I just started to download WIS-EPC-EWANET_05.2010_DVD. That is ok? Those are so big files that I'm running out of space.. Need now get back up cause get das/xentry work and If I restore back up to other HDD will it work at other laptop? Or need I change something or made new install? Install takes so much time. Have now used many days of my summer holiday for that and not yet Wis/epc installed
On diagnosis I have 9551 error
On Caesar:
SystemCheck :
Check serial ... 0 Ok
CAESAR HW Detection :
D2Access ... 0 Ok
D2DownLoad ... 104 - No Download possible
I use the notive com port of my laptop.
Sistem work perfectly with other mux.
I notice, that the 104- No Download possible error comes also on a good mux if is not powered on Caesar test.
Thanks!
Hi again
I have run a few tests again with 2 Mux- (one was a replacement) Here are the results :
a) I managed to get a few clean - all pass caesar tests
b) Most of the tests gave me the 104 error
c) IN ALL CASES I WAS ABLE TO DIAGNOSE / CODE my w211/facelift/MY2007 (loaded with extras)
So it remains a mystery why this 104 error comes on - Maybe somebody else whow has come across such a case can shed some light !!
Also have you installed the fixes by Zolookas ? (copy the three files cal.ini, c32s.dll, lic.sli)
Did you ever run DAS with the Mux connected before copying above files ?
Did you change in cal.ini PLATFORM=PART_D2 ?
Also try another key for DAS.
and we will always be here to try to help !!!
hi, I am also having this same error with new compoact 3 kit I bought from china. kit comes with pre-installed das xentry 03/10 on HDD, I have tiried hdd and mux on both ibm t23 and t30, with same error. 501.9551 when trying to connect to car.
From reading on this extremely helpful forum, I don't think its a mux problem, as caesar test just says 'device isnt in state available' as with previous posts on this thread.
I have tried editing cal.ini for device = part_d2->d
com port is set to com2 at 115200 etc., but still same problem.
i had downloaded zolookas fixes but hav not applied them as yet. I have attached zolookas fixes for anyone who needs it.
I was wondering if I should try another key first(how do i get another key?) or should i apply zolookas fixes first then if that doesnt work try a different key?
Please help.
In order to get a key for DAS post you LanId.
Also if things do not go favourably I would greatly recommend to download DAS2010.01 and make a fresh installation using Zolookas guide letter by letter.
Mr Zolookas has spent a lot time and effort in order to make installation really easy . And he was nice enough to share with all of DK
So take advantage of his work !!
Last edited by gmatj; 22nd August, 2010 at 10:20 AM.
Try also reconnect Car - Mux cable. Sometimes it worked to me.
After it gives error make reconnection. Mine worket also by 19200 bit/s speed.
note: DAS will work with USB->serial cards (using Prolific drivers).
I have tested in two laptop ( asus eepc and ibm t30 ) In the t30 using the internal comport i have this 1.501.9551 error but using the usb>serial everything works ok.
Cheers,
red
cal error 9551 is for hardware so check your cables or com port only
Hi,
sorry, been busy with stuff why hadn't checked the thread.
Ok, I tried zolookas fixes, and tried developer key, but still same error. Also did some other bits but didn't change a thing in caesar test.
I am convinced its a cable or comport problem, but since it was the same in my T23 which had a verified com port, I am leaning towards a faulty cable , namely the rs232 to rs485 converter cable.
I contacted the seller (china) and they also said it is most likely this cable. They will send me a replacement cable free, this should arrive sometime after the bank holiday.
i will let you guys know if this solves it!
cheers.
I'm back and happy to report that it was indeed the cable (rs232 to rs485) which was faulty.
Now my das is working fine !!!!
Thanks to everyone for their help, really appreciated.
Now , I would like to use xentry, but before I do so, do I need any special keys , or only if i want to run xentry dev mode.
Also, do I need to apply the timeout fix or should i run it and see first?
Thanks guys.
das fault 1.1 how to fixed it.
thank you
Bookmarks