Dawiww
10th October, 2015, 11:38 PM
Hi everyone!
My name is Dave, and I'm writing to you from Poland :)
I tried to make a retrofit from halogen headlights to OEM Xenon headlight.
So: I got 2x headlights ( 5G1941034 - Right, 5g1941033 - Left), with single lens and shutter, AFS, Cornering Lights, one U-LED and small LED dot in inner part of headlight. Modules arleady mounted.
Pins available in Halogen Lamp:
1,2,3,4,5,6,8,9,7 and 10 was empty
Pins available in Xenon Lamp:
1,2,4,5,6,7,8,9,10,12, 3 and 11 was empty.
Then I remake wiring, based on PDF from VW about connections in Xenon lamps and Halogen lamps:
Left lamp:
Cut Halogen Pin (1) 12V
Cut Halogen (2) and (3) - Headlight regulation
From Halogen (4) - DRL/Parklight make Xenon (12) U-Led because they should be connected to that same pin in BCM (4)
From Halogen (5) - Ground make Xenon (5) and (7) Ground because they both should be Ground
From Halogen (6) - Low Beam make Xenon (6) Low Beam because they should be connected to that same pin in BCM (5)
From Halogen (8) - High Beam make Xenon (8) High Beam because they should be connected to that same pin in BCM (39)
From Halogen (9) - Blinker make Xenon (9) Blinker because they should be connected to that same pin in BCM (36)
From BCM (10) make new wire to Xenon (10) for U-Led (Second wire - that's weird..)
Connect 12V from Fuse C37 to Xenon (4)
Also make Can H and L on (1) and (2) Pins in Xenon
Right Lamp:
Cut Halogen Pin (1) 12V
Cut Halogen (2) and (3) - Headlight regulation
From Halogen (4) - DRL/Parklight make Xenon (12) U-Led because they should be connected to that same pin in BCM (32)
From Halogen (5) - Ground make Xenon (5) and (7) Ground because they both should be Ground
From Halogen (6) - Low Beam make Xenon (6) Low Beam because they should be connected to that same pin in BCM (1)
From Halogen (8) - High Beam make Xenon (8) High Beam because they should be connected to that same pin in BCM (2)
From Halogen (9) - Blinker make Xenon (9) Blinker because they should be connected to that same pin in BCM (20)
From BCM (10) make new wire to Xenon (10) for U-Led (Second wire - again)
Connect 12V from Fuse C36 to Xenon (4)
Also make Can H and L on (1) and (2) Pins in Xenon
After that Xenon flickers, U-Led doesn't even try to light up, and when I try to turn high beams, they turn on thats Led dots :D So signal going from BCM as high-beam-on-signal heading to Xenon pin responsible for Dot DRL. Only Blinkers seems to work fine.
So.. Coding, I think.
I find two pages about that, on others sites..
.. and looking on that second page "Anatomy of Leuchte" page Socket Pins numbers seems correct. Blinkers are in plug B Pins (36) and (20), Parking lights on (10) and (21), DRL on (4) and (32), Low beams on plug C (5) and plug B (1), High Beams on (39) and (2). Hm.. Shutters? Looks like they should be connected to (23) and (22). But... My PDF infromed me, that High beams should be on (39) and (2) in BCM. I have also one more PDF. After deep analisis I found that there is shutter connected to (23) and (22) BCM - But they need to connect to Xenon (11) which is absent..
After Coding from these Two pages:
- U-Led start Working, but only if there is signal on (10) and (12) pin in Xenon - need to code Leuchte2,3,4,5 for them to work. Change Leuchte 8 and 9 from High beams to work as DRL LED-dot. Code Low beams to work as Xenon.
Now have working Blinkers and Fog lights - they work all the time and was in car from beginning. Xenon low beams works fine, U-LED and DRL LED dots also works fine. Doesn't work Auto light mode (I got sensor behind mirror - I don't know it's light or rain sensor) and there wasn't be DRL when switch is on 0 position. High Beams doesn't work :( AFS too..
And from another shelf: How to calibrate Steering angle Sensor? I got a error and there came a lot errors on the car network :/
How to reset TPMS? Is this option sould be on Infotainment Car-menu? I does'n have that option and that tire presure warning still on dashboard :/
Anyone can help me somehow? Any advices? Thank you in advance!
