Hi, i have an isb ecm, that seems all be ok , i mean no components blowed . But problem is positive to ground , and impossible energized .
Can someone gimme advise ?
Hi, i have an isb ecm, that seems all be ok , i mean no components blowed . But problem is positive to ground , and impossible energized .
Can someone gimme advise ?
the life is easy... people complicate!!!!!!!!
life is funny just step away of people that wants make your life a shixx
......
http://youtu.be/PEw3nYmpEys
Hey donnie , yes isbe. Cummins. Not solved, i had to replace the ecm, and try to find the problem in the old one.
the life is easy... people complicate!!!!!!!!
life is funny just step away of people that wants make your life a shixx
......
http://youtu.be/PEw3nYmpEys
Hi Camp.
Sorry for a late response. Hope I understand your post clearly but i once had an isbe ecm that failed and shorted between positive and negative and i resolved the issue by replacing the large surge protection diode inside the ecm. if that is your problem then just removing the diode will cause your ecm to work again but you will need to replace it for future protection of the ecm. hope this helps.
regards
Donniemnemonic
Poptest (18th December, 2015)
Thank you donnie
the life is easy... people complicate!!!!!!!!
life is funny just step away of people that wants make your life a shixx
......
http://youtu.be/PEw3nYmpEys
I have a 3619037 Celect ECM with fault 342. Engine does not start and it also does not communicate with Insite.
Please advise me if there is a way to fix this.
Thank you.
celect plus ecm not reving up any solutions .
Did you try to put the key switch on and accelerate full throttle three times before starting the engine?
If so there could be an internal power supply failure, which could be lost of the 5volts to the accelerator pedal or there is no ground within the ECM to that circuit.
hope this helps...
All you need to do is to put it in )ROM BOOT MODE)
Have your calibration cd and your insite ready for calibration and have an OEM harness connector with you (preferably a short harness connector with loose ends/wires)
Put together these wires from your OEM harness pins 10+12 and 14 together then turn key on while holding these wires together in order for the ECM to swith into ROM Boot mode...
after this process connect to Insite and calibrate the unit using that same part number. CAUTION: MAKE SURE YOU USE THE SAME PART NUMBER WHEN CALIBRATING EVEN IF IT FAILS TO CALIBRATE AND WHEN RESTARTING THE CALIBRATION...
ITS WISE TO DO THIS PROCESS ON THE BENCH....
Don't forget to thank.
Wayne Techiemec (13th May, 2021)
Those are for the injectors. usually they are blown by the faulty mosfets. they supply current to the mosfets and there is an overload to the resistors.
Hi bud I have the same problem please let me kW if u find the problem but I have a feeling it's a soft ware problem cause if u leave the unite on for about five mins u can put the restore in while the unite is on n u will c it don't blow let's chat on email shaunchetty2510@gmail.com
Hola amigos
cualquier immo fuera, FORD F100 XLT 3.9 DIESEL
ECU es CUMMINS MOTOR COMPANY
P / N 4898112
S / N 84165667
E / C T90179.01
SC 98463
ESN 36187110
MEMORIA 95640
como hago para subir lectura de la memoria?
Cummins N14 Celect ECM diagrama interno.pdf
if you serve .. internal ECM nesecito diagram isx cm570 ... I have a problem with a module with code 124 always active (temperature Admission) and 213 (oil temperature) Could someone Past work (not for harness circuit problem. It is 100% internal circuit module someone could help me?
elbarto (24th May, 2017)
"with code 124 always active (temperature Admission)" >> right 124 fault code guys?
Bookmarks