CUMMINS ECM REPAIR TIPS

[mmfix]

Hello, which Programmer you guys using for Xicor x28c64-jm-20
I have N14 Cellect Plus with faulty code 111. We reprogram the ECM with a Insite 8.7 and faulty code gone for a 10 days and today is back.
I was reading that need to change the Xicor x28c64-jm-20 but after changing the ECM wont program with Insite and i believe that the IC must program before solder.
PLS any help will be appreciate
Thank you !

[mmfix]

Hi I need your help
Ecu 2350B
Insite error code 5080
ID from Calterm:
Device Address 0x00
Product ID: ABC,BDC
Part Number:5317110
Serial Number:5203034
ECM ID:G2
I only have an ECU with only one sticker on it , is it possible to somehow find out what is to be uploaded there ??? maybe someone has such a file for calterm???
I can only upload it on the bench or JTAG(Trasdata)
Attachment 892008Attachment 892009Attachment 892010

What you can do for cummins you just need a part number and Engine Serial number and you can see which Software calibration you need to install.
Please provide a Engine SN.
I have seen ECM that are calibrate with a wrong Software because people some time buy and install without programming.

[juzzix]

Hi to everyone.
Celect plus emc and fault code 441, Low battery level. Bat voltage measurement singnal goes correctly thru the multiplexer circuit.
What could cause this fault inside ecm?

[donniemnemonic]

This thread needs reviving. After years of working on these knowledge sharing is not a bad thing. Will not spoon feed anyone but will nudge you in the right direction. Best way to learn is by experimentation.

Regards
Donniemnemonic...

[mmfix]

Hello, i have N14 celect that has a BAD EEPROMS is there some one that can upload the HEX or BIN from a EEPROMS 2864?
I try to calibrate with new ICs but stop on 65% and if somebody can give me an Idea i will appreciate!
Thank you !

[mmfix]

Im agree with you donniemnemonic!
After so many years we need to refresh the topic and i hope there will be more people agree with you.
Im going to be here and help with my experience as a electronic technician.

Who is agree to refresh the theme and start helping each others ?

[linux2010]

Available
CAT ADEM III internal circuit diagram
CAT ADEM 4 70/120 pin internal circuit diagram

CAT ADEM 4 64/64 pin (C6.6 C6.4) internal circuit diagram

[mmfix]

Available
CAT ADEM III internal circuit diagram
CAT ADEM 4 70/120 pin internal circuit diagram

CAT ADEM 4 64/64 pin (C6.6 C6.4) internal circuit diagram

What is the price ?

[linux2010]

What is the price ?

CAT ADEM III internal circuit diagram--- 100 USD

CAT ADEM 4 70/120 pin internal circuit diagram ----- 250 USD

CAT ADEM 4 64/64 pin (C6.6 C6.4) internal circuit diagram----- 250 USD

[mmfix]

Question Guys i have a bad Cummins Cellect pand ECM and water goes inside i clean fixed but the timing chip SC408069FMFN is bad and ECM wont connect to PC I replace it from another board but still not connect to the PC but now consume normal Amps.
My question is is the SC408069FMFN need to be program or not?

Thanks !

[donniemnemonic]

Hello, i have N14 celect that has a BAD EEPROMS is there some one that can upload the HEX or BIN from a EEPROMS 2864?
I try to calibrate with new ICs but stop on 65% and if somebody can give me an Idea i will appreciate!
Thank you !


HI m8

Did you ever get this resolved. Was offline but just seeing your message now.

[donniemnemonic]

Hello, i have N14 celect that has a BAD EEPROMS is there some one that can upload the HEX or BIN from a EEPROMS 2864?
I try to calibrate with new ICs but stop on 65% and if somebody can give me an Idea i will appreciate!
Thank you !

HI m8

Did you ever get this resolved. Was offline but just seeing your message now.

[donniemnemonic]

Question Guys i have a bad Cummins Cellect pand ECM and water goes inside i clean fixed but the timing chip SC408069FMFN is bad and ECM wont connect to PC I replace it from another board but still not connect to the PC but now consume normal Amps.
My question is is the SC408069FMFN need to be program or not?

Thanks !

Hi m8
Did you ever get this resolved?

[mmfix]

Hello donniemnemonic, sorry for the late answer but i see the thread is almost dead and no one repair or share any more information. I didnt expect to answer me.
Also im not sure how to make the forum notification on treads the someone answer me.
Yes i did fix that ECM I contact with some of the members on direct message unfortunately no one had exact what im looking but i got a luck and i got the same part number ECM for repair and i was able to take the Bin flash files from it and fix the my other unit . I would say will be very good if we make a closed good community for ECM repair. I do repair phone and the community is very very powerful out there even FB pages and Wiki. If you want to contact faster with me just use PM-personal message