Tips and Tricks using Das Developer edition

[Mackhack]

Not possible bc ECU is a theft relevant part. Only a official dealership can help you if you bring proof of ownership of the vehicle! They then will contact MB in Stuttgart, Germany!!!

[anttilai]

HI. I click on Crashspeicher l?schen them F3 after I click on F3 is tell me RESULT: security access denied - security access request. How can I unlock it please help me.

I have this same problems and I can't even unlock ecu because it tells me same "security access denied". I use das 2013.5 developer mode, can it be too new version etc.

[anttilai]

Any ideas why I can't unlock ecu? Do I need das 2009 instead 2013 ? Now even in simulation unlock actuations give me result=0, is it OK or should it be result=1?

[Mackhack]

Zero means error, 1 means OK

[anttilai]

I have tried actuations (simDAS) @ "development\complete index of actuations" and always it told me result=0. I have tried w210, w211 and EGS/AB/... Do I need some fix or what is problem? I have installed AddOns 2777,2779,2781,2782, do I need more or do I have all of addons? I'm confused about this situation..

[Fec001]

Here is how to : clean ASSYST Plus Memory
All we need is DAS in Developer mode
In Developer mode : (tested version 07-2009)
Steuergerate (Control units) ->F3
Aufbau (Body) ->F3
ZGW (CGW) ->F3
Entwicklungen (Development data) ->F3
Steuergerate - Anpassungen (Control unit adaption) ->F3
Programmieren (Update) von Steuergeraten (Control module programming) ->F3
Steuergerat programmieren (Auswahl) (Program control unit (Selection)) ->F3

Now we have 2 options to flash the ZGW/CGW with, choose the correct one
Don't panic ! if you choose the wrong file , it terminates process and you can do it over again
Confirm Flash pop-up with Ja (Yes)
After that it says : "Das Steuergerate wurde erfolgreich programmiert"
-> "OK" it ask for a reset -> JA (Yes) ->
ECU Reset (FN_ECU_Reset) ->F3 again ->F3

Now you Completed full History wipe out
Everything discussed in this post is for experimental and educational purposes only

In W164 possible too?
In zgw developement data there is only coding and 1 other is avaible. No control unit programming.
But I need clean ZGW history because somebody plays with it and now the whole service is a mess. Can't reset service etc....

[Plutoe]

You may want to read your quote one more time----what version of DAS was used and what version are you trying to use to accomplish the task!!!

[Fec001]

tried 2013 and 2010. in version 2010 a tried w211 with simulation and there is option "update" in develpement data

[bersch8688]

I have Mercedes W216 ---> 2007
I have change the KM/h from 260Km/h to 320 Km/h AMG.

The Dashboard dont change Screen to AMG.

WHY????


PLEASE HELP

[snelle rabbit]

(Ecu hardware reset)

Did you make the reset, with DAS?

[bersch8688]

(Ecu hardware reset)

Did you make the reset, with DAS?

YES, is the same

[Mackhack]

I have Mercedes W216 ---> 2007
I have change the KM/h from 260Km/h to 320 Km/h AMG.

The Dashboard dont change Screen to AMG.

WHY????


PLEASE HELP

Why should th CI "change" to AMG????

[Fec001]

I have Mercedes W216 ---> 2007
I have change the KM/h from 260Km/h to 320 Km/h AMG.

The Dashboard dont change Screen to AMG.

WHY????


PLEASE HELP

You need AMG FW eprom dump for KI. Coding not enough!

[Mackhack]

When or why would the KI show AMG?

[Kaluluka]

When or why would the KI show AMG?

KI needs AMG file in the EEPROM to show AMG. Otherwise no go................