Tips and Tricks using Das Developer edition

[Qrius]

This started as a sugestion

In here i will post my allready published developer tricks that are circulating around Dk

From time to time i will add some new tricks as well

Hope this will encourage others as well

[Qrius]

Here is how to do it,

In Developer mode :
Kombiinstrument -> Diagnose nach Werkangabe -> Steuergerate-Anpassungen ->
Steuergerate-Anpassungen (Variantencoderierung) -> Variantkodierung Werkeinstellungen ->

In the menu that shows , you scroll down untill you read the line : Tankinfo im Reichweitebild
enable this option
now you have tankinfo in the screen that otherwise only showed range

If you allso wanna adjust the way fuel consumtion is showed
you scroll a little more down untill you read the line : Verbrauchanzeige km
you can change it from L/100km into km/l

Scroll down and confirm Coding by pressingF3

if you watch your Instrument Cluster , you notice that scrolling through the menu , nothing changed .

For this , the "Kombiinstrument" needs a reboot.
to do this in Developer mode we go back by hitting F1 -> 3 times
then choose Ansteuerungen -> Gesamstliste aller Ansteuerungen ->
Scroll down untill you see the line : Steuergeraet Resetten (PowerON-Modus) (FN_Reset_SG_Power_ON)
Press F3 and confirm again with F3
Now you will see the "Kombiinstrument" reboots

If you think this would help you
Please dot not forget to click THANKS

[Qrius]

Here is how to : clean ASSYST Plus Memory
All we need is DAS in Developer mode
In Developer mode : (tested version 07-2009)
Steuergerate (Control units) ->F3
Aufbau (Body) ->F3
ZGW (CGW) ->F3
Entwicklungen (Development data) ->F3
Steuergerate - Anpassungen (Control unit adaption) ->F3
Programmieren (Update) von Steuergeraten (Control module programming) ->F3
Steuergerat programmieren (Auswahl) (Program control unit (Selection)) ->F3

Now we have 2 options to flash the ZGW/CGW with, choose the correct one
Don't panic ! if you choose the wrong file , it terminates process and you can do it over again
Confirm Flash pop-up with Ja (Yes)
After that it says : "Das Steuergerate wurde erfolgreich programmiert"
-> "OK" it ask for a reset -> JA (Yes) ->
ECU Reset (FN_ECU_Reset) ->F3 again ->F3

Now you Completed full History wipe out
Everything discussed in this post is for experimental and educational purposes only

[Qrius]

Make sure engine is running !!!

In Developer mode you need to go to Entwickelingsdaten - > ansteueringen -> Gesamstliste aller Ansteuerungen

to see how many times brake has been pressed there is a line that says: Bremsenzahler (DJ_GetBrLive)

then 1 line down there you see Bremsenzahler aktualisieren und Lebensdauerzahler F neu berechenen -> click it !
Parameter uINBR = 0
then click F3

1 line down Bremsenzahler auf beliebigen Wert setzen (DJ_SetNBr) -> click it
Parameter uINBR = 0
then click F3


then scroll down untill you see the line's :

Lebensdauerzahler F neu berechenen (DJ_CalcLiveTime)
Parameter uINBR = 0
then click F3

Lebensdauerzahler F neu berechenen und schreiben (DJ_BuildAndWriteF)
Parameter uINBR = 0
then click F3

Log out of SBC !!
log out of verhicle !!

let engine run at least 10 minutes or drive at least 10 minutes

If no coils are damaged , SBC fault code is not AKTUEL nomore

[Qrius]

In Developer mode :
Audio, Video, Navigation und Telematik ->F3
a screen might pop up with all kind of settings, ignore and press F2
New screen with ESD warning ->F3 COMAND /AUDIO -AUDIO 50 oder COMAND ->F3
Entwicklungsdaten ->F3
Steuergerate-Anpassungen ->F3 Steuergerate-Anpassungen (Variantencoderierung) ->F3
HU Parameter ->F3 scroll down to line: Driving speed is more than 0 kph and
Driving speed is more than 10 kph and BOTH enable them and ->F3 to confirm coding
Now you be able to watch DVD/TV when car is in motion

This procedure won't work for W204 W221 and newer models

[gmatj]

Nicely done - Very nicely done.
Our sincere Thanks to Qrius for all the time and effort he continuously injects to the Forum. His contribution to the success of DK is invaluable.
G.

[vwpassat]

HI mr Qrius

Would you help me in this matter?
http://www.digital-kaos.co.uk/forums...2/#post1050667

Thank you

[vwpassat]

Hi mr. Qrius

With a lot respect of your knowledge, would you let me know how to escape dtc C235C from SBC W211?
http://www.digital-kaos.co.uk/forums...ervice-230528/

Thank you

Make sure engine is running !!!

