Flashing DM800 problem!

**network-nt** · 9th April, 2010, 12:17 PM

Originally Posted by westkill

not 100% sure
this version worked for me on a clone i think

It worked a treat! Many thanks!

**av2008** · 9th April, 2010, 01:41 PM

Originally Posted by flagooner

Hi please help me I am completely new to this I have read everthing I could about flashing a Dreambox 800 and when I try to flash I get the same problem as Reloaded ie " is not a valid integar value" I don't undrestamd Kevin's instructions clearly I am an idiot but which cable do I connect to the DM800? and select IP is not available.Please can someone help me, thank you

Basically open up that software that Kevin has supplied in his second post (Dreambox enforcer). Once you do that you have to connect the DM800 to a pc with a null modem cable (RS232 cable) whilst the DM800 is off. Then click connect on the software and turn on the DM800 from the mains.

The null cable goes into the COM port of a pc, if you have a laptop you can use a null to usb cable.

**francoarab** · 20th April, 2010, 10:56 PM

thx man i ll try to see if works

**kadnor** · 23rd April, 2010, 09:32 AM

[

Hi KEVIN,

I would be most grateful if you would kindly study the possibility of helping me in the correct parameters to utilize in order to
get some channels from Sat Eu W2M @ 10*EAST.

The C band channels are 3927 R 8300 5/6 8PSK,
I Can manage from SET UP to Service searching.
4 days struggling to get these channels,I come to the conclusion that my prescan parameters are not correct, they generate a SNR 0 , AGC 93 ( signal not locked)

Wish to have a few tips how to proceed from SET UP in order to do it correctly and receive these channels. Am utilising a SATLOOK for precise pointing of 10*E/ele.

Many thanks in anticipation for your assistance.
Best Wishes,
yours respectfully,

kadnor

=kevin64;441874]hi
what you have to do
1-run dreamup , connect DM800 with cable
2- under dreamop select network and in the remote ip (box) put the ip you want for your box
3-now switch on the dreambox, dreamup will prepared the box for flash
when ready for flash
4 take the remote ip (box) then follow the procedure through the web now
192,168.xxxx.xxx
will get to the upgrade firmware page

This will force the box on bootloader mode

I hope this will help[/QUOTE]

**cirrus** · 26th April, 2010, 08:26 AM

i have the same problem and i hope it work with me

**enalaprin** · 6th May, 2010, 11:05 AM

Originally Posted by reloaded

Kev

tried the enforcer mate, but now i keep getting ''file too big''
when i select flash to upload the nabilo image....

is my box knackered?

only had it for 2 days!

For me too appears "file too big"
Tell how to solve this problem please??

**richies** · 12th May, 2010, 12:36 PM

DreamUp Mod recongnises the DM800S and shows that it flashes the box. When I enforce flashing an image afterwards, the progress bar is also indicating that it works fine. But after flashing I always have the same problem:
DM800S strats with "Dream Multimedia", the red lamp switches off after ca. 0.5 sec and thats it - nothing happens. Does anyone had the same problem and found a solution to it?

**abualferas** · 13th May, 2010, 08:22 AM

same thing but no ethernet light in the back of the receiver

**fish77** · 13th May, 2010, 03:05 PM

Originally Posted by richies

DreamUp Mod recongnises the DM800S and shows that it flashes the box. When I enforce flashing an image afterwards, the progress bar is also indicating that it works fine. But after flashing I always have the same problem:
DM800S strats with "Dream Multimedia", the red lamp switches off after ca. 0.5 sec and thats it - nothing happens. Does anyone had the same problem and found a solution to it?

what image are you trying to flash it with?

**dreamboy** · 21st May, 2010, 08:38 PM

I am a newbie - tried dreamup 1.3.3.5 on my dm800 clone, shows msg "uploading flash-loader" for about a minute and the OLED says DreamMultimedia. When 100% complete DreamUP shows "upload completed, waiting for acknowledge..." and DM800 restarts but comes back with "No CA found". On Dreamup the Flash button never gets enabled.

pls help!

**bubbles69** · 21st May, 2010, 08:51 PM

you killed it dreamup is only for repair bad flash you use webshell to flash dm800, you mus use the dreamup patched version i posted a few weeks back, that will put box back in flash mode so you can flash via web shell..

**boogie** · 21st May, 2010, 10:28 PM

Originally Posted by bubbles69

you killed it dreamup is only for repair bad flash you use webshell to flash dm800, you mus use the dreamup patched version i posted a few weeks back, that will put box back in flash mode so you can flash via web shell..

sorry to butt in...
so what if the box just doesnt take the flash(cable is good) and doesnt allow webshell edit?...what then?bad sim?i never got either of the two most usual messages via dreamup: no ca / integer..
the progress bar doesnt move.
any ideas appreciated

**bubbles69** · 22nd May, 2010, 07:10 AM

what happens when you try and connect to dreamup with using the patched version, does it see the dm800?

**boogie** · 22nd May, 2010, 09:24 AM

Originally Posted by bubbles69

what happens when you try and connect to dreamup with using the patched version, does it see the dm800?

hi bubbles
yeah,no version of dreamup seems to connect(com ports and cable are fine/tested working).in the bottom status bar it never shows up as connected..pulling hair out !