PDA

View Full Version : 2013 Ford Ranger Dash



westville locksmiths
8th July, 2014, 08:28 AM
Hi guys what is the best tool for doing km in ford rangers 2013.(24c16)
Digi Prog 3 , Upa or Orange 5 Usb key.
Thanks.

PremierD
8th July, 2014, 08:31 AM
upa .. and a script ...........:) or upa and hexworkshop works as well lol

westville locksmiths
8th July, 2014, 08:43 AM
Thank you Premier D. Is there a tool that can do it Obd.
Or must the Dash come out. Still new at this.

kumistheru
8th July, 2014, 08:59 AM
It's not hard to remove this dash. When you adjust mileage, you need to reset check sum as well. It is safer to program through cluster as you can back it up 24c16 eeprom contents before do any modification to the cluster.

markony79
8th July, 2014, 09:06 AM
here...very fast ..work 100%
S7.39 Ford Ranger, Fusion dashboard programming 2013+ by OBDII (http://www.codecard.lt/carprog/software/carprog-dash/s7-39-ford-ranger-fusion-dashboard-programming-2013-by-obdii/prod_2045.html)

westville locksmiths
8th July, 2014, 09:25 AM
It's not hard to remove this dash. When you adjust mileage, you need to reset check sum as well. It is safer to program through cluster as you can back it up 24c16 eeprom contents before do any modification to the cluster.

Will any programmer do this, where to find km and how to reset cs.
Thank you.

kumistheru
8th July, 2014, 09:39 AM
Yes any eeprom programmer that support read 24c16 chip can be used to do this. Read the chip in 16bit mode. Download this calculator software ( remember to read whole thread) http://www.digital-kaos.co.uk/forums/f174/etsmart-calculators-v1-free-all-407190/

You will find .cal file from HCIP for ford. use that to change the dump you have read from your dash ( Remember to back up you original file). Then change the check sum location of 0526 and 0527 to 00 00. That's it. No fancy programmers needed for this. If you don't know how to do it. Just post your dump and I will adjust you the mileage and post it back to you.

Good Luck

gogalv
8th July, 2014, 12:28 PM
Then change the check sum location of 0526 and 0527 to 00 00.

It is not always, in the calculator to the right is me ORANGE5 CS.


upa .. and a script ...........:) or upa and hexworkshop works as well lol

Compare the UPA and ORANGE5, it's like comparing a bicycle and motorcycle.

PremierD
8th July, 2014, 12:32 PM
upa as a means to read it mate or willem or in fact any eeprom reader.............. you can use a tangerine or a melon for all I care :)

and 00 00 works fine for the complex crc lol

gogalv
8th July, 2014, 12:55 PM
upa as a means to read it mate or willem or in fact any eeprom reader..............


Yes, Ponyprog is The BEST!!!

PremierD
8th July, 2014, 12:57 PM
:roflmao: .... if you say so mate :roflmao:

Apolo29
8th July, 2014, 02:29 PM
I downloaded the etsmart calculator, works ok but i can?t find ranger 2012... with 24c16, is there an script for this vehicle?

westville locksmiths
8th July, 2014, 03:54 PM
where to get usb ?

drpeter
8th July, 2014, 04:30 PM
It is not always, in the calculator to the right is me ORANGE5 CS.



Compare the UPA and ORANGE5, it's like comparing a bicycle and motorcycle.What is orange5? Never heard of it. Is it a secret programmer too good to be true :-).

drpeter
8th July, 2014, 04:36 PM
Hi guys what is the best tool for doing km in ford rangers 2013.(24c16)
Digi Prog 3 , Upa or Orange 5 Usb key.
Thanks. UPA will read it fine with some byte editing.

gogalv
8th July, 2014, 09:24 PM
What is orange5? Never heard of it. Is it a secret programmer too good to be true :-).

I what is TANGO, OMEGA know?

Scorpio-LK (http://www.scorpio-lk.com/eng_index/index.html)

I what is ST92Fxxx, NEC V850ES/SJ3 V850ES/SG3 know?

