Epson SX125 waste ink counter reset
Register
Page 1 of 19 12345611 ... LastLast
Results 1 to 15 of 279
  1. #1
    Top Poster

    Join Date
    Jul 2010
    Location
    UK
    Posts
    133
    Thanks Thanks Given 
    46
    Thanks Thanks Received 
    202
    Thanked in
    70 Posts

    Default Epson SX125 waste ink counter reset

    Hey guys,

    It took me ages to source a SX125 waste counter reset program that works, so I thought I would pop it on here.

    I've uploaded it into the download section, but thought I may as well pop it on here with a bit of guide too.

    I've only tested it on XP 32bit, with a UK SX125 printer, so that's what the instructions will be tailored for. By all means try it on other OS's and feel free to post results.

    Reset instructions for SX125:

    • Install printer if not already installed.
    • Download and extract attached file into a folder on your hard drive.
    • Run 'AdjProg.exe' and click 'Accept' on the splash screen then click on 'Select' at the top.
    • From the pull down boxes, select 'Epson Stylus TX121' for 'Model Name' and 'ESP' for 'Destination', click 'OK'.
    • Click 'Particular adjustment mode' then from the '---- Maintenance ----' section, select 'Waste ink pad counter' then click 'OK'.
    • Click 'Check' on the bottom right, this will query the printer and give information of ink shots and so on.
    • Tick the two boxes on the left, 'Main Pad Counter' and 'FL Box Counter', then click 'Initialize'.
    • It should come up with a message abut restarting your printer, do it!

    Job done, carry on printing!

    I recommend getting a waste ink tank for your printer, have a Google for one, the waste ink pipe is easily accessible from a clip in hatch on the back of the printer.

    Hope that helps, if it's useful, don't forget to thank
    J.

    -------------------------------------------------------------------------------------------
    right, rubbish is still being posted to gain access to this file even after a warning, i will say this one more time, DONT KEEP POSTING RUBBISH TO GAIN ACCESS TO THIS FILE, keep your posts to questions or an answer to another post, THE NEXT PERSON WHO POSTS.....THANKS OR GOOD POST OR JUST WHAT I NEEDED OR ANY OTHER RUBBISH TO GAIN ACCESS TO THIS FILE WILL BE BANNED, YOU HAVE BEEN WARNED !!! DK STAFF

    YOUR FIRST POST GOES HERE-----> http://www.digital-kaos.co.uk/forums/f2/

    -------------------------------------------------------------------------------------------
    Attached Files Attached Files
    Last edited by gmb45; 5th February, 2013 at 06:45 PM.

  2. The Following 61 Users Say Thank You to johnnybeast For This Useful Post:

    atelzut (9th October, 2014), balibee (20th May, 2013), bertione (29th January, 2014), boaaar (24th October, 2013), c2804021 (15th December, 2013), coldblue (28th May, 2013), dpodor12 (19th November, 2013), ebalkiss (12th November, 2014), eddyvankenoby (22nd January, 2014), FalconMigz (2nd September, 2014), ferrasur (6th January, 2015), fiat 0000 (25th October, 2013), fischman (2nd June, 2013), hamito (29th July, 2013), haveitdave (2nd July, 2014), hrv (7th July, 2013), isiemelink (18th September, 2013), ivanpricic (19th April, 2013), josej69 (3rd May, 2020), korgao (20th April, 2014), lambrosg22 (18th November, 2013), Leitxo (29th October, 2013), magestery (21st October, 2013), Malcolm974 (13th May, 2013), Manhunt (24th June, 2014), mark2024 (25th February, 2024), marsarts (21st October, 2015), masterren44 (3rd April, 2014), metak (21st December, 2016), murch (8th April, 2014), musta22 (23rd April, 2022), northernheart (22nd October, 2013), PCMEDIC (30th September, 2014), pippo3210 (7th February, 2024), protor (15th January, 2015), ps2k (24th November, 2015), ptolemaeus (28th March, 2013), sbixx (7th April, 2013), shevor (8th March, 2019), shuffleinc (12th August, 2013), sidwho (15th May, 2013), sumpy (7th July, 2014), telecomonde (19th June, 2013), thessgr (26th June, 2013), tony18101963 (25th May, 2013), tr0r (30th June, 2014), xxhd (28th June, 2014), yiwen akeni (17th December, 2013)

  3. #2
    Newbie
    Join Date
    Apr 2012
    Posts
    15
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    1
    Thanked in
    1 Post

    Default epson stylus sx130

    dear
    does this software work on Epson stylus sx130
    thank you

  4. The Following User Says Thank You to akramjef For This Useful Post:

    yiwen akeni (17th December, 2013)

  5. #3
    Top Poster

    Join Date
    Jul 2010
    Location
    UK
    Posts
    133
    Thanks Thanks Given 
    46
    Thanks Thanks Received 
    202
    Thanked in
    70 Posts

    Default

    Hello,
    The reset program is just for the Epson SX125, but it might work for the SX130 as they are very similar. Other people have reported it working on the SX130. Give it a blast!!