My name is Dave, and I'm writing to you from Poland :)
I tried to make a retrofit from halogen headlights to OEM Xenon headlight.
So: I got 2x headlights ( 5G1941034 - Right, 5g1941033 - Left), with single lens and shutter, AFS, Cornering Lights, one U-LED and small LED dot in inner part of headlight. Modules arleady mounted.
Pins available in Halogen Lamp:
1,2,3,4,5,6,8,9,7 and 10 was empty
Pins available in Xenon Lamp:
1,2,4,5,6,7,8,9,10,12, 3 and 11 was empty.
Then I remake wiring, based on PDF from VW about connections in Xenon lamps and Halogen lamps:
Left lamp:
Cut Halogen Pin (1) 12V
Cut Halogen (2) and (3) - Headlight regulation
From Halogen (4) - DRL/Parklight make Xenon (12) U-Led because they should be connected to that same pin in BCM (4)
From Halogen (5) - Ground make Xenon (5) and (7) Ground because they both should be Ground
From Halogen (6) - Low Beam make Xenon (6) Low Beam because they should be connected to that same pin in BCM (5)
From Halogen (8) - High Beam make Xenon (8) High Beam because they should be connected to that same pin in BCM (39)
From Halogen (9) - Blinker make Xenon (9) Blinker because they should be connected to that same pin in BCM (36)
From BCM (10) make new wire to Xenon (10) for U-Led (Second wire - that's weird..)
Connect 12V from Fuse C37 to Xenon (4)
Also make Can H and L on (1) and (2) Pins in Xenon
Right Lamp:
Cut Halogen Pin (1) 12V
Cut Halogen (2) and (3) - Headlight regulation
From Halogen (4) - DRL/Parklight make Xenon (12) U-Led because they should be connected to that same pin in BCM (32)
From Halogen (5) - Ground make Xenon (5) and (7) Ground because they both should be Ground
From Halogen (6) - Low Beam make Xenon (6) Low Beam because they should be connected to that same pin in BCM (1)
From Halogen (8) - High Beam make Xenon (8) High Beam because they should be connected to that same pin in BCM (2)
From Halogen (9) - Blinker make Xenon (9) Blinker because they should be connected to that same pin in BCM (20)
From BCM (10) make new wire to Xenon (10) for U-Led (Second wire - again)
Connect 12V from Fuse C36 to Xenon (4)
Also make Can H and L on (1) and (2) Pins in Xenon
After that Xenon flickers, U-Led doesn't even try to light up, and when I try to turn high beams, they turn on thats Led dots :D So signal going from BCM as high-beam-on-signal heading to Xenon pin responsible for Dot DRL. Only Blinkers seems to work fine.
So.. Coding, I think.
I find two pages about that, on others sites..
.. and looking on that second page "Anatomy of Leuchte" page Socket Pins numbers seems correct. Blinkers are in plug B Pins (36) and (20), Parking lights on (10) and (21), DRL on (4) and (32), Low beams on plug C (5) and plug B (1), High Beams on (39) and (2). Hm.. Shutters? Looks like they should be connected to (23) and (22). But... My PDF infromed me, that High beams should be on (39) and (2) in BCM. I have also one more PDF. After deep analisis I found that there is shutter connected to (23) and (22) BCM - But they need to connect to Xenon (11) which is absent..
After Coding from these Two pages:
- U-Led start Working, but only if there is signal on (10) and (12) pin in Xenon - need to code Leuchte2,3,4,5 for them to work. Change Leuchte 8 and 9 from High beams to work as DRL LED-dot. Code Low beams to work as Xenon.
Now have working Blinkers and Fog lights - they work all the time and was in car from beginning. Xenon low beams works fine, U-LED and DRL LED dots also works fine. Doesn't work Auto light mode (I got sensor behind mirror - I don't know it's light or rain sensor) and there wasn't be DRL when switch is on 0 position. High Beams doesn't work :( AFS too..
And from another shelf: How to calibrate Steering angle Sensor? I got a error and there came a lot errors on the car network :/
How to reset TPMS? Is this option sould be on Infotainment Car-menu? I does'n have that option and that tire presure warning still on dashboard :/
Anyone can help me somehow? Any advices? Thank you in advance!