good question!
who killed President Roosevelt?
good question!
who killed President Roosevelt?
faster and easiest way for decode:
cut immo line (pin 37 1.4 and 1.6, pin 35 1.8 and 2.0L)
find flash
connect ecu to car and switch ing on
short circuit to ground for few to ten times pin 22 for flash 28F512/29F010
short circuit to ground for few to ten times pin 23 for flash 27C512
start the car
Last edited by atomiczen; 17th March, 2014 at 02:42 PM.
ProTuner since 1999
a35l35 (13th January, 2020), gelomeloman (29th November, 2017), pawelelectro (2nd April, 2015)
Hi Members:
I tried the method #1, light stop blinking and now is always ON, I tested the ecu on bench, the 2 pins for injection control are working (pin 4 pin 30) fuel pump relay is workin too, but I don?t have coils activation signal on pins 28 and 29.
Do any of you had this problem ??
Maybe bad TMS erasure or bad coils stage output ??
thanks
Tried this method many times with renault engine , worked 100%
Now have in Hand Hyundai Siemens H103955556A , not working with these two method , tried with ecu deconding tool , selected standard mode , not working.
Can somebody clarify immo system and wiring for hyunda elanta coup? , 1.6V.
Hi, this is for 28F512 rigth? you have work with 27C010 on fenix 5?
Thanks to the solution ,,,works,,,,,, tested on two cars
Do we separate 1-9 for flash28f512 or what Blcaml Please illustration
Last edited by abu deab; 9th May, 2015 at 04:15 PM.
hi to all,
I always take a backup of Flash before I make it immo off, How can I make a backup of fenix5 without desoldering Flash ??
Hi there Guys.....
I have a problem. This is the second time I have a Megane Scnenic with the FENIX 5 ecu. When I connect the ECU as per diagram the MIL Light Doesn't Flash nor come on. I Checked all wires but nothing.
Does it require high power or what? I am using a 12V 7AH Alarm Battery and these small Jumper leads with Crocodile Clamps on the ends.
Any Other suggestions???
Last edited by obeids; 14th December, 2015 at 01:26 PM.
i cant downloading it
megane solution very simple2.rar and soultion2fenix5.rar are not open.
please send again for me
thanks
I CAN NOT REACH THE FILE
buy a renault decoder for
SIEMENS FENIX3B BOSCH MSA15.5 (DTI)
SIEMENS FENIX5 BOSCH EDC15C3 (DCI)
SIEMENS SIRIUS32 LUCAS DCU3R (1.9D)
SAGEM SAFIR (55pin) Coded fuel cut-off valve (1.9D DDS)
SAGEM SAFIR2 (35pin)
BOSCH MOTRONIC MP7.0
MAGNETI MARELLI IAW 06R
MAGNETI MARELLI IAW 8R.30
rumentil58 (10th May, 2018)
Thanks for this method
Im sorry for waking this old topic but im hoping that someone can help me...
Problem is:
Renault Megane Coupe 1998 2.0 16v 103kw
Replaced uch(ucp) from inside the car, in top of pedals but car wont stard because immo flashing red on dash. After that some mechanic comes with diagnostic and turn the immo off and flashing light gone but car again wont start just cranking. After this solution i see that "zig zag" flashes all the time and now we cant connect diganostic to read ecu and even ucp(uch)...
Can anyone point me in right direction do I maybe need to do solutions from start of topic after turning immo off on diagnostic?
And I need to to this can someone post solutions how to do it because i cant download attached files from start of this topic...
Thanks in advice
Attachment 942800
Last edited by centrozax1; 14th February, 2023 at 02:48 PM.
Bookmarks