Toyota Sequioa 2007 Virgin file

[eepromRipper]

Hi, I have a Toyota sequioa 2007 with no key, i have read the immo-box with part number 89780-34010 and a 93LC66 eeprom.(attached) i have tried to delete the key inside the eeprom to see if it will become virgin but to no avail, PLS i need a virgin file from the attached file. or any other way of programming. thank you.

[AUS-MAN]

Hi, I have a Toyota sequioa 2007 with no key, i have read the im*o-box with part number 89780-34010 and a 93LC66 eeprom.(attached) i have tried to delete the key inside the eeprom to see if it will become virgin but to no avail, PLS i need a virgin file from the attached file. or any other way of programming. thank you.

eepromRipper you can reset most Toyota 4D systems via the OBD port. Tools like AD100/MVP/T300 etc or the Toyota quick reset dongles will reset the system for you. On some Toyota models the im*o box is located deep under the dash and takes a lot of labour to remove. So it?s probably worth investing in a tool to reset via the OBD port if you work on a few Toyotas.

Good Luck

[ray-ray]

if you reflash the immo. you have to do a 30min. synchromizion by ground out pin 4 & 13 these will marry the ecu to the immo.so if the immo. light turn off but won't start you have to do the 30min. deal.

[eepromRipper]

thanks for your contribution, this model of toyota does not reset without a master key, so i need the dump from a brand new immo-box of the same part number.

[AUS-MAN]

None of the tools i listed need a masterkey present.

[eepromRipper]

those tools can't connect to a 2007 sequioa. i've tried ad100 and t300.

[AUS-MAN]

Sorry about the bum steer epromRipper. You are right AD lists only 01-02 models.

[impactops]

I believe the carman scan tools by nextech do

[impactops]

When you say you have tried to delete the key from the eeprom, which memory location(s) & what value? "FF"

[Tech_SOS]

No tools will reset this immobilizer via OBD. This is like the older Toyota that must be reflashed or replaced when keys are lost. This member needs a virgin file, that is the only solution on Sequoia up to 2007.

[eepromRipper]

When you say you have tried to delete the key from the eeprom, which memory location(s) & what value? "FF"
yes i put FF in the address where keys where stored. i guess i need the dump from an unused toyota sequoia immo box

[impactops]

Just out of curiosity eepromripper, have you tried blanking the whole eeprom with "FF" just to see what happens?

[cjawahir]

hi this is a virgin dump , for toyota 4d .

cj

[impactops]

hi this is a virgin dump , for toyota 4d .

cj
Attached Fileshttp://www.digital-kaos.co.uk/forums/images/styles/digital/attach/zip.giftoyota_landcruiser_93lc66.zip (http://www.digital-kaos.co.uk/forums/attachments/f115/12362d1267106133-toyota-sequioa-2007-virgin-file-toyota_landcruiser_93lc66.zip) (178 Bytes, 1 views)
Last edited by cjawahir; Today at

File appears to be corrupt

[cjawahir]

you have to unzip and open the file , i just download it and it look ok to me .

cj

[ngakson2002]

Dear friend,
I am serge Ngako head of Department of the automobile engineering workshop at one of the Government Technical and Vocational School here in Cameroon.

As i used to explain in this forum, i have a key programming tool that program transponder key just from IMMO DUMP.

This said, from your 93LC66 dump from your IMMO BOX, i have already program a key here ready to start your Car (The key is a 4C transponder chip key, with the TIRIS NUMBER:7E B1 3B B2 6B 00 6B 00 00 8D 07 7E) and what you will just need will be to cut the blade to suit your ignition switch.

I can then help by sending to you this key if you can take care of the shipping charges via DHL from Cameroon to your Country.

Here you have two options:

1) i can just send the program transponder chip that you will need to fit it in a key or

2) i send both transponder with key

If interested, send me your complete address via my email box

ngakson2002@yahoo.com

best regards

[eepromRipper]

hi this is a virgin dump , for toyota 4d .

cj

i will try this and let you know.

[eepromRipper]

Dear friend,
I am serge Ngako head of Department of the automobile engineering workshop at one of the Government Technical and Vocational School here in Cameroon.

As i used to explain in this forum, i have a key programming tool that program transponder key just from im*o DUMP.

This said, from your 93LC66 dump from your im*o BOX, i have already program a key here ready to start your Car (The key is a 4C transponder chip key, with the TIRIS NUMBER:7E B1 3B B2 6B 00 6B 00 00 8D 07 7E) and what you will just need will be to cut the blade to suit your ignition switch.

I can then help by sending to you this key if you can take care of the shipping charges via DHL from Cameroon to your Country.

Here you have two options:

1) i can just send the program transponder chip that you will need to fit it in a key or

2) i send both transponder with key

If interested, send me your complete address via my email box

ngakson2002@yahoo.com

best regards

m8, this a 4D key not 4C with the tiris you wrote. if you have suggestion put it here so others can learn not emails. thanks for your assistance.

[eepromRipper]

I tried the Land Cruiser Virgin file, the immo light stay on but when u insert a key, the it stays lit for 3 secs then starts blinking double instead of going off. I guess i need the original Toyota Sequoia 2007 Virgin dump.

[shitad]

You need 4D 67 to do this job. After reflash put new keys in for 5 seconds without turning key on, then close programing mode by puting in the 1st key and turn ignition on 5 times in 5 seconds. Ather this you must leave key on and re-initialize the ECU and the IMMO which takes 30 minutes.

[eepromRipper]

I will try today and let u know.

[sogaro]

Did it work?

[eepromRipper]

perfectly!

[Moyshe]

Im having trouble opening this virgin file. i need the bin file please thank you.

[pintudex]

you have to unzip and open the file , i just download it and it look ok to me .

cj
hi there,
try with ezflasher! its a great tool. and will do al your reflash work.

[ngakson2002]

Dear

I do not have the virgin file corresponding to this immo dump.However, i can help you by written key logic (data) directly in your dump posted. once send to you copy the modify dump in your immobox memory device and then start your car straight foward.
This said,your dump posted reveals that the car was using a 4D - 67 transponder.What i will then need in order to help you is the key logic from a 4D -67 transponder that you will read with a transponder reader and post it to me via ngakson2002@yahoo.com
Please read once more the original data that was in the 93Lc66 and post along.
Awaiting for your reply in order to help you

Serge

[ngakson2002]

Dear

I do not have the virgin file corresponding to this immo dump.However, i can help you by written key logic (data) directly in your dump posted. once send to you copy the modify dump in your immobox memory device and then start your car straight foward.
This said,your dump posted reveals that the car was using a 4D - 67 transponder.What i will then need in order to help you is the key logic from a 4D -67 transponder that you will read with a transponder reader and post it to me via ngakson2002@yahoo.com

Awaiting for your reply in order to help you

Serge