volvo v70 swap airbag units . is possable ?

[smirnoff_rules]

l have this unit can you tell me if l can swap eeprom to use secondhand unit ? l what one

https://i.gyazo.com/b87143b2a1b0b74fcb9f6b9a2a3e12fc.png

https://farm6.staticflickr.com/5666/30841217646_5254468bb2_z.jpg


cheers lads

[FxShaw]

Swap / clone CR16MCS9V its up to you.

[smirnoff_rules]

sorry m8 wheres CR16MCS9V

is that on the back of the board then ?

[credoline]

Yes, but if you have Carprog, he can do it this module trough K line, to clear crash data, not sure about r/w. Module connection:
pin 55 +12V
pin 83 GND
pin 31 K line
For this connection i am not sure 100% but you can check it easy.

[smirnoff_rules]

l have xprog l just looked and l see l can read it , the board is tight in there tho might need to heat it up l think , never stripped one


can you see where these pins are
pin 55 +12V
pin 83 GND
pin 31 K line

as the pins are not numbers and xprog picture dosnt say alot

https://i.gyazo.com/09d4c102c01dfb42beb601d416812175.png

[credoline]

XPROGM support only 80 pin CR16, what if is with 44 pins ?
UPA USB support both of them but never hear that someone is read good part of memory in CR16 with 44 pins.

[FxShaw]

Should be on the other side of the board.

[smirnoff_rules]

ITS 80PIN took off and tried to read as its off but no luck ? will swap it on to new unit when it comes and see

https://i.gyazo.com/e6a4966311fefde99e3c6744001daf20.png

https://i.gyazo.com/c27aaaf7da9db83d3d45b2062a27b657.png

any idea what this error

[credoline]

When MCU is in module, you can read/write MCU via K line of module, and you need to connect +12V, GND and K line to airbag module and one pin of MCU need to put in boot (pin 13 of MCU). As is in XPROGM described. You CAN NOT read MCU out of board because of bla, bla...
With XPROGM hardware you are receive K line adapter, marked with this numbers 1-002-0007. This adapter you use for this situation.

[smirnoff_rules]

yea l have that but wasnt clear what pin on ecu is kline

do you know the pin numbers m8 and the side you count from . theres no pin numbers on airbag ecu

[smirnoff_rules]

yea l have that but wasnt clear what pin on ecu is kline

anyone know the pin numbers and the side you count from . theres no pin numbers on airbag ecu

anyone ?...........................

[credoline]

Try to compare with this information.

[smirnoff_rules]

great , so do you think red/white is power ? black earth ? and the blue kline ?

cheers for your help m8

https://i.gyazo.com/306ca5adc0f95746ada0bfed1fecc475.png

[FxShaw]

That sounds about right...pin 55 12v pos red/white, pin 83 gnd, pin 31 kline blue

[smirnoff_rules]

my pins are different to that .. think lm winner then go back to last place again lol
connect to pin number but still get boot error lm have soldered to legs havnt got my copper wire here to clean up

https://i.gyazo.com/a7a3f6654e7ad991523836148c01bcaa.png



just realized l didnt read the number right this is a different kline thing ....
think l will just swap chip when other unit comes

https://i.gyazo.com/ee257eea48be0eba02f0ddd668516d76.png

does say modb on it tho ?

[credoline]

Yes, this pin MODB is used to put MODB on Motorola MCU HC11EA9 to ground in BMW EWS3. Here you can use it to put pin 13 ENV0 to the ground, or simply solder this pin on board short to GND.
Same thing.
And now when you are pulled out this airbag board, with om meter (mess.instrument) you can find pin 13 of CR16 MCU on other side of board and make it a good picture and upload it here, so next time is not necessary to open module that deep.

[smirnoff_rules]

do you think that a dump from a used ecu can be edit to work on this car ? or do l still need to get a dump of this one here ?

https://i.gyazo.com/2054d5fccf0d6d63dbe3d09dd3c30467.png

[credoline]

I want that you show me where is line to pin 13 on that side of board on yours picture.
I see that is this little complicated for you. If the initially problem with yours original module was hardware nature,
just replace CR16 from one module to another one and finish job. But if problem is in crash data, you must read/write this MCU

[credoline]

You see in PDF document, i send you here, on page 7, second picture ? There is wire, this wire make a short between ground and pin 13 of MCU.
And yours picture and this picture looks to me similar.
Not the same, but similar.

[smirnoff_rules]

complicated ...yea lol , to old for new tricks lol hammers and spanners me