series 60 programming only!

**Biggame520** · 1st February, 2013, 06:14 AM

Here All:

I have a DDEC 3 with serial # 06R0348378 wtih 500HP that I need a file for. Also this is my first time trying to flash a ecm. I have reprogramming software but I do not know where to place the file so that it will be detected when I click Program ECM. Please help and thanks in advance.

**sptecnico82** · 1st February, 2013, 03:42 PM

Originally Posted by Biggame520

Here All:

I have a DDEC 3 with serial # 06R0348378 wtih 500HP that I need a file for. Also this is my first time trying to flash a ecm. I have reprogramming software but I do not know where to place the file so that it will be detected when I click Program ECM. Please help and thanks in advance.

Run the DRS, then copy the file in the folder usually C:/Detroit Diesel/Reprogramation System/Data or C:/Detroit Diesel/Reprogramation System/Unit, I cant remember so well... then you can flash the ECM, but be carefull... if your ECM have nvram memory faults, it can die in the process...

**Biggame520** · 4th February, 2013, 06:53 PM

I will give this a try once I have the correct file. Or can I use other 500 HP file given here?

**sptecnico82** · 4th February, 2013, 09:18 PM

Yes, you can, is better with split and joint.

**ricz** · 13th February, 2013, 02:51 AM

I need a calibration for a 1998 6067GK60 in a Frgtlnr is a 12.7l has a REL_32 computer on it, can some one share a calibration please, preferably something with higher horsepower.
Thanks!!!!

**TDT** · 19th February, 2013, 10:40 PM

what is the best way to reprogram an ECM Detroid, by the 6 way connector? or OEM connector?

**ricz** · 20th February, 2013, 03:24 AM

Both are pretty stable, I will recommend using the oem connector on some J1939 multiplexed trucks, sometimes there is a lot of traffic top 2 transmission, vorad, abs, etc. The calibration download could fail.

**RAULIN** · 20th February, 2013, 05:27 PM

HI FRIENDS I HAVE A ECM WITH MANUAL TRANSMISSION AND I NEED TO INSTALLED IN A TRUCK WITH AUTOMATIC TRANSMISSION I DID BUT THE TRUCK DONT HAVE A SPEED PROPERLY,IS ANY WAY I CAN CHANGE THAT PARAMETER AND PUT AUTOMATIC TRANSMISSION ON AND HOW,THANKS FOR YOUR HELP

**amishmafia00** · 21st February, 2013, 06:35 AM

you can do through ddrs easy. go into change customer calibration and change from manual(0) to auto (16).in dct change transmission type to 16 and change vss_is_etc from 0 to 1. you might have to change one of the settings for the auto trans to be able to activate the jakes but i forget what the name is.

**trehlebov** · 21st February, 2013, 08:03 PM

Originally Posted by Biggame520

Here All:

I have a DDEC 3 with serial # 06R0348378 wtih 500HP that I need a file for. Also this is my first time trying to flash a ecm. I have reprogramming software but I do not know where to place the file so that it will be detected when I click Program ECM. Please help and thanks in advance.

can you give me your cal? i need cal for DDEC 3 with 500hp

**Vitamin** · 23rd February, 2013, 09:15 PM

Hi guys, would you help please - I need to disable Inlet Temp Sensor @ the N2 channel of DDEC IV or just eliminate the fault code from that source by DDCT. How to do that?

**buck4430** · 25th February, 2013, 12:12 PM

Might be wrong but I was told you could not disable and it plays a important part in fuel mileage. I say that because I have a Ddec IV same problem. I have the 4 wire sencer before the turbo. I tried new sencer and checked all the wiring. I am thinking it is in the programing.

Sent from my XT901 using Tapatalk 2

**sptecnico82** · 25th February, 2013, 04:10 PM

Originally Posted by Vitamin

Hi guys, would you help please - I need to disable Inlet Temp Sensor @ the N2 channel of DDEC IV or just eliminate the fault code from that source by DDCT. How to do that?

Is possible disable it, but its true, if the ecm don't know the inlet temperature, your mileage will decrease. Why don't you try to follow the troubleshooting procedure to solve your problem? if its impossible to solve (the only way i know is if you have a bad ecm) then can show you how to do it.

**Vitamin** · 26th February, 2013, 10:05 PM

Sorry guys it was my mistake - I meant ATS @ R1 of DDEC IV w/o EGR

The gurus hercamp and ddmech have given me the advice how to disable that channel by DDCT

Everybody thanks!

**skodafelicia** · 27th February, 2013, 10:56 AM

hi m8
Tell me about version compatibility EMS software
Problem exists - there DDEC IV rel_09D (6067GK60, 06RE107332), he has a problem with the gas pedal - swing connector, works\no. Unit opened - visually fine.
There EMS from EGR engine rel_37D (6067MK6E, 06R0725398) and firmware without ERG rel_32D - when trying to load swears by an incompatible version.
Is there any solution to the problem?