Calculators to Orange-5 USB (http://pavel-pervomaysk.com/calculators-to-orange5-usb.html)

scip2
9th July, 2014, 03:50 PM
pony prog, upa will do and windows calculator

kennedy-afn
9th July, 2014, 04:00 PM
Hi ! It's right to set Checksum to 00 00 at 526 and 527 address ? Thanks ?

PremierD
9th July, 2014, 04:39 PM
yes.:)...............................

kakaruki
2nd May, 2015, 10:53 PM
why must reset checksum i never heard that you must reset checksum when you programing mileage if you have a calculator.
Is it for this ford ranger car only?

Johnner
2nd May, 2015, 11:06 PM
No,there are other vehicles that this applies to also....If you don't change the Checksum,dash will give you error..

Meat-Head
2nd May, 2015, 11:18 PM
The check sum is the number answer to what the other numbers add to.

theres a cool bit on Wikipedia about check sum states that boat reg numbers have a check sum

Johnner
2nd May, 2015, 11:21 PM
The check sum is the number answer to what the other numbers add to.

theres a cool bit on Wikipedia about check sum states that boat reg numbers have a check sum


Meaty,what you'll find is that every vehicle in the world has a checksum built into the VIN.From memory,it's digit 9 in the VIN.

clusters
2nd May, 2015, 11:51 PM
I didn't know that, well not really, I knew there was a check digit but didn't know it was for checksum. Any idea how it's calculated, or is it just a sum?

Johnner
2nd May, 2015, 11:58 PM
No,it's based on weighted tables,involving the whole vin sequence.I used to know how to work it out,but couldn't be arsed anymore.

Meat-Head
3rd May, 2015, 12:14 AM
OFF TOPIC:-

look for a thread by fallen vin decoder then go play with yourself

kakaruki
3rd May, 2015, 11:09 AM
i do odometer correction via eeprom and calculator and i never have to correct checksum i dont know what you mean.

kennedy-afn
3rd May, 2015, 03:03 PM
Hi guys what is the best tool for doing km in ford rangers 2013.(24c16) Digi Prog 3 , Upa or Orange 5 Usb key. Thanks. Hi ! I have X-Tool. It can do by OBD or 24c16. Thanks !

justy22
3rd May, 2015, 07:06 PM
OFF TOPIC:-

look for a thread by fallen vin decoder then go play with yourself

GET some toilet paper and wipe the ***** away from yer chin

gui2015
2nd November, 2015, 07:58 PM
hola amigo me pasas el scripts para la ranger

hugos31
6th January, 2016, 02:03 PM
Yes any eeprom programmer that support read 24c16 chip can be used to do this. Read the chip in 16bit mode. Download this calculator software ( remember to read whole thread) http://www.digital-kaos.co.uk/forums/f174/etsmart-calculators-v1-free-all-407190/

You will find .cal file from HCIP for ford. use that to change the dump you have read from your dash ( Remember to back up you original file). Then change the check sum location of 0526 and 0527 to 00 00. That's it. No fancy programmers needed for this. If you don't know how to do it. Just post your dump and I will adjust you the mileage and post it back to you.

Good Luck
please share calculator software

2016nicaragua
2nd February, 2016, 03:45 PM
HOLA CUANTO VENDE ESO SCRIT GRACIAS

antenor
12th March, 2016, 10:32 PM
363402 Script ETsmart can do it!!!
If you need i give you de script .CAL

antenor
12th March, 2016, 10:43 PM
ETsmart script to FORD RANGER 24c16 2013. :biggrin:

Johnner
12th March, 2016, 10:50 PM
Antenor,I have a dumbass question for you.....Why are you passwording that script...when it's common knowledge now... ???

And also...you've been here 6 years,only started posting this year,and you still haven't introduced yourself...

Please do so here : Introduce Yourself


(http://www.digital-kaos.co.uk/forums/forumdisplay.php/2-Introduce-Yourself)

jomberykaso
13th March, 2016, 01:58 AM
ETsmart script to FORD RANGER 24c16 2013. :biggrin:


..................:roflmao: