dreambox 800 se ERR01 NO CA FOUND hellp

[mike d]

can anyone help I get this message (no ca found)in lcd screen tryed dreamup serial way try flashing but i get this message to much data or bad sectorsin partion 1 (end:00040000,pos:00040000)i'm using dm800se 82 210 sim

[alom5]

can anyone help I get this message (no ca found)in lcd screen tryed dreamup serial way try flashing but i get this message to much data or bad sectorsin partion 1 (end:00040000,pos:00040000)i'm using dm800se 82 210 sim

read the thread again mate....page 3. it's all on there.

you need SUNRAY and not dreamup for 800se.

[meme10]

hi, i had ssl84 (sim 210) and after un upgrade to open pli unpatched dm 800se does not boot. Dreamup 1.3.3.9 or Sunray 1.3.3.7 does not recognize the box (nothing happend when power up the box). What can be done? Thank you.

[meme10]

Hi,
I discovered that i have a hardware issue.
Actualy my system is DM800HD se, it has mini usb. I discovered what was wrong. My Silab usb to serial adapter (which is on board of DM800se) does not work properly(even if it is correctly discovered by win 7). I was not able also to use null cable (i connected the wires directly on board after Silab CHIP) and ethernet with Sunray. But after a few hours of trying i discovered that when connecting only TX from my serial port to RX on the SILAB chip system continue to boot after CA NO FOUND ERROR. After that (1-2 seconds) i unpluged this wire and push the front button to stop into http mode. I don't know if this is working only on my defective board. Using this method i was able to boot original image. Thanks for help. It will be nice for somebody with a non defective board to test my method.

[simazambrosso]

look this my friend

Fix: No CA Error

[gemihema]

Quick tut to repair NO CA on all DM800HD

Please use patched version Dreamup

1. connect via serial using NULL Modem cable and Ethernet to router and pc.. ( if you don't have a Null modem cable you can purchase here null modem cable found EDITED.. ANYWHERE

2. load patched version of dreamup, select your com port and then click connect and power on dm800

3. when initialised it will display http serial mode on lcd and show dhcp ip once ip is displayed dreamup as served its purpose and now its in flashmode

4. log into webshell on pc using the 192.168.x.xxx address on LCD disply and flash as normal

[oneleginto]

The DM800SE No CA Fix:

1. Download Sunray Flasher here (for DM800SE and DM500HD with Sim 2.1)

2. Download the Second Stage Bootloader Here Hotfile.com: One click file hosting: sim2SE_SSL82_110620.nfi It will fix the no Ca found message.

3. Open Sunray flasher and connect via USB Mini (and use network mode for faster flashing) to your dm800se. Flash the .nfi SSL 82 bootloader file.

4. Turn off box. Now hold the front standby button and power on. Open the DHCP IP in your browser and flash any image of your choice.

5. IMPORTANT: Repeat Step 3. Now your done!

Note 1. I find i cant flash an image using sunray flasher, so thats why i used the browser method.
Note 2. If you don't get a DHCP IP, put your router IP to 192.168.0.1
Note 3. Use Internet Explorer to flash. FF4 wont work

dantheman06 God I love you thanks..

[johnnyboy78]

I flashed my Dreambox 800hd and now it does not even boot it shows No CA error with no IP address

[johnnyboy78]

I flashed my Dreambox 800hd and now it does not even boot it shows No CA error with no IP address

Even when i use dream up nothing happens any more

[total newby]

yeah
i am just looking for good image for it now i tried lot of them didnt work

i like this one- Nemesis2-6-dm800se-SVN-110r0-ramiMAHER.nfi , iv tryed every hdse image on here some worked better for my se than others but this is a good one its in the downloads section

[chic.]

Even when i use dream up nothing happens any more

hi m8 welcome to the forum
use sunray flashup a null modem cable and a network cable untick the use network click connect switch box on when connected click flash scroll to your image click on it and it will flash to the box