[aftermath]

How to Multiboot from an AB IPBox HD using a USB stick.



Format USB STICK to FAT32 , then unpack the file below and rename it usb_upgrade.img and transfer it to the usb stick.

Remove the USB Stick from the PC then drop down the front panel on your AB IPBox HD and press the round Standby button and the ok
button together and let them go to put the box into standby.

Insert the USB Stick into the USB Port at the back of your IPbox HD

Hold in the Standby button on the front panel and then when the box states BOOTING in the front display press the UP button and
then release both buttons, USB UPGRADE should be displayed in the LED display.

If this giets you Err 10 or stops on booting, open PCeditor ( latest ), and flash it using the normal methos for flashing an image.

In the box LED you should see it go to Erasing, then go to Flashing, this will only take a few seconds.After that it will say done.

Time to re boot your box holding the relevent remote control key number to boot from your desired device.

1) boot from cdkroot
2) boot from USB with hdd
3) original images
4) boot from release
5) boot from USB without hdd
6) boot from SATA hdd
7) boot from flash

[gaz t]

hi all when multibooting which number should i be pressing on reboot, i presently have a nlb image and i've tried to boot to e2 image on usb drive but each time it boots to nlb image , i followed the tut to install multiboot successfully and i have been pressing 2 on remote (i have a hdd fitted) so i think i've done something wrong unless i'm pressing wrong number on remote.
thanks

[despdan]

Press & Hold down 2 for 5sec

did you flash the multiboot upgrade?

[gaz t]

g'morning dan,yes i followed the tutorial on how to multiboot from this site i got err 10 on first try so carried on with what it says in the tut and flashed it with pceditor , flash finished with "done" so i'm assuming it flashed correctly.

[gaz t]

hi all, just to let you know all sorted now i don't know what the problem was but with a little persistance i managed to boot to e2. thanks

[jozix]

how to do a multiboot? I still don't get it... is just an NLB image on the flash enough to to the multiboot? (I want to have let's say ENIGMA2 SIFTEAM on USB and NLB team image on FLASH) and to be able to boot one of them when I power on ipbox. Is it possible? What is the howto? thank you

[Phillhenry]

how to multiboot ? do you know where to find manual ?

[aftermath]

Originally Posted by Phillhenry how to multiboot ? do you know where to find manual ?

read post 1

[remikg]

ill test it

[wilhelkl]

Hello all,

I have the same problem. I have installed the multiboot config file and I have an E2 image (unpacked tar file) on an USB stick. Pressed 2 during booting but the box does just display booting and nothing hapened. Is there a more detailed description for installing a multiboot environment with DGS image and ES available?

[ziejas]

Originally Posted by wilhelkl Hello all, I have the same problem. I have installed the multiboot config file and I have an E2 image (unpacked tar file) on an USB stick. Pressed 2 during booting but the box does just display booting and nothing hapened. Is there a more detailed description for installing a multiboot environment with DGS image and ES available?

I have the same - only "BOOTING"

[carrpet]

Hi Guys, once I install the usb multiboot config I cannot get the box to boot from my flash image when I press and hod down 7 on the RMC. All I get is "booting". I would welcome some help
and suggestions please

[mistic]

hi friends, my cube250hd has de same problem, only display booting.
I can´t boot flash image and can´t boot usb image.

[carrpet]

Hi Guys, I can now get the box to boot my original image in flash which is Option 3 not Option 7.

I have used Paragon Hard Disk manager to format my USB stick in Linux ext3 which I understand is the preferred disk format. I still can't get my E2 iamage in USB to boot though

[aftermath]

Originally Posted by carrpet Hi Guys, I can now get the box to boot my original image in flash which is Option 3 not Option 7. I have used Paragon Hard Disk manager to format my USB stick in Linux ext3 which I understand is the preferred disk format. I still can't get my E2 iamage in USB to boot though

boot box in flash image and FTP to mnt/usb/usb0

see if all the files have unpacked in there.

if you see all the folders , switch the box off and when switching it backk on hold in the "2" key on Remote control for 5 seconds, if it dont work first time try a few times ..

Also a 2gb USB us best to use as more memory than that some USB sticks wont get recognised.