Zed-Bull clone users, look here!

**mecadriano** · 1st September, 2010, 11:25 AM

yes cable OBDII
You know if posivel trasponick work with the same ad 900?
if so what should I do?

**drivesure** · 1st September, 2010, 09:19 PM

have a look at this gopelhu.

**MrSporty** · 2nd September, 2010, 05:09 PM

WOW!, i wouldn't have thought it but that add on board actually is a parallel brute force cracker.

Figures why its quite expensive , looks like they use wither 4 or 6 Cyclone 3 FPGA's.

**gopelhu** · 2nd September, 2010, 09:09 PM

Hi all,

Today my pcb was made.
I put it together though I made a mistake I swapped +/- at the USB connector.
I will check and test it and let you know the result.

This PCB is different from that one we bought from the chinese sellers.

Our ZB main unit does not work with v7.0.1 software but my development board is detected by v7.0.1 software.

I hope I can solve it.

Regards,G

**MrSporty** · 2nd September, 2010, 09:59 PM

Nice board, looks easy to dev on.

Are those windows devices just the FTDI/24LC or have you also progged up the ATMEGA's ?

**mecadriano** · 4th September, 2010, 12:07 PM

Gopelhu friend you know tell me if it posivel use my zed qx with trapronics softwer?

**gopelhu** · 5th September, 2010, 07:50 PM

Hi,

NO !!!

Zed-QX hardware works with Zed-QX Anahtar software.
The both devices are Turkish development.
Transpronics sold the licence to Advanced Diagnostics.

Regards,G

**ramhalo** · 6th September, 2010, 04:23 PM

Originally Posted by gopelhu

Hi,

NO !!!

Zed-QX hardware works with Zed-QX Anahtar software.
The both devices are Turkish development.
Transpronics sold the licence to Advanced Diagnostics.

Regards,G

MR Gopelhu is there anyway you can assist with proper upgrading of the t300 or atleast find a way to load the original mvp software on there minus the token deduction of course....Im sure there will be alot of grateful people if you can do this.

**ray-ray** · 6th September, 2010, 04:31 PM

focus! 1 project at a time,that how to work.

**gopelhu** · 6th September, 2010, 08:50 PM

Hi,

I'm sorry to let you know but I didn't have any solutions for T300 yet.
I haven't bought neither T300 nor MPV because I think both are worthless.

I have all the openings and more fuctions and password modification for SBB only !!!

I have solved only this.

Regards,G

**electrosoft** · 7th September, 2010, 03:54 AM

Hi gopelhu i havent the last zed bull setup can you uplad it and can you discrib the protection of this box usb dongle or Smart Card or micro schip atmel and the software it is packed ? im a new member but maybe i can help thanks br.

**snecii** · 7th September, 2010, 03:05 PM

Hello!

I bougth one from china, how can I read out pin code? There is no cable for OBD - Zedbull. Can I buy somewhere or how can I read out?

**paul_12345** · 7th September, 2010, 05:21 PM

Originally Posted by snecii

Hello!

I bougth one from china, how can I read out pin code? There is no cable for OBD - Zedbull. Can I buy somewhere or how can I read out?

Read the thread - there is no obd cable

**paul_12345** · 7th September, 2010, 05:26 PM

Originally Posted by electrosoft

Hi gopelhu i havent the last zed bull setup can you uplad it and can you discrib the protection of this box usb dongle or Smart Card or micro schip atmel and the software it is packed ? im a new member but maybe i can help thanks br.

The protection is the fact that you can not read the microprocessors to get the firmware.

If you copied pcb and cloned the chips you'd have a working clone although it would need tokens updating and there could be protection on this, athough you could always overwrite the chips with the original dumps again refreshing the tokens.

**snecii** · 7th September, 2010, 06:10 PM

Hello!

How can it read the pin from keys? I tryed it with PCF7946 but NO pin.... How can I teach the new key if I change the chip? Copy from the 2. key?
What if there is no 2. key for the car?
I can teach with PIN right?