Peugeot 307 with sagem T5-1 NEC dash and valeo eep 95160

**Fec001** · 15th July, 2011, 07:28 AM

it's possible

**T72** · 15th July, 2011, 08:58 AM

p307 made from 2001 till 2003 have Valeo bsi with 912, and Sageme dash with upd780973, and software in dash who let to reset milage with power up dash. From 2003 p307 have Valeo bsi with 95160 and same Sageme dash with same upd780973 but newest sw, and cant been reseted without programing!
But cars have made in the end 2002 and in the start of 2003 have "new" bsi but "old" type of dash, so some cars can been done BSI onlly.
Its not worth to try do bsi onlly in cars after 2003! Beter charge customer for morer money and program dash and bsi at once! I am 100% shure, becouse have bad experience when milage jumping back, and must program bsi again, and do dash!

**meteor80** · 15th July, 2011, 09:25 AM

You are right T72.
Power up and reset works only if You have old type nec dash and year 2002-2003.
Not work with 95160.

**drpeter** · 15th July, 2011, 11:45 AM

Originally Posted by meteor80

You are right T72.
Power up and reset works only if You have old type nec dash and year 2002-2003.
Not work with 95160.

You can also power up cluster on desk (I still didn't found connections), if cluSter jump to ''000000'' then you only have to do the bsi.

**T72** · 15th July, 2011, 01:47 PM

Originally Posted by drpeter

You can also power up cluster on desk (I found connections), if cluSter jump to ''000000'' then you only have to do the bsi.

and good picture from Renault dash plug

**Fec001** · 12th August, 2011, 09:51 AM

Hi!
I did a P307 2004 5 minutes ago. It has Sagem T5-1 dash with NEC CPU and Valeo BSI with 95160 eep. I did only the BSI and it is working perfectly. 100% SURE on this model enough to do only BSI.

**swingman26** · 12th August, 2011, 10:01 AM

Hi,

I just do one 307 2003 with 95160 bsi and dash nec. Tried to make only bsi and not work. Need to make dash + Bsi.

Also on BSI with 912 you can make only BSI. Need to turn ignition on without bsi in car.

IMPORTANT : This can do only with a special tool. Not possible with dp3 or enigma or ...expensive tool.

Need to read 912 with a programmer. Upload dump and correct with lickznik 9.2.

Look dump after mileage correction. The 10 last lines, write 00000000000000000000000000000000000000000000000000 00000000000000000000

It's necessary to syncronize bsi and dash. Mileage jump from bsi to dash.

Trust me.

**Fec001** · 12th August, 2011, 10:07 AM

Sorry I was wrong. After I wrote my previous post I started to testing the car. drive the car, disconnect battery etc. When I connected the battery again the km is jumped back.......tricky tricky peugeot

**swingman26** · 12th August, 2011, 10:16 AM

Look to file on hex editor. After mileage correction.

**ubistvo** · 26th May, 2018, 04:40 PM

TESTED
Work ok
Thanks man

**otojm** · 9th July, 2018, 10:58 AM

Originally Posted by ubistvo

TESTED
Work ok
Thanks man

for what car- dash & bsi ??? please

**zevi36** · 26th July, 2018, 06:01 PM

Hi guys, I have a 307 with a T5-1 dash and 95160 bsi. The dash is dead and i changed for a 2nd hand one, and now the odometer show 211671kms. The real kms are 87552. Could someone change the kms in the bsi? and means that i need to change also the kms in the dash? or i must feed the dash in bench before?
thanks in advance