    J.
    Last edited by johnnybeast; 2nd September, 2012 at 01:28 AM.

  6. The Following User Says Thank You to johnnybeast For This Useful Post:

    yiwen akeni (17th December, 2013)

  7. #4
    Newbie
    Join Date
    Apr 2012
    Posts
    2
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    1
    Thanked in
    1 Post

    Default hope

    hello, I'm new here.. I was searching just this software because my sx125 doesn't recognize a cartridge (that is still with ink). I hope it will work thanks

  8. The Following User Says Thank You to bel3nebroso For This Useful Post:

    yiwen akeni (17th December, 2013)

  9. #5
    Newbie
    Join Date
    Apr 2012
    Posts
    2
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    1
    Thanked in
    1 Post

    Default

    I've done all the steps, but the problem is always the same black cartridge not recognized, but till yesterday it worked and the cartridge had some ink remaining...
    Some suggestions?

  10. #6
    Top Poster

    Join Date
    Jul 2010
    Location
    UK
    Posts
    133
    Thanks Thanks Given 
    46
    Thanks Thanks Received 
    202
    Thanked in
    70 Posts

    Default

    Suggestions:

    1 - Are you using genuine or copy ink? If it's copy ink then theres a chance that the chip is telling the printer that the ink is empty or the chip has failed. Try changing the cartridge for a new one.

    The reason for the 'not regonised' message instead of 'out of ink' message is the sophistication level of the copy chips, they will report the level of ink but when the ink is out it comes up with 'not recognized' even if there is still ink left in the cartridge. Clever huh?!

    2 - The chip contacts in the back of the head could be corroded or bent, get a torch, take the cartridge out and have a look, if they are, pull the power out and clean or gently bend them back.

    3 - Your printer's stuffed. I've seen it happen only a few times, the microprocessor that reads the chips could be faulty, time to give yourself a treat! A lovely new printer

    Hope that helps, let me know! Always good to get feedback.
    J.

  11. #7
    Newbie
    Join Date
    Apr 2012
    Posts
    2
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    thank you very much i have sx125 and it work for me

  12. #8
    Newbie
    Join Date
    Apr 2012
    Posts
    2
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Thanks so much! It finally worked after disabling my antivirus for a while. Please reach me on ( no addys ) for more talks. Thanks once again.
    Last edited by gmb45; 22nd May, 2012 at 09:52 AM.

  13. #9
    Newbie
    Join Date
    Apr 2012
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default Thnaks

    Thanks! I'm hoping this will reset the ink pad counters, it's telling me I need to service because I've head cleaned so many times when installing a CISS

  14. #10
    Newbie
    Join Date
    Apr 2012
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    It took me ages too to source the same thing- im thankful to God that i finally bumpep onto one (A proven one most of of all). i hope to download it right away.

  15. #11
    Newbie
    Join Date
    Apr 2012
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    i had a problem with my epson sx 125 but i hope you guys can help

  16. #12
    Newbie
    Join Date
    Apr 2012
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default hey

    does this helped anyone who has copy cartridge and not recognizing the black one ... does it helped??

  17. #13
    V.I.P. Member
    Canker_Canison's Avatar
    Join Date
    May 2010
    Location
    12th Level of Hell
    Posts
    3,904
    Thanks Thanks Given 
    40
    Thanks Thanks Received 
    196
    Thanked in
    134 Posts

    Default

    Quote Originally Posted by zagervbk View Post
    does this helped anyone who has copy cartridge and not recognizing the black one ... does it helped??
    No it won't. The black cartridge will have to be changed.
    Canker

    "Animal, vegetable or mineral... I'll do anything, to anything, with anything"
    - The Baby Eating Bishop of Bath & Wells
    [COLOR=Green]

  18. #14
    Newbie
    Join Date
    Apr 2012
    Posts
    15
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    1
    Thanked in
    1 Post

    Thumbs up epson sx130 resetting

    dear Canker_Canison
    thank you for this program ,i used it for my Epson stylus sx130
    and it work fine .it reset waste ink pad counter to zero.
    so this program can be used for Epson model:
    ME320 , SX125 , TX121 ,and SX130
    good luck.

  19. #15
    V.I.P. Member andy91's Avatar
    Join Date
    Aug 2010
    Location
    East Midlands
    Posts
    3,583
    Thanks Thanks Given 
    137
    Thanks Thanks Received 
    193
    Thanked in
    154 Posts

    Default

    Its ok using the program to reset your counter but the reason its there is to stop waste ink overflowing and spoiling your new carpet
    Most waste ink gets held in a sponge so its worth trying to soak up any excess ink when you reset the counter.

    Andy.

  20. The Following 7 Users Say Thank You to andy91 For This Useful Post:

    darkyinlove (24th May, 2013), imrefinnej (9th February, 2014), lapvinh (17th October, 2013), sjbrit (10th October, 2014), yiwen akeni (17th December, 2013)

 

 
Page 1 of 19 12345611 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.