Experience with Autocom

[ollync]

You are not wrong. Indeed last time I said that, meanwhile removed that post and added corrections here.
So , a final setup will be using 1N4148 or 1N400x diodes. There's no reason to have Zener Diodes.
Good Luck

Another question,
I have tried the interface on VW Touareg 2010 , but no communication with no module except Radio.......Had same problem with Audi
Do you know what IC is guilty for this or maybe relay?

Later edit...

Tryed it on a 2006 Opel Combo 1.7 CDTI...no connection on engine, the only connection i've got to the car was on General OBD

[crashman]

Hello!

I have a CDP+ interface. This works so if software version ok, all ok, leds blue light but I would like to connect with a car the answer is not communication with the car.
I replaced OBD cable but problem is same. I hear if the relays clikk but not communication with anything car. 9241A chips wrong??
thank you very much.

[meteor80]

I have one with the same problem. Relays clicks but message car not respond.

[crashman]

Excellent.

[overs0ull]

Hi guys did someone have a problem like my one or this is normal i have Autocom 2013 and the problem is that when i read mercedes CDI doesn't metter witch one , i never see the injection 1,2,3,4,5,6 on real time and their compesations ,but i see all other things like real presusre ,rpm , voltage and others without injectors in real time .
And can't read spirnters with 14 pin plug but read VW LT with 14 pin socket - did have some problem or i need to make new connection for mercedes 14 pin.
Are this is normal or not ?

[obeids]

Hi there

Can the Autocom CDP Reset Immo Boxes on the Toyota with G Chip or is it best with Techstream?

[sazimam11]

Poor fuctionality on Toyota/Lexus . Use the Techstream . Slow, but works well on cars, made in Japan. (VIN must begin witj JT1 ...)

[manocao]

I need some help, I am missing on my pcb board the U1201

I find out that U1201 is an RC network. (emi filter?)
Any forum member know the specifications?

Thanks

could anyone meter u1201?

edit:

based on u1201 size (0508 case), i have found out it can only be one of these 3 capacitor arrays:

W2F43A2208AT 22pF
W2F43A4708AT 47pF
W2F43A1018AT 100pF

Part Number / Case Size / Current Rating / DC Resistance / Voltage Rating
W2F43A2208AT / 0508 / 50 mA / < 3.0_ / 25 V
W2F43A4708AT / 0508 / 50 mA / < 3.0_ / 25 V
W2F43A1018AT / 0508 / 50 mA / < 3.0_ / 25 V

now we only need to know capacity 22 or 47 or 100pF

http://www.farnell.com/datasheets/58254.pdf

http://bit.ly/1KvnwPy

[kikichou]

autocom 2014.3V released...activation is required
2014.3 autocom sw without keygen

[canoso131]

Please help. Not communicating with BMW E60.

[jo?o antonio]

Ok Mate, great work.
Now, my VCI is a CDP+ one PCB,green, S/n 100251 , I need replace this diode ?
Many thanks for the info.

[cocutanu]

Don't replace them. Just remove them. (D701 and D703)
You'll be fine

[bestb]

Hi all
I have Autocom with strange issue. Basically its dead but when connecting to the car all 4 led`s blink for 1s.
I checked d100, d101 andf f100 I have +12V on it, I cant figure out where is the problem...
Does anyone has schematic diagram ? or maybe you know where to start with ?

[manocao]

could anyone meter u1201?

edit:

based on u1201 size (0508 case), i have found out it can only be one of these 3 capacitor arrays:

W2F43A2208AT 22pF
W2F43A4708AT 47pF
W2F43A1018AT 100pF

Part Number / Case Size / Current Rating / DC Resistance / Voltage Rating
W2F43A2208AT / 0508 / 50 mA / < 3.0_ / 25 V
W2F43A4708AT / 0508 / 50 mA / < 3.0_ / 25 V
W2F43A1018AT / 0508 / 50 mA / < 3.0_ / 25 V

now we only need to know capacity 22 or 47 or 100pF

http://www.farnell.com/datasheets/58254.pdf

http://bit.ly/1KvnwPy

it is 47pf capacitor array
my solution

[motor1]

Hello friends , someone tell how can I get my AUTOCOM . stitched but does not specify a serial number . I would be very grateful .