Zed-Bull clone - Second Life

[gwee]

OK but even this 2003 prado with 4D it is not working here is the attachement please can you see what is wrong?

Loaded your dump to effi, 100% working. Unless you don't have module 117

[sierra]

Loaded your dump to effi, 100% working. Unless you don't have module 117

In this car keys lie in immo and in ecu.
In ecu keys are a little bit ciphered

[gwee]

In this car keys lie in immo and in ecu.
In ecu keys are a little bit ciphered

Done a few Prado 120 lost key, all via OBD reset and add key

Never try to read dump, but I think effi dump to key should work, no need ecu

[simaservis1108]

For Sierra to add to Effi.
Daihatsu/Perodua Tokai Rika immo box(4D-67).
Daihatsu:Cuore(2004-),Materia(2004-),Sirion(2004-),Terios(2004-).
Perodua:Myvi,Viva,Alza.
Memory 93c66.
Expected file size is 512 bytes.
In attachment is immobox dump and picture with memory squared in red.

Have a good time all,
Sima

daihatsu immo tokai rika.rar

[simaservis1108]

For Effi program.
Keihin ECU(4C).
Memory device:93c66.
Expected file size is 512 bytes.
Suzuki Burgman

suzuki burgman.rar

Kind regards,
Sima

[simaservis1108]

For Effi program.
Mitsubishi immobox(ID46)
Memory device is 24c16.
Expected file size is 2048 bytes.
Mitsubishi:Outlander(2006-),Lancer(2006-)
mitsubishi lancer immo 2006.rar

WBR,
Sima

[Chokito5]

try to turn on ignition without any transponder in key, does light flash? if stay on then you have other issue, and sometimes after programming, the uch will lock you out, leave ign on for 1 min with red led on solid, then turn off and turn straight to crank and car will start if everything is ok.

ps - you need to pre code pcf7936 AND program with pincode after, better to use a new pcf7946 on a used remote, pre code with effi or zed clone and program with pin code.

ninja

Yes, turn on ignition without any transponder in key, the light flashes. If I turn on ignition with the original key, the led on. I tried to programmed with CLIP the original key, this is same.
I tried to igniton on for 1 min, and turn off it, and straigt to crank, the starter motor working, but the engine is not started, the IMMO led ON. I tried to programmed again the original key, but nothing changing.
I read the fault code from the Immo, but there is no fault code. I would like to read the fault codes from the computer of the Engine, but I can't connect to this computer. If the immo active, Can I not connect to the computer of the engine?

Is the key the problem? The car is ok? Or the car has any problem?
I order a new transponder for this key, maybe that will help.

[mvtamele]

You already run a car?
If isn't present, write to me tomorrow on an email, I will try to help you.

Not yet my friend the is not running till now I don't know why can you help me?

[mvtamele]

Loaded your dump to effi, 100% working. Unless you don't have module 117

I got module 117 as my effi is original and up to date first it was coping the keys as ID 4D 63 after update it puts 4D 67 burning car don't start did you see the key data? What is possible wrong? It's possible to immo off?

[gwee]

I got module 117 as my effi is original and up to date first it was coping the keys as ID 4D 63 after update it puts 4D 67 burning car don't start did you see the key data? What is possible wrong? It's possible to immo off?

I think your ECU data has been changed by someone before you, try with these two dumps.

After that make key with effi module 117.

[antibisic]

Yes, turn on ignition without any transponder in key, the light flashes. If I turn on ignition with the original key, the led on. I tried to programmed with CLIP the original key, this is same.
I tried to igniton on for 1 min, and turn off it, and straigt to crank, the starter motor working, but the engine is not started, the IMMO led ON. I tried to programmed again the original key, but nothing changing.
I read the fault code from the Immo, but there is no fault code. I would like to read the fault codes from the computer of the Engine, but I can't connect to this computer. If the immo active, Can I not connect to the computer of the engine?

Is the key the problem? The car is ok? Or the car has any problem?
I order a new transponder for this key, maybe that will help.

Check power on the engine ecu

[mvtamele]

I think your ECU data has been changed by someone before you, try with these two dumps.

After that make key with effi module 117.

IS THIS WITH THE SOME PART NUMBER LIKE MYNE?
immo TOYOTA 89780 60360
ECU 89661-6A170 5VZ

[gwee]

IS THIS WITH THE SOME PART NUMBER LIKE MYNE?
immo TOYOTA 89780 60360
ECU 89661-6A170 5VZ

Can't remember ecu number, no harm trying

Make key with my immo dump and load both dumps to car.

[ninja123]

Check power on the engine ecu

This is correct, you have bad wiring or power supplt to engine ecu, this is why you cannot comms with it, check relays and wiring in the engine bay fuse box area, check for supplies at ecu plug.

ninja

[hansbabas]

Hello to all, how do I get the software EEFI?