[hole]

need help to change language to my bmw how to change languages ???

[hole]

bmw320i.........help me...........

[racin-snake]

can you explain what you want to change the language in ? the dash the instruments ect .and what language you want to change from and to ?

[hole]

i want change lenguage in the dash the instruments deutschland to italian...... tank you

[smirnoff_rules]

here the service and manuals that came with the car , Find user guide for BMW - Diplodocs

[hole]

tank's but,i have the manual.the information there isn't

tank's for the web site

[smirnoff_rules]

RESETTING THE BMW DASH LANGUAGE
The language is stored in the Coding Plug. This is located in chocolate-brown harness connector
on the back of the instrument cluster. After 2/89 this is a separate plug on the back of the cluster.
When the cluster is first powered up the language is normally German by default.
To change the language,
1. Ignition switch in the OFF position.
2. Press and HOLD the right instrument cluster button.
3. Turn the ignition switch to the on position.
4. Wait about 10 seconds. The next language will be displayed.
5. Hold the button until the desired language appears.
If the language doesn't hold one of the following has occurred:
a) Code Plug has bad connection. - Check wiring for breaks or shorts. Disconnect and then
reconnect the Coding Plug on the back of instrument cluster.
b) Coding Plug may be defective. Replace Coding Plug.
c) Instrument cluster motherboard is dead. When this is the case there are normally other
problems present, such as : jumpy needles, tripometer resets itself to zero, gong keeps
sounding even after the brakes are depressed,...etc.
E36 OBC V The test function are accessed by pressing the "1000" and
"10" buttons simultaneously. Test function(1,10,18,19,& 21) are unlocked and
can be called up by inputting the number and pressing " SET/RES" Number 10
is Language change.
BC V TEST FUNCTIONS
The BC contains test data values that can be accessed for troubleshooting
purposes. The
following is a list of the test functions and numbers that are stored in the
BC
1. Display test - test all of the LCD segments in the display matrix
2. Momentary consumption (L/100Km) - based on the current "ti"signal and
road speed
3. Momentary consumption (L/h) - based on current "ti"signal only
4. Range consumption -5.
Momentary range (Km) - range left on fuel in tank when reserve light is on
6. Not used
7. Fuel level from the instrument cluster - average value
8. Momentary speed (Km) - current speed averaged over 2 seconds
9. Operating voltage - available to BC from KL R
10. Language for display -11.
Units readout - for display of mileage/gallons - etc.
12. Average speed for arrival time function
13. Momentary arrival computed
14. ROM - date
15. Readout of fault memory - vendor use only
16. I/O port status - vendor use only
17. Encoding of vehicle specific data - vendor use only
18. Alarm mode - for BC code function - pulse or continuous tone
19. Lock/Unlock function
20. Fuel consumption correction factor
21. Software reset function
The test functions are accessed by pressing the "1000" and "10" buttons
simultaneously.
Test functions #1, #10, #14, #19 and #21 are unlocked and can be called up
by entering
the number and pressing SET/RES.
The other test functions are locked out and test #19 must be used to release
the test func-tions
for display. The unlock procedure is as follows
• Call up test #19 - " LOCK ON" is displayed in the matrix display.
• Use the number input buttons to enter the sum of the day and month
displayed on the
clock.
• Press SET/RES and the computer is now unlocked for display of all test
functions
To relock the test functions when through with the testing, call up test #19
and press
SET/RES twice.
E39 OBC

[hole]

thanks a lot of Monday I verify the everything and I adjourn you.............

[hole]

x smirnoff_rules :thanks to your suggestion everything of him e' resolved in well and I am very happy great

[smirnoff_rules]

glad to be of help