renault edc16c3 problem
Register
Results 1 to 13 of 13
  1. #1
    Top Poster

    Join Date
    May 2010
    Posts
    118
    Thanks Thanks Given 
    60
    Thanks Thanks Received 
    5
    Thanked in
    5 Posts

    Default renault edc16c3 problem

    Hi guys, have a renault megane 2003 edc16c3 which following a bad read with mpps v10 has left the ecu with no injector coding. All injectors show a coding of A. I have tried to manually program the injector codes with clip but it fails stating internal electrical failure.
    The car starts and runs but only to 1500rpm, MPPS read the id ok but failed almost straight away when attempting a normal read instructing me to contact amt, my mpps is a clone. Can anyone suggest a fix please?

    Many thanks in advance.

  2. #2
    DK Veteran
    Join Date
    Dec 2010
    Location
    UK
    Posts
    378
    Thanks Thanks Given 
    5
    Thanks Thanks Received 
    6
    Thanked in
    3 Posts

    Default

    BDM ori data and start again.

    MPPS doesnt recode config data such as inj coding on Renault or PSA, so best to use tool that does or BDM.

  3. #3
    Senior Member
    Join Date
    Dec 2010
    Posts
    276
    Thanks Thanks Given 
    5
    Thanks Thanks Received 
    10
    Thanked in
    8 Posts

    Default

    You must code injectors with proper diagnostic tools like renault can clip without any problem, I did it few times!

  4. #4
    Banned
    Join Date
    Feb 2010
    Location
    .
    Posts
    2,895
    Thanks Thanks Given 
    46
    Thanks Thanks Received 
    725
    Thanked in
    524 Posts

    Default

    you can find the codes written on each injector, make sure you count injector 1 from the belt

  5. #5
    DK Veteran
    Join Date
    Dec 2010
    Location
    UK
    Posts
    378
    Thanks Thanks Given 
    5
    Thanks Thanks Received 
    6
    Thanked in
    3 Posts

    Default

    Cyl 1 is flywheel end

  6. #6
    DK Veteran
    furnata's Avatar
    Join Date
    Feb 2010
    Location
    Bulgaria
    Posts
    815
    Thanks Thanks Given 
    227
    Thanks Thanks Received 
    442
    Thanked in
    133 Posts

    Default

    And the injectors code is writen in e2prom -8pin soic

  7. #7
    DK Veteran
    i_shot_the_sheriff's Avatar
    Join Date
    Nov 2008
    Posts
    1,339
    Thanks Thanks Given 
    186
    Thanks Thanks Received 
    199
    Thanked in
    125 Posts

    Default

    ARe the injectors in the 95160 8pin? If yes is there a way to add them manually (with hex editor?)

  8. #8
    Member mbtuning's Avatar
    Join Date
    Apr 2012
    Posts
    50
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    1
    Thanked in
    1 Post

    Default

    just use renault can clip ... in most of cases works great.
    Magpro2 / MagBDM / X17 / New Genius / Powergate Full / MPPS / FGTech / WINOls 2.20 and much more ...

    Chiptuning / DPF OFF / EGR OFF / Hot start - solutions ...

    MBTUNING.RO

  9. #9
    DK Veteran
    i_shot_the_sheriff's Avatar
    Join Date
    Nov 2008
    Posts
    1,339
    Thanks Thanks Given 
    186
    Thanks Thanks Received 
    199
    Thanked in
    125 Posts

    Default

    It is weird that can clip won't program the injectors for this ecu!!!! I've tried another ecu with different numbers and it worked,,, but not with this one!
    That why i'm searching for a way to add them manually via the eprom

  10. #10
    DK Veteran
    ecutuners's Avatar
    Join Date
    Apr 2011
    Location
    United Kingdom
    Posts
    840
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    518
    Thanked in
    164 Posts

    Default

    The codes are inside eeprom in hex format,read eeprom of the spare ecu and then program some injectors to it, read eeprom again you will see where they are stored
    Kess v2 FW 5.017 full unlimited token - Ktag 7.020 full unlimited token
    ALL EDC17/MED17 EEPROM CHECKSUM + VAG IMMO OFF BY EEPROM - NO SAFE

    EDC16/17 POPCORN - ME7/7.5 ANTI LAG - LAUNCH ALS/NLS

    DPF EGR DTC SCR, Custom Tuning, Damos Translation, FRF / SGO Files
    Professional Engine Software Development





  11. #11
    DK Veteran
    i_shot_the_sheriff's Avatar
    Join Date
    Nov 2008
    Posts
    1,339
    Thanks Thanks Given 
    186
    Thanks Thanks Received 
    199
    Thanked in
    125 Posts

    Default

    THe problem is that the Injector codes are not in plain text (in the hex format)....but are encrypted!!!

  12. #12
    DK Veteran
    koolstuff's Avatar
    Join Date
    Nov 2015
    Location
    Dakar (Senegal)
    Posts
    1,251
    Thanks Thanks Given 
    223
    Thanks Thanks Received 
    741
    Thanked in
    234 Posts

    Default

    i have similar problem with renault master2 and my clip can is bricked

  13. #13
    DK Veteran
    Aivis3's Avatar
    Join Date
    Sep 2016
    Location
    Latvia
    Posts
    363
    Thanks Thanks Given 
    75
    Thanks Thanks Received 
    107
    Thanked in
    73 Posts

    Default

    Easy with Galletto4. Need to read injector file, save, repair it and upload to ecu.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.