Lexia PP2000 repair

**Dacha** · 13th July, 2012, 03:43 AM

Hello! I replaced the S-RAM with the interface now works correctly!

**dgjboy** · 13th July, 2012, 07:23 AM

Originally Posted by Dacha

Hello! I replaced the S-RAM with the interface now works correctly!

Thank you for reply Dacha!
Congratulations!

Enviado desde mi HTC Desire usando Tapatalk 2

**tonimk** · 30th December, 2012, 02:37 PM

Hi!
Who can help me to these
how to find both parts; 352A and kb33
Ordering their name from farnell
Thans

**tonimk** · 30th December, 2012, 02:41 PM

Hi!
Who can help me to these
how to find both parts!352A and kb33
Ordering their name from farnell
Thens

**tonimk** · 2nd January, 2013, 12:16 AM

Originally Posted by MOBILTRONIC

Yesterday I had a problem,which is slightly different from other.The interface is not working but was able to run software.So, RAM memory and USB device was correct.Relays did not want to clicking.That two parts I replaced it with one working interface and again everything is ok,without any MCU programming.Best regards.

Hi
how to find both parts 352A and kb33
Ordering their name from farnell
Thenk

**momoauto** · 6th January, 2013, 06:29 PM

Diagbox Flash serial number - YouTube

**liviudiaconu** · 11th January, 2013, 06:45 AM

Originally Posted by tonimk

Hi
how to find both parts 352A and kb33
Ordering their name from farnell
Thenk

352A=NDS352AP
KB33 i don't found, i don't measured but, i suppose is an "resistor network" (3 resistor 33 ohm or 330 ohm on one "chip"). Try measuring and tell us, too.

**liviudiaconu** · 16th January, 2013, 01:30 PM

I want to made one "home benchmark" for lexia.
I want to take an carplug with two "modules", one on K line, another on CAN...

If someone know, what modules communicate directly with lexia by K and CAN?

Thank you

**dany mec** · 24th February, 2013, 08:55 PM

http://www.digital-kaos.co.uk/forums...-lexia-321411/

**dany mec** · 24th February, 2013, 09:00 PM

HELP ME PLEASE

**bubu782001** · 26th February, 2013, 01:36 PM

Lexia is DEAD. It was connected to the car (unsupervised for about 30 min), and after that, interface was dead, no responding, not recognized by windows (not even "unknown device") and the LED stay OFF.
What should i check first ? Can be a firmware problem or USBN9604-28M controller?

Thank you.

**dany mec** · 2nd March, 2013, 02:37 PM

What can happen with USBN9604-28M interface to not go?

**bubu782001** · 3rd March, 2013, 05:58 PM

I don't know, but USBN9604-28M is the first device used between USB port and the rest of the interface, and since is NOT recognized...at all i suspect this chip as "play dead"

**morfej** · 5th March, 2013, 07:35 PM

You can't say if USBN9604 is dead or not ... as all the settings for controller is set from Fujitsu MCU... so apperantly if it get power it is not setup from Fujitsu. USBN9604 is not like FTDI which when it get power it is shown in device manager if connected to computer.

First check power supply of Fujitsu and USBN9604.

br

**tesla001** · 8th March, 2013, 11:33 AM

24mhz crystal change

Thread: Lexia PP2000 repair

Thread Tools

Display

The Following User Says Thank You to morfej For This Useful Post:

Bookmarks

Bookmarks

Posting Permissions