VAG-COM/VCDS LATEST DUMPS

[gopelhu]

It is not clear, this is for FTDI BM/BL?
thanks for you work and time!

Hi,

No, its FT232RL, but this weekend i will finished my solution

Regards all

[alexm1]

I tried to split .bin from the rar, into the flash.hex +eeprom.hex, using ponyprog2000, but when I open eeprom file with xtremeburner it says: "This file is too large for selected AVR microcontroler..."
What I am doing wrong?

edit: my bad, old version of pony, tried latest version and job done.
Cable works ok, not tested yet for long coding.

L.E. too bad, long coding not working .

[abdelamjid]

thank you for sharing

plz help me how to flash my vcds 11.11 ( china clone )

mcu: D79F8513A
MCP2512
FTDI:ft232bl
thanks
best regards

[fantomel]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese

P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.

[danielgatan]

12959559_10206330114871626_1888747226_o.jpgHello mates! I try to reflash my interface 11.11 with upa usb...i can read read and program.. after programming say programming succes...but if i try to verify i have error and when i read i have dump empty.."like in pitures" lock bits and fuse i use that from pictures12970676_10206330148192459_2086262073_o.jpg12991849_10206330114991629_329442474_o.jpg12991945_10206330116631670_133242055_o.jpg

[cocutanu]

It's normal you can not verify Atmega. Once you wrote it with fuses it gets locked.
So, you'll not be able to read it again for verifying.

[alexm1]

@danielgatan
After reflash your cable it is working????
It is true that after reflash your dump will be encripted but can not be "empty".

[eliotroyano]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese
P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.

Thanks Fantomel I have tested your solution for V12.12 FT232BL but doing logging it only last some seconds and lost connection. Mainly happends with CAN cars. Two laptops and two BL cables was tested with same results. Do you have an idea what can be wrong?

[abdelamjid]

thank you fantomel

best regards

[abdelamjid]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese

P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.

thank you for your response

[0n0t0le]

hello everybody. i have genuine ross-tech interface with revoked license. there is no way to register it. it is blacklisted by ross-tech. There are atmega162 and ftdi 232RQ inside. Is there any solution to make it works?

[loveya]

hopefully this will work for me

thanks

[MacNB]

Have a VAG 11.11 cable for a while (18 months).
Worked fine (could read codes, reset DTC's, change Long Coding, etc).

Recently, it seems it has become locked out saying certain functions need a license now.
I can only think that the Wi-Fi was on when I last used it and the VCDS 11.11 s/w has re-programmed the cable and blocked it.

Looking for help to see if it can be salvaged.
The chips on the board are:

ATMEGA162
GAL16V8B
93C56WP

FT232BL
MCP2515
TJA1050

Plus there's one empty chip pad set. See pics:




If it can be re-programmed, any pointers would be great (which programmer to buy, wiring the programmer, which dumps, etc). Once I have all the bits (H/W & S/W), I'll write up a guide as I cannot find one that is in one place. Thanks.

[gopelhu]

hello everybody. i have genuine ross-tech interface with revoked license. there is no way to register it. it is blacklisted by ross-tech. There are atmega162 and ftdi 232RQ inside. Is there any solution to make it works?

Can you upload some pics for your interface?

To All,

I have a BM/BL 93cxx dump but i dont have any interface to test it, I have 3pces RL .... GRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR

Maybe if i get one, i will test it and upload the ept file.

Regards,G

[MacNB]

Still looking for help to repair my cable (with ATMEGA162, GAL16V8B, 93C56WP, FT232BL, MCP2515, TJA1050) .
Looking for the dumps for 11.11.
Device manager tells me the cable VID=0403 and PID=FA20.