Experience with Autocom

**mexanico1971** · 2nd September, 2013, 02:16 PM

Originally Posted by meteor80

Does someone know why AUtocom CDP+ cannot comunicate with Ford ECU- Fusion 1.4TDCI?
Any solutions?

what ecu ?!
sid 206 ?!

I have the old gold one width oki chip and work good width sid 206 !

regards

**meteor80** · 3rd September, 2013, 08:29 AM

Yes sid 206.
It's new one and there are no Oki chip

Wys***322;ane z mojego Lenovo A820 za pomoc***261; Tapatalk 4

**kiriki6969** · 6th November, 2013, 08:50 PM

I have a CDP+ interface which connects to k-line vehicle but will not connect to CAN cars ive tried on ford firsta 2008, opel vectra 2007, opel astra 2004 and mercedes w207 2011 and always get communication failure
anyone know what problem can be or if a resistor or can transceiver needs changing thanks

**janusz21** · 7th November, 2013, 07:39 AM

Originally Posted by fifas2010
Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):
hi fifas
please i need pass for dump
thank
Best Regard

**NZBrakelathes** · 14th November, 2013, 09:53 AM

Just left the factory who make the none Bluetooth Delphi 150E pity it's missing $2 of parts making it not complete

Sent from my iPhone using Tapatalk

**minchion** · 14th November, 2013, 10:11 AM

I have an interface like this one, can you tell what components are missing ?

Sent from GT-I9100

**NZBrakelathes** · 15th November, 2013, 12:20 AM

Canbus chokes missing from my very limited knowledge possibly little more wrong
And no Bluetooth but cant say that is to bad

Sent from my iPhone using Tapatalk

**NZBrakelathes** · 15th November, 2013, 02:15 AM

I think on this pic you can see the missing chokes two round bits close to each other
The other just have bridges in there place

Sent from my iPhone using Tapatalk

**NZBrakelathes** · 15th November, 2013, 02:18 AM

Oops no wrong side! Sorry

Sent from my iPhone using Tapatalk

**carpin** · 16th November, 2013, 05:19 AM

Speaker on the board is missing to.

**NZBrakelathes** · 17th November, 2013, 11:31 AM

Originally Posted by NZBrakelathes

I think on this pic you can see the missing chokes two round bits close to each other
The other just have bridges in there place

Sent from my iPhone using Tapatalk

Oops this one shows the chokes!!
Yes speaker missing too on cheap shit one

Sent from my iPhone using Tapatalk

**carpin** · 17th November, 2013, 11:28 PM

Hi NZBrakelathes

The components are professional soldered.
How is that board performing?

**gazvts** · 18th November, 2013, 01:42 AM

Originally Posted by carpin

Hi NZBrakelathes

The components are professional soldered.
How is that board performing?

This is actually a picture off my board this one i personally had no problems with any protocols or firmware upgrades

**carpin** · 18th November, 2013, 02:41 AM

gazvts@

And which version software and firmware do you use, latest or?

Thanks

**NZBrakelathes** · 18th November, 2013, 01:26 PM

Originally Posted by carpin

Hi NZBrakelathes

The components are professional soldered.
How is that board performing?

No idea
Sorry this not my product of knowledge etc
Ask gazvt

Sent from my iPhone using Tapatalk

Thread: Experience with Autocom

Thread Tools

Display

The Following User Says Thank You to gazvts For This Useful Post:

The Following User Says Thank You to NZBrakelathes For This Useful Post:

Bookmarks

Bookmarks

Posting Permissions