Ford Escape 2009 odometer - Page 2
Register
Page 2 of 3 FirstFirst 123 LastLast
Results 16 to 30 of 36
  1. #16
    DK Veteran
    afitijuana's Avatar
    Join Date
    May 2010
    Posts
    877
    Thanks Thanks Given 
    2
    Thanks Thanks Received 
    157
    Thanked in
    114 Posts

    Default

    Just use a multi-meter and find the ground check for continuty from any capacitor labeled wit a black strip.

    The next point next to Ground is Reset after Reset is VVD and on the oposite side of ground is Data

    Ilustrations show as follow.


    * simulate BDM pads.
    N/A mean not used or not avilable.

    typical show as 2 row of 3 points could be horizontal or vertical.

    * *
    * *
    * *

    * * *
    * * *



    ---------------CONFIGUTARATION 1 ---------------------------

    * DATA * N/A * N/A

    * GND * RESET * VvD

    ------------------CONFIGUTARATION 2 ---------------------------

    * GROUND * RESET * VvD

    * Data * N/A * N/A


    ----------------CONFIGUTARATION 3 ---------------------------


    *VvD * RESET * GND

    * N/A * N/A * Data



    ----------------CONFIGUTARATION 4 ---------------------------

    * N/A * N/A * DATA

    * VvD * RESET * GND


    UPA will do any 912 as long as they aren't secure, no need of rs260 or 270 or else, as far as X-progm as log it support motorola MCU 68hc9s12 you are ok.
    Last edited by afitijuana; 23rd August, 2013 at 06:23 PM.

  2. The Following User Says Thank You to afitijuana For This Useful Post:

    claudio35 (23rd August, 2013)

  3. #17
    Moderator
    PremierD's Avatar
    Join Date
    Jun 2009
    Posts
    12,455
    Thanks Thanks Given 
    2,630
    Thanks Thanks Received 
    9,122
    Thanked in
    4,299 Posts

    Default

    All that is in the two pictures mate ..

  4. #18
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    so that would be

    ----------------CONFIGUTARATION 4 ---------------------------

    * N/A * N/A * DATA

    * VvD * RESET * GND

  5. #19
    Moderator
    PremierD's Avatar
    Join Date
    Jun 2009
    Posts
    12,455
    Thanks Thanks Given 
    2,630
    Thanks Thanks Received 
    9,122
    Thanked in
    4,299 Posts

    Default

    ..........................

  6. #20
    Moderator
    PremierD's Avatar
    Join Date
    Jun 2009
    Posts
    12,455
    Thanks Thanks Given 
    2,630
    Thanks Thanks Received 
    9,122
    Thanked in
    4,299 Posts

    Default

    Its the position of the wires relative to each other .. VSS opposite BGDB.. RESET next to VSS and VDD next to it ... its always the same ..
    Last edited by PremierD; 24th August, 2013 at 08:49 PM.

  7. #21
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    Ford Escape 2009.jpg



    DIGIPROG III should do this right ? with cable st-48.
    Last edited by norbisko; 23rd August, 2013 at 11:24 PM.

  8. #22
    Moderator
    PremierD's Avatar
    Join Date
    Jun 2009
    Posts
    12,455
    Thanks Thanks Given 
    2,630
    Thanks Thanks Received 
    9,122
    Thanked in
    4,299 Posts

    Default

    Hate to burst your bubble mate .. but the diggy wiggy can't read 9S12 mcus .. without an adaptor .. (which does not work very well anyway) .. Use UPA .. or Xprog . and post the dump ... OR do the job ObD ..

  9. #23
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    Quote Originally Posted by PremierD View Post
    Hate to burst your bubble mate .. but the diggy wiggy can't read 9S12 mcus .. without an adaptor .. (which does not work very well anyway) .. Use UPA .. or Xprog . and post the dump ... OR do the job ObD ..
    I managed to do 08/2005 E-250 with it...which has 9S12

    http://www.digital-kaos.co.uk/forums...67/index2.html

  10. #24
    Top Poster
    Join Date
    May 2012
    Location
    Uk
    Posts
    125
    Thanks Thanks Given 
    19
    Thanks Thanks Received 
    11
    Thanked in
    10 Posts

    Default

    Only secured micros BMW Mercedes with wigi need adapter. Ford/Nissan etc ok with st48

  11. #25
    DK Veteran
    XmoDDeR's Avatar
    Join Date
    Mar 2011
    Location
    putting salt on leeches, one grain at a time!
    Posts
    1,837
    Thanks Thanks Given 
    600
    Thanks Thanks Received 
    1,152
    Thanked in
    612 Posts

    Default

    yes it wiil do escape no problem st48

    Reading is fundamental, asking is easy............................

  12. #26
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    ok here is what I got, I soldered the st-48 to bdm, went under ford Escape menu, read 0 miles. didn't want to change anything, so went under eeprom menu mcu motorola 9s12, read ok, I could see the data. the I used tachosoft for edit

    Car type: Ford Escape - 9s12ZH256

    The mileage is stored in the next lines:
    0720: xx xx xx xx xx xx xx xx xx xx xx xx 1E 5C xx xx
    0730: 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx
    0740: 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx
    0750: 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx
    0760: 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx
    0770: 1E 5C xx xx 1E 5C xx xx 1E 5C xx xx xx xx xx xx
    where the next bytes:
    1E 5C - is a mileage

    My original values were 1D63 ( cars mileage 60,xxx mi ).
    I changed the values to 1263 (38,xxx mi )

    And hit write, everything was written ok. Now When I put cluster in, it shows "ERROR mi" in mileage window . car doesn't start. Is there another location for mileage that needs to be changed also ?

  13. #27
    Moderator
    PremierD's Avatar
    Join Date
    Jun 2009
    Posts
    12,455
    Thanks Thanks Given 
    2,630
    Thanks Thanks Received 
    9,122
    Thanked in
    4,299 Posts

    Default

    No mate .. sorry .. Have you tried putting back in the original file?

  14. #28
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    I wanted to try editing the 4 values first ( 1D63 original to 129A new) instead of just the 2 first . maybe there is some kind of corruption in that...

  15. #29
    DK Veteran
    norbisko's Avatar
    Join Date
    Nov 2009
    Location
    In a House
    Posts
    317
    Thanks Thanks Given 
    196
    Thanks Thanks Received 
    25
    Thanked in
    20 Posts

    Default

    After changing the values to 129A, everything went back to normal.
    Last edited by norbisko; 24th August, 2013 at 09:26 PM.

  16. #30
    DK Veteran
    XmoDDeR's Avatar
    Join Date
    Mar 2011
    Location
    putting salt on leeches, one grain at a time!
    Posts
    1,837
    Thanks Thanks Given 
    600
    Thanks Thanks Received 
    1,152
    Thanked in
    612 Posts

    Default

    Send me the bin

    Reading is fundamental, asking is easy............................

 

 
Page 2 of 3 FirstFirst 123 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.