Renault Sirius 32 wiring

[shooting]

Hi everyone,
I'm trying to read a Sirius32 on the bench using a Galletto 1260 Via OBD2 and have made this,
it doesn't seem to work, can someone tell me if I'm missing something?
I'm using a 2amp 12v supply
I get "Linking Error"

wbr :)

[morfej]

I guess u want to read it in boot mode ... than u are missing the boot pin on flash pin 28.

br

[shooting]

I guess u want to read it in boot mode ... than u are missing the boot pin on flash pin 28.

br

I added the boot pin with 1k ohm and tried without too, I think it's my wiring that's wrong

wbr

[ttzag]

3--ecu weight gnd
30--12+
29--12+ switchable
56-- K-line
boot -- pin 28 on flash

[shooting]

3--ecu weight gnd
30--12+
29--12+ switchable
56-- K-line
boot -- pin 28 on flash

Pin 28 on flash to ground with 1k ohm ?

wbr

[ttzag]

i read it without res
pin 28 connected to boot wire from fgtech

edit : sorry you need to read it by OBD?

[shooting]

i read it without res
pin 28 connected to boot wire from fgtech

edit : sorry you need to read it by OBD?
I'm using Galletto 1260 OBD cable :)

wbr

[ttzag]

oh ... i miss your tool sorry . i dont think you can read it by OBD but you can try

[shooting]

oh ... i miss your tool sorry . i dont think you can read it by OBD but you can try

It reads in the car so should be ok on the bench?

wbr

[ttzag]

you read on the car without boot pin or with ?

[shooting]

you read on the car without boot pin or with ?

Without, but only get eeprom.
Is Pin 28 to ground with 1k Ohm ok for Boot?

wbr

[ttzag]

i connect pin 28 to boot wire on fgtech cable without resistor 1 k ohm.
if you read it on car with ,, so you have to solder one on bench

[shooting]

i connect pin 28 to boot wire on fgtech cable without resistor 1 k ohm.
if you read it on car with ,, so you have to solder one on bench

Just boot pin to ground?

wbr

[ttzag]

how did you install resistor when you read it on the car ?

[shooting]

how did you install resistor when you read it on the car ?

I did not try on the car with Boot, only read with cable in OBD.
In the car can read, on the Bench "Link Error"

wbr

[morfej]

You did not read eeprom over obd... no way with Galletto 1260.

What exactly u want to do ?

[ttzag]

try pin 28 with res on ecu weight

[shooting]

You did not read eeprom over obd... no way with Galletto 1260.

What exactly u want to do ?

I want to read all Flash not just eeprom, and on the bench.

Here is dump from car with 1260 and Picture of software to show you

wbr

[shooting]

try pin 28 with res on ecu weight

What is "weight" .. I'm new to reading ecu's

wbr

[ttzag]

What is "weight" .. I'm new to reading ecu's

wbr

Weight =ground, Ecu body


Sent from my iPhone using Tapatalk

[Jan1980]

Is your flash in ecu 29f200bb or 29f200ab ??? You can just read 29f200bb in bootmode. If you have 29f200ab, you have to desolder flash chip and read it with programmer..


Gesendet von iPhone mit Tapatalk

[shooting]

Is your flash in ecu 29f200bb or 29f200ab ??? You can just read 29f200bb in bootmode. If you have 29f200ab, you have to desolder flash chip and read it with programmer..


Gesendet von iPhone mit Tapatalk
Thank you but this is not my question, see Post 1 for question...

wbr

[Jan1980]

Yes, i know... but if you ecu has 29f200ab.. you can never read.. and not with 20$ galetto 1260..


Gesendet von iPhone mit Tapatalk

[shooting]

Yes, i know... but if you ecu has 29f200ab.. you can never read.. and not with 20$ galetto 1260..


Gesendet von iPhone mit Tapatalk

I already read, no problem....and my cable is not Chinese copy....

wbr

[Jan1980]

Ah ok. Sorry, i thought chinese.. what's your solution ?


Gesendet von iPhone mit Tapatalk

[shooting]

Ah ok. Sorry, i thought chinese.. what's your solution ?


Gesendet von iPhone mit Tapatalk

In the car OK, but on the bench "Link Error"
Any solution?

wbr

[mrchip]

your wiring up looks good, I read it too in the same way , but with galetto v54

sirius 32 cant be read in bootmode,,, sirius 32N can be read ( by galetto )

[shooting]

your wiring up looks good, I read it too in the same way , but with galetto v54

sirius 32 cant be read in bootmode,,, sirius 32N can be read ( by galetto )

For me I think the ecu I'm using is faulty (Link Error)
but am told this should read in Boot mode no problem :)
I made this boot pin with 1k ohm and switch to try..

wbr

[mrchip]

ok, galetto ori are then very good, I had never succes with sirius 32 in boot mode with clone v54 ( 32N is no problem )

[shooting]

SIRIUS32
======
Can someone tell me what is in the Eprom (Emulated) and what is in the Flash? (256k) .. Immo, maps.. etc..
Can the ecu be tuned from eprom?

wbr

[shooting]

Solved.

Remapped 32k OBD file using WinOLS with .KP Map Pack, Runs VERY well..!!
If anyone wants a Sirius32 remapped then all you need is the 32k file read with a Galletto 1260, really simple :D

wbr