit)

[teamtuner]

Does anyone know how to solve this error?

wbr

(Using Windows10 64bit)
anotherwindowsinstall
or,copy that file from another computer where work fgtech to system 32 into this computer
usually it happened when you use same computer with fgtech,vagcom,fvdi...driver conflict

[shooting]

anotherwindowsinstall
or,copy that file from another computer where work fgtech to system 32 into this computer
usually it happened when you use same computer with fgtech,vagcom,fvdi...driver conflict

New install so don't have a working copy, can you provide the file?

thanks :)

[shooting]

Replaced the file with the correct one and still get the same error, I do not think replacing it will solve my problem.
Does anyone know how to fix this? (Windows10 64bit) see pic

wbr

[gazvts]

are you using fantomel's version ?

[shooting]

are you using fantomel's version ?

Yes, do you know what I should do to get it to work?

wbr

[svnsv]

Replaced the file with the correct one and still get the same error, I do not think replacing it will solve my problem.
Does anyone know how to fix this? (Windows10 64bit) see pic

wbr

I got the same Error after updating to 0475.
Writing the "0475_V54_EEPROM" with "FTReadWrite_v3.exe" from Fantomels "FIX&EPT 0475" Folder solved the Problem for me. (Win7 64Bit)

[shooting]

I got the same Error after updating to 0475.
Writing the "0475_V54_EEPROM" with "FTReadWrite_v3.exe" from Fantomels "FIX&EPT 0475" Folder solved the Problem for me. (Win7 64Bit)

I tried that but nothing, thanks

wbr

[ankjay]

Hi everyone,

Like I told you in a previous post, I've managed to read an EDC16U34 with Can-Line through OBD port.
It reads the file, fine.

But since I was curious, I've checked the PCB board of my galletto.

I believe that the LS14 chips needs to be changed, the L9613 and I think there's missing one transistor in C142 position. Am I right?
Also the yellow relays seems to have a good quality but the HUiKE seems garbage. I might consider change it as well.

What do you guys think?

http://oi68.tinypic.com/331dn45.jpg
http://oi63.tinypic.com/2uyg0sw.jpg

Thanks in advance!

[gazvts]

pins round the mcu don't look to good , q18 & q20 missing c142 is cap not transistor 1 of the l9613 looks fake would change both ,try tidy it up

[ankjay]

Thanks gazvts!

Jesus, never realized that Q18 and Q20 was missing. I do managed to read an EDC16U34 from Can-Line... Maybe I was lucky! I will not try, for sure, to write a file with this equipment.
Fortunately, I got a refund from the Aliexpress and with that money I will rework the PCB.

A few things are correct but others, like the L9613 chips and LS14 will definitely change!
Chinese things at best.

[jsg1200]

Hi.
I have my galletto as the one from Fantomel's photo. But with relay AROMAT.


I was able to use BDM, but today it did not work, with some ECU. Probe the voltage source and it's ok. Probe continuity and this is ok.


Could you make a short one inside my galletto?


Thank you. Regards ;)

[bodzio012]

Hi All!
In my galetto v54 computer not see galetto, change usb cable and try other computers and result the same, not start and not see fgtech.
Other galetto on the same cabke usb working ok. What should check?

[mircea13]

ftdi ft232 chip

[jsg1200]

Hi. I need help.

how i made that start bdm?

Regards ;)

[jsg1200]

Hi.
I have my galletto as the one from Fantomel's photo. But with relay AROMAT.


I was able to use BDM, but today it did not work, with some ECU. Probe the voltage source and it's ok. Probe continuity and this is ok.


Could you make a short one inside my galletto?


Thank you. Regards ;)

Hi. I need help.

how i made that start bdm?

Regards ;)

[sahnoun363]

Hi everybody

I have problem on my Galletto V54 lack of communication with the computer in boot mode and via OBD
Someone can help me

Thank you

[JaxMustang50]

Hi everybody

I have problem on my Galletto V54 lack of communication with the computer in boot mode and via OBD
Someone can help me

Thank you

I have the same problem with mine. Trying to clone a BMW Bosch me7.2.

[BoNzOtM]

why i get wake error? what should i change?

[AVDigitale]

hello i have galletto v54 master china clone is working good with bdm jtag ,but i like to read and write vag car edc16u1,edc16u31 and edc16u34 is safe to do this cars over obd port thanks

[AVDigitale]

hi i have china clone galletto v54 but i have problem in bdm is not working how to fix them what need to do to repair in obd2 worked good but just bdm and jtag is not worked what can be problem thanks