In Developer mode you need to go to Entwickelingsdaten - > ansteueringen -> Gesamstliste aller Ansteuerungen

to see how many times brake has been pressed there is a line that says: Bremsenzahler (DJ_GetBrLive)

then 1 line down there you see Bremsenzahler aktualisieren und Lebensdauerzahler F neu berechenen -> click it !
Parameter uINBR = 0
then click F3

1 line down Bremsenzahler auf beliebigen Wert setzen (DJ_SetNBr) -> click it
Parameter uINBR = 0
then click F3


then scroll down untill you see the line's :

Lebensdauerzahler F neu berechenen (DJ_CalcLiveTime)
Parameter uINBR = 0
then click F3

Lebensdauerzahler F neu berechenen und schreiben (DJ_BuildAndWriteF)
Parameter uINBR = 0
then click F3

Log out of SBC !!
log out of verhicle !!

let engine run at least 10 minutes or drive at least 10 minutes

If no coils are damaged , SBC fault code is not AKTUEL nomore

[Fec001]

Here is how to : clean ASSYST Plus Memory
All we need is DAS in Developer mode
In Developer mode : (tested version 07-2009)
Steuergerate (Control units) ->F3
Aufbau (Body) ->F3
ZGW (CGW) ->F3
Entwicklungen (Development data) ->F3
Steuergerate - Anpassungen (Control unit adaption) ->F3
Programmieren (Update) von Steuergeraten (Control module programming) ->F3
Steuergerat programmieren (Auswahl) (Program control unit (Selection)) ->F3

Now we have 2 options to flash the ZGW/CGW with, choose the correct one
Don't panic ! if you choose the wrong file , it terminates process and you can do it over again
Confirm Flash pop-up with Ja (Yes)
After that it says : "Das Steuergerate wurde erfolgreich programmiert"
-> "OK" it ask for a reset -> JA (Yes) ->
ECU Reset (FN_ECU_Reset) ->F3 again ->F3

Now you Completed full History wipe out
Everything discussed in this post is for experimental and educational purposes only

In W164 possible too?
In zgw developement data there is only coding and 1 other is avaible. No control unit programming.
But I need clean ZGW history because somebody plays with it and now the whole service is a mess. Can't reset service etc....

[lorexx]

Here is how to : clean ASSYST Plus Memory
All we need is DAS in Developer mode
In Developer mode : (tested version 07-2009)
Steuergerate (Control units) ->F3
Aufbau (Body) ->F3
ZGW (CGW) ->F3
Entwicklungen (Development data) ->F3
Steuergerate - Anpassungen (Control unit adaption) ->F3
Programmieren (Update) von Steuergeraten (Control module programming) ->F3
Steuergerat programmieren (Auswahl) (Program control unit (Selection)) ->F3

Now we have 2 options to flash the ZGW/CGW with, choose the correct one
Don't panic ! if you choose the wrong file , it terminates process and you can do it over again
Confirm Flash pop-up with Ja (Yes)
After that it says : "Das Steuergerate wurde erfolgreich programmiert"
-> "OK" it ask for a reset -> JA (Yes) ->
ECU Reset (FN_ECU_Reset) ->F3 again ->F3

Now you Completed full History wipe out
Everything discussed in this post is for experimental and educational purposes only

Hi, thanks for sharing, you think it work on all mercedes with assyst plus?

[TULGEYWOODMAN]

Hi, thanks for sharing, you think it work on all mercedes with assyst plus?

This is for earlier Mercs, w203,w211 etc.

[STEEVYAS]

Sprinter W906 2006 CDI4. I'm trying to activate the cruise. In the ESP block, I changed the setting. In the CDI4 block in variant encoding, I see the setting of NSG_TEMPOMAT. Do I understand correctly that the cruise in the CDI4 block has already been included?

[jobela]

Here is how to do it,

In Developer mode :
Kombiinstrument -> Diagnose nach Werkangabe -> Steuergerate-Anpassungen ->
Steuergerate-Anpassungen (Variantencoderierung) -> Variantkodierung Werkeinstellungen ->

In the menu that shows , you scroll down untill you read the line : Tankinfo im Reichweitebild
enable this option
now you have tankinfo in the screen that otherwise only showed range

If the menu you get does not have this Tankinfo im Reichweitebild line, search for the line Bild Reichweite ohne Tankinfo and disable it. Then, look for the line Bild Reichweite und Tankinfo and enable it.

If you allso wanna adjust the way fuel consumtion is showed
you scroll a little more down untill you read the line : Verbrauchanzeige km
you can change it from L/100km into km/l

Scroll down and confirm Coding by pressingF3

if you watch your Instrument Cluster , you notice that scrolling through the menu , nothing changed .

For this , the "Kombiinstrument" needs a reboot.
to do this in Developer mode we go back by hitting F1 -> 3 times
then choose Ansteuerungen -> Gesamstliste aller Ansteuerungen ->
Scroll down untill you see the line : Steuergeraet Resetten (PowerON-Modus) (FN_Reset_SG_Power_ON)
Press F3 and confirm again with F3
Now you will see the "Kombiinstrument" reboots

If you think this would help you
Please dot not forget to click THANKS

These procedures should work on all w203, either one way or the other.

Regards

[basco]

my m8's got xentry das running on his ibm laptop and i'ts in English why then do we have german in the forum? the only time German language really comes up is when you just start
the program after that everything's in english language he's doing master resets and all sorts it's working exceptional because i've seen it in action my only regret is that i still cant get the star multiplexer interface and leads at a reasonable price can any one help in pointing me in the right direction?

[james44000]

Originally Posted by james44000
Originally Posted by james44000
Is it possible possible to change vin in automatic transmission and motor ecu with dev mode?

what is the model and year?


It's for sprinter 2009 cdi

Not always NANTES. But Hex bin will help.


But with obd you save time