vu duo - stuck on starting - putty log - have a look please

[kaisar1]

BCM73350010
012
Shmoo Version=1.9

MEMC-00000000 RW=00000009 WW=00000023 G=00000001 R=00000004 W=00000007
MEMC-00000001 RW=0000000F WW=0000004B G=00000001 R=00000009 W=00000005 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Thu Sep 29 12:01:32 2011 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd
!!!!! UNC read error occurred, while reading from NAND flash

DDR Freq: 395MHz
CPU speed: 405MHz
Memory Config: 32+16 non-UMA
Device Tech: 1Gb
Total memory: 384MB
Boot Device: NAND
ECC: Hamming
Total flash: 128MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.

checking usb
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3
Loading: !!!!! UNC read error occurred, while reading from NAND flash
Failed.
Could not load : I/O error
CFE>


--------------------------
connection via serial cable, ethernet cable going from router to pc and another to vu duo


thanks

[kaisar1]

anyone understand the log, what does unc error mean? and is it repairable?

[DOUGALMCD]

I read something similar to your problem and they had box to pc serial and using hyperterminal while reflashing usb they came up with a bit more info. Basically it was bootloader error. Maybe someone will come up with something for you now. hth Translated what i could.

Before flashing you should do these steps:
1. connect the serial cable between box and PC
2. colleagues will co hyperterminal / minicom to the serial
3. stick the pendrive in the box
4. turn .... and see what appears to you .....
5. output post it here .... this after flshato by vu + utilquesto during flash usbquesto avvioStrano the following behavior.
Have you tried to flash a BH prior to 1.6.6 or image Vu + Only official? Before you ... I have to try the original one .... I had already thought ... I try and let you know ... graziequesto after image vennesimo original image with the original attempt utilu vu + util + ... but I doubt you avvii.sicuramnete has nothing to do ... but when I put the 166 ... the duo is dead ... and just went nuts. will be a case ..??
To prove the duo from upgrading the bootloader and usb ... part of fpgfleshato from lan ... no! ... Why? Ada LAN? I do not like the system to tell the truth .... would be best to pure serial ... but I have never used Vu + Util and I have no idea if it can be used only for the serial connection in fact (it will take a lot of time ... but you could avoid trouble). Hessi you'll see that the duo did not make 'I ....
for now ... eh eh eh, LE arrivo.o taken into Chestnut GOD NOW YOU WOODPECKER!
The LE also iooooooooooo I would rather ... I want too Cos' has more 'the LE (limited edition) as well as being a different color? E' brushed aluminum (I think) ... In short it's cool I'll take a good 'last ...
u no FPGA

[digicon]

writing vfd
!!!!! UNC read error occurred, while reading from NAND flash

That part is as mentioned by DOUGALMCD is a Bootloader Error, If your trying to flash the VU original firmware 0.7.nfi file you may be wise to try and force flash again the 3.1.1 kernel before trying to flash the VU firmware

[kaisar1]

I read something similar to your problem and they had box to pc serial and using hyperterminal while reflashing usb they came up with a bit more info. Basically it was bootloader error. Maybe someone will come up with something for you now. hth Translated what i could.

Before flashing you should do these steps:
1. connect the serial cable between box and PC
2. colleagues will co hyperterminal / minicom to the serial
3. stick the pendrive in the box
4. turn .... and see what appears to you .....
5. output post it here .... this after flshato by vu + utilquesto during flash usbquesto avvioStrano the following behavior.
Have you tried to flash a BH prior to 1.6.6 or image Vu + Only official? Before you ... I have to try the original one .... I had already thought ... I try and let you know ... graziequesto after image vennesimo original image with the original attempt utilu vu + util + ... but I doubt you avvii.sicuramnete has nothing to do ... but when I put the 166 ... the duo is dead ... and just went nuts. will be a case ..??
To prove the duo from upgrading the bootloader and usb ... part of fpgfleshato from lan ... no! ... Why? Ada LAN? I do not like the system to tell the truth .... would be best to pure serial ... but I have never used Vu + Util and I have no idea if it can be used only for the serial connection in fact (it will take a lot of time ... but you could avoid trouble). Hessi you'll see that the duo did not make 'I ....
for now ... eh eh eh, LE arrivo.o taken into Chestnut GOD NOW YOU WOODPECKER!
The LE also iooooooooooo I would rather ... I want too Cos' has more 'the LE (limited edition) as well as being a different color? E' brushed aluminum (I think) ... In short it's cool I'll take a good 'last ...
u no FPGA

mate what language is half that post in

co hyperterminal / minicom where can i download the software from?

[cactikid]

meaty language whay else

[DOUGALMCD]

Talking Italian.